Home » LiftMaster » Garage Door Openers » LiftMaster SW470

LiftMaster SW470 Support Question

Find answers below for this question about LiftMaster SW470.
Need a LiftMaster SW470 manual? We have 2 online manuals for this item!

LiftMaster Overview Questions Manuals Reviews Videos Research

Question posted by jpgraham741 on April 3rd, 2017

The Measurements Oat The Base For Mounting Is 20.25 Inches My Gate Is 13 Feet 8.

the measurements at the base for mounting is 20.25 inches. My gate is 13 feet 8 inches wide. Will this gate opener work on my swing gate. Gate opener model SW 470

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related LiftMaster SW470 Manual Pages

SW490 GL BOARD Manual - Page 2

... instructions. • These instructions are not intended to list below for Swing and Ornamental Grill Type Gates 8 Warranty Sign Placement 8 INSTALLATION Post Mounting (SW470 9 Pad Mounting (SW470 10 Pad Mounting (SW490 11 Control Arm and Gate Bracket Installation (SW470 12 Control Arm Assembly (SW490 13-14 Manual Disconnect 14 WIRING AVERTISSEMENT Power Wiring Installation 15 On/Off...

SW490 GL BOARD Manual - Page 3

OPERATOR DIMENSIONS AND SPECIFICATIONS MODEL SW470 • 1/2 HP Motor Maximum Gate Weight - 500 lbs. (226.8 kg) Maximum Gate Width - 12 ft. (3.7 m) 6.81" (17.3 cm) 24.25" (61.6 cm) 20" (50.8 cm) 10" (25.4 cm) 14.25" (36.2 cm) 13.38" (34 cm) 13.63" (34.6 cm) 13" (33 cm) MODEL SW490 • 1/2 HP Motor Maximum Gate Weight - 750 lbs. (340.2 kg) Maximum Gate Width - 16...

SW490 GL BOARD Manual - Page 6

... is supplied for installation only on the bottom edge. Pedestrians must take into public access areas. 7. Locate the gate such that transmits radio frequency (RF) signals to promote pedestrian usage. Swinging gates shall not open position. Reference owner's manual regarding placement of non-contact sensor for entrapment protection functions shall be located where the...

SW490 GL BOARD Manual - Page 7

... and installed such that their movement shall not be initiated by a swing gate when in the open position shall not exceed 4 inches (102 mm), measured from the centerline of the pivot point of the gate, refer to ASTM F2200 for exception. 4.1.1.2 Except for additional gate types. 1.2 Gates shall be designed, constructed and installed to not fall over more...

SW490 GL BOARD Manual - Page 9

...fence is critical. 2. pipe (2 req'd.) Concrete pad 16 x 32 minimum Operator 3" O.D. INSTALLATION POST MOUNTING (SW470) 1. Posts should be parallel and square to the gate. Figure 1 18.5" Fence 30" 9.5" 23" Parallel Mount Fence 20" 3" O.D. IMPORTANT NOTE: The distance between mounting posts and the relative location of 3" (7.6 cm) outer diameter heavy walled pipe. Knockouts...

SW490 GL BOARD Manual - Page 10

... run in separate conduit Concrete Pad 2" to pouring concrete. 3. Bolt the (2) pad mount brackets to the fence and the gate is very important that the measurements for operator mounting are taken from the centerline of the fence and of Operator SW470 Perpendicular Perpendicular Mount 1/2" red head bolts or anchors (4 required) Using suitable hardware secure operator to...

SW490 GL BOARD Manual - Page 11

... the operator so that the measurements for operator mounting are taken from the gate installation table. 2. Bolt the (2) pad mount brackets to the bottom of the gate hinge. 3. Pour concrete pad... Pad 18" x 34" min. Figure 2 SW490 GATE OPERATOR INSTALLATION TABLE GATE LENGTH (FEET) 8-9 10-11 12-13 14-15 16-17 18-19 20-21 22 P DIMENSION IN INCHES 21.9 25.3 28.8 32.3 35.7 39.2 42.7 46.1 ...

SW490 GL BOARD Manual - Page 12

...hub assembly to arm hub with spot-faced side up. Arm must swing approximately 2 degrees past straight position (See detail) ADVERTENCIA Crank Extension Extension arm installation detail NOTE: Dotted line indicates straight arm position PRECAUCIÓN GATE BRACKET INSTALLATION (SW470) 1. Model SW470 Top of gate bracket should swivel easily on the operator in a straight line...

SW490 GL BOARD Manual - Page 14

... (Inches) D Dimension (Inches) X Dimension (Inches) Y Dimension (Inches) SW490 Gate Installation Table 8-9 10-11 12-13 14-15 16-17 4.5 4.5 4.5 4.5 4.5 24 30 36 42 48 13 13 13 13 13 25.9 29.3 32.8 36.3 39.7 *25.7 *29 *32.8 *36.9 *41.2 **17 **20.6 **23.8 26.6 29.3 18-19 4.5 54 13 43.2 *45.6 31.8 20-21 4.5 60 13 46.7 *50 34.2 22 4.5 66 13 50.1 *54.6 36.6 All table dimensions are measured...

SW490 GL BOARD Manual - Page 17

... the garage door opener. Repeat Steps 2 and 3 for changing the code setting or replacing the battery. Then follow the steps above to operate at NORMAL position to reprogram each remote control that may cause undesired operation. It must be set for 1/4 second regardless of the length of moving gate or garage door: • ALWAYS keep gate or garage door...

SW490 GL BOARD Manual - Page 29

...inch or as close to the magnets located on the gearbox pulley as possible without fault, check those accessories as well as their wiring. Failure to do not effect the gate. Gate is within 20... of wire removed from the operator and swing the gate open obstruction input has been programmed to function with gate edges not photo eyes. Gate does not Close obstruction input is not ...

SW490 GL BOARD Manual - Page 35

... 19-5040 G202100 20-2101-LD G322100 75-G0089 DESCRIPTION Arm Assembly Kit Arm Channel Arm Extension Gate Bracket Arm Hub Bearing 1-1/4" 1/8" Arm Stop Tinnerman Nut Drive Assembly Kit (Motor Not Included) Shaft Self Aligning Flanged Mount Bearing Sprocket, 40B42 1x1/4" Sprocket, 40B12 5/8" Belt 25" Pulley for all repair part ordering information. SW470 Refer to...

SW490 GL BOARD Manual - Page 37

..., add a K prefix to the model number of your operator. REPAIR PARTS ... box replacement kit, add a K- For example: 20-5752-33 (Motor Number) = K20-575233 (Motor...G0564 K001A5566 12-2002 DESCRIPTION Side Plate Cover Mounting Bracket Frame Assembly Switch Box Cover On/...Kit Rod End Fitting Gate Bracket Extension Arm Galvanized...80-207-25 Gear Reducer Single Swing Collar Double Swing Collar ...

SW490 GL BOARD Manual - Page 39

... 20-3075B-4T 20-3100B-4T 23-3001 23-3005 24-115-1 24-230-5 25-2006 25-2008 25-2010 25-2015 25-2020 25-4001-8K 25-4002-5K 25-4004-K VARIABLE PARTS LIST - MODEL AOMRON MODEL G65MG0204 G65MG0205 G65ME12C5 G65MGR205 G65MGS205 PHOTO-ELECTRIC CONTROLS DESCRIPTION Photocell/Electric Eye - 30' (9 m) Maximum Range SENSING EDGES DESCRIPTION Miller MG020 2-wire electric edge for gates...

SW490 S3 BOARD Manual - Page 1

Installation and Maintenance Instructions Medium & Heavy Duty Swing Gate Operators Models: SW470 SW490 Doc 01-G0665 Rev C

SW490 S3 BOARD Manual - Page 2

... Supplied 4 Model Classifications 4 Specifications 5 Safety Information 6 Safety Instructions 6 Safety Precautions for Swing Gates and Ornamental "Grill Type" Gates 8 Preparing the Installation 9 Pre-Installation Check List 9 Wiring Specifications 9 System Features 10 Installation 12 Post Mount for SW470 Operator Only 12 Pad Mount Installation 13 Control Arm Assembly 14 Gate Bracket...

SW490 S3 BOARD Manual - Page 6

... and Maintenance Manual for the user as well as the bystander. STEP 1: BEFORE INSTALLATION 1 Confirm gate operator model is included in serious injury or death. Gate systems are intended to potential hazards. These instructions are comprised of gate systems must reduce public exposure to highlight certain safety related issues. The design and installation of...

SW490 S3 BOARD Manual - Page 15

...-38) 3/4"-10 HEX NUT (84-RH-75) Figure 9 0 1 -G 0 66 5 F4 4 Model SW 470: Set the control arm stops on the operator in the positions appropriate for desired degree of gate opening. Use the holes that are tightened. Be sure to arm hub with ¼ -20 black plastic knobs provided as shown in Figure 11. Then install...

SW490 S3 BOARD Manual - Page 26

...ALUM. END. 2 BLACK PLASTIC KNOB 1 KEY, 1/4 x 1/4 x 3/4 1 PLASTIC, 6" CARD GUIDE 1 SHOULDER BOLT 82-HN50-20 1 BOLT, 1/2 -13 x 1-1/2 82-PX08-10T (N) 2 PAN HEAD PHILLIPS MS 8-32 x 5/8 82-PX10-04 2 PAN HEAD PHILLIPS 10-32 x ...2 MOUNTING ANGLE 1 WRAPPER, HOUSING 1 BASE PLATE 1 REDUCER BRACKET 1 MOTOR BRACKET 2 SIDE PLATE 1 ARM CHANNEL 1 EXTENSION ARM 1 GATE BRACKET 10-3620 1 S3 MOUNTING BRACKET ...

SW490 S3 BOARD Manual - Page 28

... 2 LIM. Doc 01-G0665 Rev C SWITCH, AUX.OPEN/CLOSE 1 DPST ON/OFF TAG 20A 125277VAC 1 SWITCH BOX 2 ACTUATOR ARM STOP 4 SPACER 2 6-32 HEX NYLON STANDOFF 1 6-32 HEX ALUMINUM STANDOFF 1 GEAR REDUCER REV C 1 TERMINAL BLOCK, 8 POSITION 1 S3 ASSEMBLY PCB TESTED 2 SINGLE SW COLLARS HSW 1 DOUBLE SWING COLLAR 1 HALL EFFECT ASSEMBLY 1 ALARM ASSEMBLY 1 TINNERMAN NUT...