Linksys PSUS4 Support Question
Find answers below for this question about Linksys PSUS4 - PrintServer For USB.Need a Linksys PSUS4 manual? We have 1 online manual for this item!
Question posted by cmprepsol on April 2nd, 2022
Can't Print Through My Linksys Psus4 Print Server In Windows 10 Pro.
I have a Linksys PSUS4 print server (which was working very good on windows 7), but although I have installed Bi admin from my print server's utility and although I can see my USB printer (Epson L310 Series) I can't print in windows 10 pro. It gives me this message "printer not connected"
Current Answers
Answer #1: Posted by akanetuk1 on April 2nd, 2022 11:20 AM
If the PrintServer is not working correctly, follow the advice. If you have trouble printing, make sure that all Ethernet and USB cables connected to the PrintServer are plugged in securely. If the problem continues, refer to
Chapter 4: Bi-Admin Management, page 9. All the LEDs on the front of the PrintServer are off Check the power supply and the power connection.
The PrintServer's Status LED stays lit continuously
Reset the Wireless-Ready PrintServer by unplugging the power supply and plugging it back in or pressing the Reset button on the back of the PrintServer.
I am using DHCP, and the PrintServer gets an IP Address
conflict involving the PrintServer.
If the PrintServer is left on when the DHCP server is turned off, the PrintServer will retain its IP Address without informing the DHCP server. Reset the PrintServer so it will obtain a new IP Address. This problem also arises if you
assigned a static IP Address within the range used by the DHCP server. If so, use another address NOT within the range used by the DHCP server.
The PrintServer's LAN LED is not lighting up.Check your cabling and make sure that the Link LED on your hub or switch is lit up.
A printer connected to the PrintServer cannot print or prints garbage.
Check the following:Cable connection between the PrintServer and1.
printer.The printer driver in the application program or2. Windows matches the printer.Cabling distance is too long if it exceeds 10 feet.3.
The Configuration button on the Printer Status screen in Bi-Admin is grayed out, even though my printer is bi-directional.
The button is unavailable until the printer has finished its
print jobs and sits idle.To start over, I need to set the PrintServer to factory
default.Unplug the power to the PrintServer. Press in the Reset button and plug in the power and continue to hold for 10 seconds. This will return the password and other settings
Chapter 4: Bi-Admin Management, page 9. All the LEDs on the front of the PrintServer are off Check the power supply and the power connection.
The PrintServer's Status LED stays lit continuously
Reset the Wireless-Ready PrintServer by unplugging the power supply and plugging it back in or pressing the Reset button on the back of the PrintServer.
I am using DHCP, and the PrintServer gets an IP Address
conflict involving the PrintServer.
If the PrintServer is left on when the DHCP server is turned off, the PrintServer will retain its IP Address without informing the DHCP server. Reset the PrintServer so it will obtain a new IP Address. This problem also arises if you
assigned a static IP Address within the range used by the DHCP server. If so, use another address NOT within the range used by the DHCP server.
The PrintServer's LAN LED is not lighting up.Check your cabling and make sure that the Link LED on your hub or switch is lit up.
A printer connected to the PrintServer cannot print or prints garbage.
Check the following:Cable connection between the PrintServer and1.
printer.The printer driver in the application program or2. Windows matches the printer.Cabling distance is too long if it exceeds 10 feet.3.
The Configuration button on the Printer Status screen in Bi-Admin is grayed out, even though my printer is bi-directional.
The button is unavailable until the printer has finished its
print jobs and sits idle.To start over, I need to set the PrintServer to factory
default.Unplug the power to the PrintServer. Press in the Reset button and plug in the power and continue to hold for 10 seconds. This will return the password and other settings
Related Linksys PSUS4 Manual Pages
Linksys Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Setting-Up Multiple PrintServers on the Network
... you're unable to print a test page, try to install a generic printer driver that you will detect the PrintServer. For each additional PrintServer that is complete. Connecting the PrintServers to your print server) If you have an active network connection. In this example the SSID "LINKSYS" was used . Step 10: To change the name for your printer is powered on and that... -
Using the PSUS4 Bi-Admin Utility
... Program menu, then BiAdmin Management If the Bi-Admin icon has been created, you want and retype the same password to confirm then click Checking Printer Status The Printer Status option allows you may reset the PrintServer to factory default. BiAdmin: Ensure the Print Server Management Utility - Connected Protocol window appears, make sure that you can double... -
Using the PrintServer's Bi-Admin Utility
... the adapter you to check the name, status, and printing details of the router is compatible with Windows 95, 98, NT, ME, 2000, XP and Novell NetWare. 4135 01/27/2008 10:53 PM Using the PrintServer's Bi-Admin Utility How do I configure my Linksys PrintServer using the Bi-Admin Management Utility, follow the steps below. It is 192.168.1.1. After...
Similar Questions
How To Troubleshoot Linksys 5-port 10/100 Sd205 Switch?
(Posted by pingke 9 years ago)
Where Is The Linksys Sd208 8 Port 10/100 Switch Reset Button?
(Posted by eddcl 9 years ago)
Psus4
labeled a print server, manual says fast downloads. What does it do? Can I remove from wireless netw...
labeled a print server, manual says fast downloads. What does it do? Can I remove from wireless netw...
(Posted by camdenmeadow 11 years ago)
Adding Linksys Sd208 To An Existing Wireless Lan
Can't figure out how add your SD208 to an existing wireless network. Network concists of a Netgear W...
Can't figure out how add your SD208 to an existing wireless network. Network concists of a Netgear W...
(Posted by hyounce 12 years ago)
Sr224g 24-port 10/100 + 1 Port Gigabit + 1 Min... Problem
How do I test if the SR224G 24-port 10/100 + 1 Port Gigabit + 1 min... is working correctly? Some of...
How do I test if the SR224G 24-port 10/100 + 1 Port Gigabit + 1 min... is working correctly? Some of...
(Posted by pebarck 13 years ago)