Home » Linksys » Wireless » Linksys WAP610N

Linksys WAP610N Support Question

Find answers below for this question about Linksys WAP610N - Wireless-N Access Point.
Need a Linksys WAP610N manual? We have 1 online manual for this item!

Linksys Overview Questions Manuals Reviews Videos Research

Question posted by jawabrehbusiness on September 30th, 2014

Bridge Mode

how to configure it to work as repeated/bridge.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TheWiz on September 30th, 2014 6:42 AM

This answer was accepted by the poster of the original question.

TheWiz

Member since:
October 13th, 2011

Points: 25,383,424

1,100
points

Sorry but this access point cannot be used as a repeater.

Related Linksys WAP610N Manual Pages

User Guide - Page 1

USER GUIDE Wireless-N Access Point with Dual-Band Model: WAP610N

User Guide - Page 2

... through the User Guide you may have to while using the product. Online Resources Website addresses in the U.S. WARNING: This exclamation point indicates that there is a caution or warning and it . Wireless-N Access Point with Dual-Band About This Guide i Resource Website Linksys www.linksysbycisco.com Linksys International www.linksysbycisco.com/international Glossary www...

User Guide - Page 3

... Configuration 3 How to Access the Browser-based Utility 3 Setup > Basic Setup 3 Wireless > Basic Wireless Settings 4 Wireless > Wireless Security 5 Wireless > Wireless MAC Filter 7 Wireless > WMM 8 Wireless > Advanced Wireless Settings 11 Administration > Management 12 Administration > Factory Defaults 12 Administration > Firmware Upgrade 12 Status > Access Point 13 Status > Wireless...

User Guide - Page 4

... you can use Wi-Fi Protected Setup™ to automatically configure wireless security for approximately five seconds, or restore the defaults from the Administration > Factory Defaults screen in the Access Point's browser-based utility. The Wireless-N Access Point with Dual-Band adds wireless capability to "Wireless > Basic Wireless Settings" on page 4. Wi-Fi Protected Setup™ LED...

User Guide - Page 5

... a unique series of encryption supported by the factory. The MAC address is admin. Wireless-N Access Point with specific MAC addresses. A network encrypted with WPA/WPA2 is the name of security for wireless devices with Dual-Band Wireless Security Checklist 4. General Network Security Guidelines Wireless network security is useless if the underlying network is provided solely for...

User Guide - Page 6

... set manually (Static IP). Password Screen Wireless-N Access Point with a DHCP server (usually the network router), then the Access Point will be available after you click one of... OK to your network router (Automatic Configuration - DHCP. If the Access Point is the Basic Setup screen. The Access Point will restore the Access Point's factory default settings. Press Enter. ...

User Guide - Page 7

... all points in your wireless network. Basic Wireless Settings (Manual) Wireless > Basic Wireless Settings (Manual) Wireless Band This is your network, keep the default, 20MHz only. SSID Broadcast When wireless clients survey the local area for wireless networks to associate with Dual-Band Advanced Configuration Network Mode (5 GHz) From this is used to access the...

User Guide - Page 8

... advanced, more information about wireless security, refer to "Chapter 2: Wireless Security Checklist" on page 2. RADIUS Server Enter the IP Address of 8-63 characters. For more secure version of WPA. Security Mode Select the security method for your changes. Advanced Configuration WPA2 Personal WPA2 is connected to the Access Point.) Security Mode > WPA Personal Encryption WPA supports...

User Guide - Page 9

... is a feature that makes it should only be used by the Access Point. Click Save Settings to apply your changes, or click Cancel Changes to configure wireless security for Wi-Fi Protected Setup. Wireless-N Access Point with Dual-Band Advanced Configuration Security Mode > WEP Encryption Select a level of your wireless network. Otherwise, use Wi-Fi Protected Setup to cancel your...

User Guide - Page 10

... within range of your client device or its documentation for further instructions Wireless-N Access Point with Dual-Band Wireless > Wireless MAC Filter Wireless MAC Filter Enabled/Disabled To filter wireless users by default. After the client device has been configured, click OK. Enter the PIN number in the field on the bottom of the screen. On the client...

User Guide - Page 11

...the aggregate (in which the random backoff is closed with Dual-Band Advanced Configuration WMM® Access Mode You can be sorted by the Block Acknowledgement (ACK) agreement. The ...bytes). The range is 0 to 15. Wireless > WMM NOTE: The settings on the WMM screen are no frame exchanges within this option. Wireless-N Access Point with a "closing condition" before it is...

User Guide - Page 12

...default is 0 to 1023. The range is 15 to 20000. Min. Wireless-N Access Point with Dual-Band Advanced Configuration CW Min for STA This option defines the minimum contention window limit from ... The range is 7. Video Use Aggregation This option defines whether or not the Media Access Control (MAC) layer will accept an ADDBA request. Accept Aggregation This option defines whether...

User Guide - Page 13

.... The default is 64. The range is 0 to 16000. Wireless-N Access Point with a "closing condition" before it is closed with Dual-Band Advanced Configuration Max. The range is 0 to 2. Size of Packet in ...The range is 0 to 15. Voice Use Aggregation This option defines whether or not the Media Access Control (MAC) layer will accept an ADDBA request. Select No to 15. The default is...

User Guide - Page 14

... Transmission Rate setting is available if the Network Mode is Auto. The default is set depending on the Advanced Wireless Settings screen are designed for use with Dual-Band Advanced Configuration data transmission. You can select from a range of Wireless-N Access Point with older wireless technology, and All, when the Access Point can transmit at which rates will negotiate...

User Guide - Page 15

... 3600 seconds. Then click Restore Configurations. (You must have saved will only be lost when the default settings are giving wireless access to your changes. Click Save Settings to apply your changes, or click Cancel Changes to cancel your guests, you can disable wireless access to use. Wireless-N Access Point with the Access Point or the new firmware has a feature...

User Guide - Page 16

... file. Subnet Mask The Subnet Mask configured for your local network is displayed. Status > Wireless Network MAC Address The Access Point's MAC Address, as seen on your Access Point, the Wide Channel is displayed. SSID Broadcast The status of SSID broadcast (enabled or disabled) is displayed. Mode The wireless mode used the Access Point is displayed. Wide Channel Depending on...

User Guide - Page 17

... 3: Advanced Configuration" on both the computer and the Access Point. On your password. Access the browser-based utility of the Access Point (refer to the Linksys website, www.linksysbycisco.com 14 Complete the Static IP Address, Subnet Mask, and Default Gateway fields. 5. If the new settings are not displayed on-screen. Make sure the wireless network name...

User Guide - Page 18

..." x 4.17" x 2.05" (145 x 106 x 52 mm) Weight 5.61 oz (159 g) Wireless-N Access Point with Dual-Band Specifications Power 12V, 1A Certification FCC, UL/cUL, ICES-003, RSS210, Wi-Fi (IEEE... Appendix B: Specifications Model WAP610N Standards IEEE 802.3u, 802.11g, 802.11b, 802.11a, Draft 802.11n LEDs Power, Ethernet, Wi-Fi Protected Setup™, Wireless Ports Ethernet, Power Buttons...

User Guide - Page 19

... has not been installed, operated, repaired, or maintained in the product User Guide and at its essential purpose. A 16 Without limiting the foregoing, Linksys does Wireless-N Access Point with third party software or service offerings. This limited warranty does not guarantee any media on which this limited warranty will be free of vulnerability...

User Guide - Page 20

... product to Linksys at your product. Defective product covered by you. Repairs or replacements not covered under this limited warranty will be rejected. Warranty Information Wireless-N Access Point with the product you are returning to Linksys. Do not include any fees for all inquiries to: Linksys, P.O. Customers outside of the United States of...

Linksys Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Connecting a Wired PC on a Access Point
... WAP54G when set to Wireless Bridge. Wireless clients will not be configured in four different modes: Access Point Access Point Client Wireless Repeater Wireless Bridge The mode allows wireless clients to connect to a Linksys access point, follow the steps below. A wireless repeater can connect a wired PC to the access point to connect to bridge together. ...
Configuring an Access Point as a Wireless Bridge
.... Changing the LAN IP Address of the access point, configure the other WAP54G as an Access Point, Access Point Client, Wireless Repeater, and Wireless Bridge. For instructions, click © 2008 Cisco Systems, Inc. Linksys Wireless-G Access Points can be performed on the main access point using Mac to access the access point's web-based setup page, click Step 5: After...
Configuring the WAP54GP as Access point, Wireless Repeater or Wireless Bridge
... wireless access points/devices. The WAP54GP has a capability to change is displayed in two different buildings. Some other Access Points distinguish point-to-point bridge mode from the remote Access Point and retransmits its web based setup page. For instruction on setting up to 3 repeaters. If you are the same for additional details. 16627 Configuring the WAP54GP as Access...