LiftMaster Miracle-One Support Question
LiftMaster Miracle-One Support Question
Find answers below for this question about LiftMaster Miracle-One.Need a LiftMaster Miracle-One manual? We have 1 online manual for this item!
Question posted by charleskoselke on February 25th, 2017
Elite Miracle One Gate Operator Problem
After a rain of one or two days the slave gate responds very slowly to the open position and does not close all the way. The master works fine. After a period of sunshine or even later in the same day after the rain has stopped the slave gate works fine and in conjunction with the master. I have checked batteries and even replacement them. I have pulled new wires to the board on the slave gate and also change the switch harness wire on the slave side. I have reversed the slave and master at the board to see if the next failure is still on the slave or changes to the master side. Has anyone experienced this type of issue and found a solution.
Current Answers
Related LiftMaster Miracle-One Manual Pages
MIRACLE ONE Manual - Page 2
...
UL Audio Alarm Burglar Alarm and Proximity Switch "Gate Opening Inside" Installation of Maglock / Solenoid Relay "Gate Opening Outside" Installation of Maglock / Solenoid Relay Close Delay Option (Master / Second Only) Emergency Key Release Troubleshooting Optional Solar Power Miracle 1 Accessories Miracle 1 Parts Illustration Miracle 1 Parts List / Maintenance Features and Specifications Quick...
MIRACLE ONE Manual - Page 3
... in contact with a separate access opening and closing to be used for exposed rollers. D) The gate must be supplied with the gate while operating the controls. Controls intended to reduce the risk of entrapment. ETL LISTINGS AND INSTRUCTIONS
Installation Instructions Regarding the Gate Operator
A) Install the gate operator only when: 1. The operator is intended for installation only on...
MIRACLE ONE Manual - Page 4
..., such as the one or more contact sensors shall be located where the risk of travel, one that the communication between the sensor and the gate operator is not subjected to the gate operator for each type of the signals are not obstructed or impeded by a moving . 3. Additionally, if the bottom edge of a swing...
MIRACLE ONE Manual - Page 5
... object or stop when an object activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Test the gate operator monthly. Use the emergency release only when the gate is off.
6. ETL LISTINGS AND INSTRUCTIONS
Important Safety Instructions Warning - SAVE THESE INSTRUCTIONS.
4 The entrance is for the...
MIRACLE ONE Manual - Page 6
... is prevented via supervision by persons or vehicles and completes the perimeter of one-to four single family dwelling, or a garage or parking area associated therewith. Vehicular horizontal slide-gate operator (or system) - A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other...
MIRACLE ONE Manual - Page 7
... gate works freely before installing the operator. • Repair or service worn or damaged gate hardware before installing the operator. • Eliminate all gaps in the sliding gate below a 4 foot height that permit a 2 1/4 inch sphere to pass through any location, including the area of the adjacent fence covered when the gate is in the open position. • Install the gate operator...
MIRACLE ONE Manual - Page 8
... the gate is in the open position. • Always be made aware that they must: • Contact a trained gate systems technician to maintain and repair the gate system (End users should never attempt to repair the gate) • Retain and utilize the installation and maintenance manual and safety instructions. • Routinely check all gate operator functions and gate movement...
MIRACLE ONE Manual - Page 9
... local building and electrical codes.
SAVE THESE INSTRUCTIONS.
8 is completely closed. DO NOT install upside down.
To reduce the risk of operator to gate hardware. 5. Always keep the moving gate in the "ON" position, then add a safety loop and center loop. Have a qualified service person periodically inspect and make repairs to water.
DO NOT install on...
MIRACLE ONE Manual - Page 10
...
Back Steel Bracket
(Not Supplied)
(Reinforce if
necessary)
Heavy
Gate Hinge Typical Masonry Column Setup
Steel Top View Plate Post Setup
Gate Hinge Typical Steel
8.5"
25.75"
Post Setup
Out
Gate in Closed Position
7.75"
6"
In
Miracle 1 in Closed Position
90° / 105°
Gate in Open Position Miracle 1 in Open Position
Indexing on central hole in the back steel bracket.
10...
MIRACLE ONE Manual - Page 11
...Steel Bracket (Reinforce if necessary)
Typical Masonry Column Setup
Gate Hinge
Heavy Steel Top View
Plate
Post Setup
Gate Hinge
Typical Steel Post Setup
6"
Indexing on mounting hole in the front steel bracket. 6"
90° / 105°
Gate in Open Position Miracle 1 in Open Position
8.5" This Plate Not Supplied 7.75"
Out
Gate in Closed Position
In
Miracle 1 in
the back steel bracket.
MIRACLE ONE Manual - Page 12
... Miracle 1 horizontally level on a few pickets, or they will not hit the crossbar when in motion.
11 Step 4: Position and level the operator brackets and reinforcement plates. (See next page). Additional reinforcement steel plates may be mounted on top of the crossbar, so the operator will bend.
Do not weld the crossbar on the closed gate...
MIRACLE ONE Manual - Page 15
... Switch Armature
Step 12: Reinstall the operator cover with the limit switches.
Position the outside limit switches of each limit switch
armature. Re-tighten armature screws when gate positions are correct. Slide to adjust. Loosen the 2 screws of each armature to stop the gate in the "full open" and "full closed" positions. PROCEDURE FOR INSTALLATION
Adjusting the Limit...
MIRACLE ONE Manual - Page 20
... area.
8 Ft The ground wire must be directed towards the Elite gate operator. Chamberlain Professional Products is ON, gate will hit vehicle obstructing gate path. Timer On
Set Timer 1 to 60 Seconds
ADJUSTABLE TIMER
...of a direct lightning strike, proper grounding can protect the gate operator in most cases.
Without this path, the intense energy generated by lightning could be located within ...
MIRACLE ONE Manual - Page 22
... #22 will be recognized as "Open Only" command
To provide a close command use #23 and #24. MIRACLE SURGE PROTECTION
Important:
Wiring at #23 and #24 will open cycle, the control board timer must be recognized as shown using velcro. Works as "3 Push Button" control
123
456
789
HELP
0
REV A
Elite Entry Phone
Card Reader
Digital Lock...
MIRACLE ONE Manual - Page 23
...of 4 feet away from open gate
Center Loop
B
Outside
D
C
Safety Loop
A
End of open gate!
For toll free technical support: 1-888-ELITE-10
22 Caution: Distance "E" must have enough separation between loop and gate when opened or closed. Individual circumstances may alter dimensions.
This is largest. Out In
Drawing not to prevent false detection.
SINGLE OPERATOR LOOP SIZE AND...
MIRACLE ONE Manual - Page 26
... Suppressor
Elite Part # A 24
19 20 Com N.O. Gnd +24V
21 22 23 25
Allows gate to automatically open for exiting vehicles.
25 Gnd +24V
23 25
For fail safe operation, connect safety loops in series. Center Loop
Allows gate to stay open when vehicles are obstructing gate path. LOOP DETECTOR WIRING
Safety Loop
Allows gate to stay open when...
MIRACLE ONE Manual - Page 27
Gate in Closed Position
Photocell Gate in Open Position
Potential Entrapment Area (Shaded)
Less than 18" from a wall or any other object or potential entrapment installation. This switch must install a photocell sensor when the gate opens to
(C1) 2 (NC1) 4 5 6 240VDC
15 16 25 23
Black 16 AWG Black 16 AWG
Back
Black 22 AWG Red 22 AWG
26
Front...
MIRACLE ONE Manual - Page 37
... and turn counterclockwise to the full open position 90°.
Full Open Position 90 Degrees
Push or Pull
Lock
Click!
36 Step 3: Re-Lock the operator by turning the key
clockwise while pushing or pulling on the gate until you hear the key release click into place. The operator can resume normal operation as soon as power is...
MIRACLE ONE Manual - Page 44
... - Arm Cover Gaskets (Set) Q310 - UL Audio Alarm
MAINTENANCE
This swing gate operator is designed to be performed by an authorized service technician.
43 Control Board (Master/Second) Q224 - Steel Bracket Mounting Plates (2) Q231 - Bottom Washer and Nut (for Battery Rack) Q230 - Miracle 1 Surge Protection Q311-
MIRACLE 1 PARTS LIST
A BT MIR - DC Solar Power Adapter...
MIRACLE ONE Manual - Page 46
... Input -
Modular Board - Alternate Outputs - Any type of radio receiver, full-control system
"push-open/stop /close ", safety loop, photocell,
telephone entry, and key switch. open manually. Dictates synchronized movement between two gate
operators. Alarm Output - Master/Second: 89 lbs
Torque -
600 lbs. Cycles -
100 / Day. (Consult factory for possible errors or omissions.
Similar Questions
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Gate Will Open But Not Close
Gate will open with remote but only close manually. Radio rec is working(red light and audible click...
Gate will open with remote but only close manually. Radio rec is working(red light and audible click...
(Posted by brettkyle 9 years ago)
My Opener Will Only Open And Not Close.
Gate will open with remote but only close manually. Radio rec is working(red light and audible click...
Gate will open with remote but only close manually. Radio rec is working(red light and audible click...
(Posted by brettkyle 9 years ago)
Elite Miracle One Tech Support
My elite miracle one gate opener is only moving two inches at a time. All circuit lights are reading...
My elite miracle one gate opener is only moving two inches at a time. All circuit lights are reading...
(Posted by Gdkhitt 10 years ago)
Garage Door Opener Will Not Close It Says Power Restored
(Posted by LETcynd 10 years ago)