Linksys WRT120N Support Question
Linksys WRT120N Support Question
Find answers below for this question about Linksys WRT120N - Wireless-N Home Router Wireless.Need a Linksys WRT120N manual? We have 2 online manuals for this item!
Question posted by Hodpage on November 29th, 2013
How To Bridge Wrt120n
The person who posted this question about this Linksys product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Linksys WRT120N Manual Pages
User Guide - Page 2
All rights reserved.
WARNING: This exclamation point indicates that there is a caution or warning and it .
and certain other countries. Wireless-N Home Router
About This Guide
i WEB: This globe icon indicates a noteworthy website address or e-mail address. If you use an older web browser, you should pay special ...
User Guide - Page 3
... 21 Administration > Management 23 Administration > Log 24 Administration > Diagnostics 24 Administration > Factory Defaults 25 Administration > Firmware Upgrade 25 Status > Router 26 Status > Local Network 26 Status > Wireless Network 27
Appendix A: Troubleshooting
28
Appendix B: Specifications
29
Appendix C: Warranty Information
30
Limited Warranty 30
Wireless-N Home Router
ii
User Guide - Page 4
... d'Industrie Canada 33 Wireless Disclaimer 33 Avis de non-responsabilité concernant les appareils sans fil 33 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 34
Appendix E: Software End User License Agreement
38
Cisco Products 38 Software Licenses 38
Wireless-N Home Router
iii
User Guide - Page 5
...‑based utility. There are online.
You can use Wi-Fi Protected Setup, run the Setup Wizard, or refer to automatically configure wireless security for choosing the Linksys by Cisco Wireless-N Home Router. It flashes blue for approximately five seconds, or restore the defaults from the Administration > Factory Defaults screen of the product label...
User Guide - Page 6
..., flat, dry, and sturdy. Drill two holes into the wall-mount slots. Maneuver the Router so the wall-mount slots line up with the two screws.
5. Cut along the dotted...screw into each hole and leave 3 mm (0.12 inches) of an electrical outlet.
2. Wall-Mounting Template
Wireless-N Home Router
2 Determine where you use is within reach of its bottom panel. Make sure the holes are needed ...
User Guide - Page 7
...is more secure than a traditional wired network. Wireless-N Home Router
Wireless Security Checklist
4.
Combine letters and numbers to avoid using standard words that are adopting them...will be found in length. Additional Security Tips
•• Keep wireless routers, access points, or gateways away from other wireless networks that do not support WPA. WEB: For more vulnerable to ...
User Guide - Page 8
... page of this chapter to clear your language To use . Additional tabs will change the Router's general settings. Wireless-N Home Router
Advanced Configuration
Setup > Basic Setup
Language
Select your changes. Internet Setup
The Internet Setup section configures the Router to the Router. A login screen will appear. (Non-Windows XP users will be available after you to...
User Guide - Page 9
... one DNS (Domain Name System) server IP address. Then configure the following:
•• Specify an IP Address This is the Router's IP address, when seen from the Internet. Wireless-N Home Router
Advanced Configuration
Service Name (Optional) If provided by users on Demand. PPTP Point-to-Point Tunneling Protocol (PPTP) is set to access...
User Guide - Page 10
... to automatically re-establish your connection as soon as you are disconnected, then the Router will automatically re-establish your ISP. Wireless-N Home Router
Advanced Configuration
Keep Alive: Redial Period If you select this option, select Connect on Demand enables the Router to have elapsed before your ISP. Username and Password Enter the Username and...
User Guide - Page 11
...-screen information, click Refresh.
Router IP
DHCP Server Setting
The settings allow you to each computer on your network. DHCP Server Setting
Wireless-N Home Router
Advanced Configuration
DHCP Server DHCP... changes the settings of the local network. The default is performed through the Wireless tab. Wireless setup is 192.168.1.100. A DHCP server automatically assigns an IP address ...
User Guide - Page 12
...to three DNS Server IP Addresses here. Otherwise, leave this button. Setup > DDNS
The Router offers a Dynamic Domain Name System (DDNS) feature. It is the wildcard). DDNS
DDNS ...you assign a fixed host and domain name to sign up to functioning DNS servers. Wireless-N Home Router
Advanced Configuration
The features available on the DDNS screen will change. Before you use a...
User Guide - Page 13
... connection is disabled, dynamic routing will be enabled. Some ISPs will change.
Wireless-N Home Router
Advanced Configuration
Click Save Settings to apply your changes, or click Cancel Changes.... MAC Address Enter the MAC Address registered with your changes.
Static Routing sets up the Router's advanced functions. When the NAT setting is enabled, the Dynamic Routing feature is a pre...
User Guide - Page 14
... it easy to set up your primary
10 If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, select Disabled. If you have client devices, such
Wireless-N Home Router
Advanced Configuration
as wireless adapters, that allows for the Channel Width setting, then Wireless-N can select the wireless standards running on the keyboard). Enter Route Name Enter a name for...
User Guide - Page 15
... channel from the dropdown menu. If you are configuring. Wi-Fi Protected Setup
There are not sure which channel to your changes.
Wireless > Basic Wireless Settings (Wi-Fi Protected Setup) Wireless-N Home Router
Wi-Fi Protected Setup > Congratulations
Method #2
Use this method if your client device has a Wi-Fi Protected Setup PIN number. 1. After the...
User Guide - Page 16
... client device asks for further instructions. Passphrase Enter a Passphrase of 8-63 characters.
Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. Wireless-N Home Router
12 After the client device has been configured, click OK. The default is a security standard stronger than WEP encryption. Chapter 3
Method...
User Guide - Page 17
... digits) or 104/128 bits (26 hex digits). The default is connected to the Router.)
IMPORTANT: If you did not enter a Passphrase, enter the WEP key manually. Wireless-N Home Router
Advanced Configuration
Shared Secret Enter the key shared between the Router and the server. Encryption Select a level of algorithm, AES or TKIP or AES. The...
User Guide - Page 18
... by default. This button is not selected by MAC Address, either permitting or blocking access, select Enabled. Wireless-N Home Router
14
Security Mode > WEP
Encryption Select a level of the wireless devices transmitting within your changes. If you did not enter a Passphrase, enter the WEP key manually.
Chapter 3
WEP WEP is a basic encryption method, which...
User Guide - Page 19
... setting is available if the Network Mode is RADIUS or WEP. Wireless > Advanced Wireless Settings
Wireless-N Home Router
Advanced Configuration
Advanced Wireless
AP Isolation This option isolates all wireless clients and wireless devices on the speed of data transmission, configure the Transmission Rate setting.) The Router will advertise its Basic Rate to the MAC Address Filter List...
User Guide - Page 33
Appendix B
Appendix B: Specifications
Model
WRT120N
Standards
IEEE 802.3u, 802.11g, 802.11b, Draft 802.11n
LEDs
Power, Internet, Wireless, Wi-Fi Protected Setup™, Ethernet (1-4)
Ports
...Storage Temp.
-20 to 60°C (-4 to 140°F)
Wireless-N Home Router
Specifications
Operating Humidity 10 to 80%, Noncondensing Storage Humidity 5 to 90% Noncondensing
Specifications are subject to ...
Quick Installation Guide - Page 1
QUICK INSTALLATION GUIDE
Wireless-N Home Router
Model: WRT120N
Package Contents
• Wireless-N Home Router • Setup Software and User Guide on CD-ROM • Quick Installation Guide • Network Cable • Power Adapter
Linksys Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
FREQUENTLY ASKED QUESTIONS - WAP4410N
...short prongs into place. 7. Does WAP4410N supports Wireless-B/G network mode? The Router supports eight security modes: WEP WPA-Personal WPA2-Personal WPA2-Personal...System Performance tab. 8. Does Wireless Bridge and Wireless Repeater mode will ONLY work with the WAP4410N? WMM (Wi-Fi Multimedia) is only a bridge from a wireless network. Step 3: Then, select Restore... -
Configuring the Network Media Hub with a WGA600N
... if the Media Hub was set to DHCP or for easy setup or as Wireless Bridge . Step 2 Connect your PC. ( For this step. Static IP address is recommended Step 6 Wireless Network Name , please enter the Step 7 Wireless Security , please enter your Wireless router that you can either leave it to DHCP. The Network Media Hub is... -
Configuring the Basic Wireless Setting of the WET610N
... digits) or 104/128 bits (26 hex digits). When you should change the default. The SSID is case-sensitive and must be done by the Bridge and wireless router or access point. Enter the key shared by accessing the web-based setup page. For added security, you are described in...
Similar Questions
Linksys Wireless N Home Router Wrt120n How To Reset Password
(Posted by erdjoh 9 years ago)
How To Change Password On Tmobile Hotspot At Home Router Linksys
(Posted by amywaevilwi 10 years ago)
How To Connect Linksys Wrt120n Wireless Router To Att Dsl
(Posted by BJAmerit 10 years ago)
How To Reset A Tmobile Hotspot At Home Router Linksys
(Posted by poldap 10 years ago)
I Just Need The Drivers For Free To Linksys Wrt120n Wireless Router
(Posted by larkenkyle 12 years ago)