LiftMaster MHS Support Question
LiftMaster MHS Support Question
Find answers below for this question about LiftMaster MHS.Need a LiftMaster MHS manual? We have 3 online manuals for this item!
Question posted by freedkenneth on May 24th, 2013
Programming Remote.
There is no light on my model adn I can't find any device to program a new remote.
Current Answers
Answer #1: Posted by TommyKervz on May 24th, 2013 11:29 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Greetings - On the link below are Guides available for free download for you system (in case you do not have them) -
http://www.helpowl.com/manuals/LiftMaster/MHS/115728
The one (link) below explaines how you can programme your remote
http://www.ehow.com/m/how_5566187_program-liftmaster-remote.html ;Hope this helps
Related LiftMaster MHS Manual Pages
MGJ User's Guide Manual - Page 2
...
D9
LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN
LEARN STOP CLOSE OPEN LEDD14
1
2
3
4
5
6
7
ADVERTENCIA
PRECAUCIÓN
TO PROGRAM
Photo Eye
Press and hold the LEARN and STOP buttons until the LED goes
out (approximately 3 seconds). The operator will begin closing by any monitored safety devices. NON-MONITORED SAFETY DEVICE
CAUTION
To prevent possible SEVERE INJURY...
MGJ User's Guide Manual - Page 4
... PARTS. Requires LiftMaster monitored safety device.
NOTE: The LED does not indicate that may not cause harmful interference, and (2) this device must accept any combination. TO ...programmed remote controls will light.) 2. Electrical Box
Logic Board
014A1030
J4 C32
TP1 C20
R25
C9
C21
U1
D7
D5
U4 D6
D4
C31
AAUUX AANNTT J2
L5 ^^^^
R27
TTC 1
C18
D14
LEARN STOP CLOSE OPEN...
MGJ User's Guide Manual - Page 5
... Hoist for Model MH
5 Operate the door in case of emergency or power failure. The disconnect chain must be locked in an open . Emergency
disconnect will operate again electrically. To operate the hoist:
1.
MODEL MT/BMT
Emergency Disconnect
CAUTION
To prevent possible SERIOUS INJURY or DEATH from the chain retaining bracket before the door will
Door
open door falling...
MGJ User's Guide Manual - Page 6
Release the disconnect chain or reset the emergency egress device to the operator BEFORE manually operating your door. See Manual Disconnect - Model MH for Model MHS
ADVERTENCIA PRECAUCIÓN
6 ATTENTION Chain Retaining Bracket (with pad locking provisions)
Hoist Chain
Manual Disconnect for Models MJ and MGJ
Electrical Interlock with Hoist Chain (when present) for instructions. A...
MGJ User's Guide Manual - Page 7
...check safety devices. The door should move in a safe manner and how to fully open . 3. Door should close direction.)
4. Allow door to fully open . 3.
Door should stop .)
TEST LIMIT ADJUSTMENT 1. Press OPEN button. (The door should continue closing if in C2 mode. (The door should open.) 2. Press the CLOSE button. The door
AVERTISSEMENT should close . Press remote control button...
MGJ User's Guide Manual - Page 8
...OPERATOR MAKES
Operator requires adjustment
NOISE BUT DOOR DOES
NOT MOVE
DOOR DRIFTS AFTER OPERATOR STOPS
Operator or door requires adjustment
DOOR OPENS/CLOSES Operator requires adjustment TOO FAR
DOOR REVERSES UNEXPECTEDLY
Safety device activated
RADIO FUNCTIONALITY
NO RESPONSE
REMOTE CANNOT BE PROGRAMMED POOR RANGE
Remote control is not programmed Low battery Low battery
Low battery...
MGJ User's Guide Manual - Page 12
...174;SS:
TO
OPEN
Provides protection on doors up
to 30'...hardwired controls.)
ENTRAPMENT PROTECTION DEVICES
Monitored
PRESS
TO
CPS-LN4...OPEN
OPEN
ACCESSORIES
REMOTE CONTROLS 315MHz
371LM
OPEN
1-Button SECURITY✚® Remote Control: Includes visor clip.
373LM
3-Button SECURITY✚® Remote Control: Includes visor clip.
333LM
OPEN
3-Button Tri-Colored Dip Switch Remote...
MJ5011E QuickStart-2008 Manual - Page 1
... of the operator. Or if emergency egress device is used .
When operator is disconnected by slipping the end through the control wiring conduit hole in your door. a Electrical Interlock with drive before the door will disable the electrical controls when the hoist is used , pull handle to Model MH instructions above floor)
Do not insert...
MJ5011E QuickStart-2008 Manual - Page 2
...the LEARN button (LED will become enabled after a preset time, adjustable from 5 to exit programming mode. 6.
Press the desired button on the remote
control until LED flashes rapidly, then release. 4. Press and release the LEARN button. 2. QuickStart for the model MJ/MH/MHS door operator Medium Duty Logic
This QuickStart is running.
1
2
3
4
5
Electrical Box
Logic Board...
MJ5011E Installation-2008 Manual - Page 3
...; Radio receiver: A factory installed radio receiver allows remote controls, keyless entries and other remote command devices to be programmed to the operator.
• Timer To Close: The Timer To Close feature allows the door to Basic Programming Section for rolling sheet doors. Not recommended for use on a standard lift sectional door. Steel
---
20 ga. Steel
20 ga. Steel...
MJ5011E Installation-2008 Manual - Page 4
... Wheel present with model MH only.
7.070" " (17.78 cm)
OPERATOR SPECIFICATIONS
MOTOR
TYPE Limited duty HORSEPOWER 1/2 HP VOLTAGE 115Vac, Single Phase, 60Hz FULL LOAD AMPS 6.0 Amps
ELECTRICAL
OPERATOR VOLTAGE 115Vac, Single Phase, 60 Hz WIRING TYPE C2 (Standard)
B2 Configurable (See Basic Programming Section) CONTROL WIRING 16-22 AWG
MECHANICAL
DOOR SPEED Approximately...
MJ5011E Installation-2008 Manual - Page 5
...
Output Shaft
Right Handed Operator
ADVERTENCIA
5
ADVERTENCIA
AVERTISSEMENT
HAANDTINTGEIDNENTTIIFOICNATION
For MH and HMS models with : Master links (2),
wall bracket (1), Fastener Bag (1)
WARNING
PREPARATION
WARNING
PREPCARAINUG TYOIUORNDOOR
The manufacturer recommends 3' (91.4 cm) of clearance in the door opening, hook the chain off to install the operator.
The handing...
MJ5011E Installation-2008 Manual - Page 9
...)
Chain Retaining Bracket (with manual hoist to electrically disable the operator controls. Operator
Operator
8 INSTALL MANUAL DISCONNECT SYSTEMS
The MHS operator includes both a floor level disconnect chain to disconnect the door from the door operator and a disconnect chain with pad locking provisions)
B Wrap hand chain around hand chain wheel and through chain guide...
MJ5011E Installation-2008 Manual - Page 14
... make contact with an obstruction while the door is closing , the door will stop and typically reverse to the full open position. See Optional Safety Device Configurations for wiring information.
Safety Edge
Photo Eye
Sensing Edge
14 If an obstruction breaks the light beam while the door is closing , the door will stop and typically reverse to...
MJ5011E Installation-2008 Manual - Page 16
... Auxiliary Antenna Connection
LED
Field Wiring Terminal Factory Wiring Connector
FUNCTION Open Door Close Door Stop Door Programs the remote controls and performs additional programming Programs the Timer to Close Primary Antenna For use with external antenna kit EXT-ANT. Not Provided Used during programming and diagnosing error codes Field wiring connections Factory wiring harness connection...
MJ5011E Installation-2008 Manual - Page 19
... will become active after a preset time, adjustable from the open limit after completion of timer setting.
Release both buttons.
3. Press and release the TTC button to program additional buttons. TO PROGRAM
1.
All programmed remote controls will light). 3.
Press and hold the desired button of this device must accept any combination. Press and release the LEARN button...
MJ5011E Installation-2008 Manual - Page 20
... for adjustment of the limits. Press remote control button. 2. Allow the door to fully open . 3. Press remote control button. 4.
TEST THE SAFETY DEVICES (IF INSTALLED) 1. Open the door. 2.
Door should close if photo eyes are working properly. Press OPEN button. (The door should close
direction.) 4.
AVERTISSEMENT If door did not reverse from electrocution, disconnect...
MJ5011E Installation-2008 Manual - Page 21
...an open door falling rapidly and/or unexpectedly. • NEVER use emergency disconnect ONLY when door is used . Pull the disconnect chain (sash chain) to operate the door again electrically. The disconnect chain may now be released from the door operator.
1. Chain Keeper
AVERTISSEMENT (with manual hoist to the operator BEFORE
manually operating your model operator.
MODEL MHS...
MJ5011E Installation-2008 Manual - Page 22
... button is not stuck.
TTC NOT FUNCTIONING A) Monitored Safety Devices
➤ Check all connections.
B) Remote control not compatible ➤ Obtain qualified LiftMaster remote control device.
The LED will be re-enabled.
OPERATOR MOVES IN OPEN and CLOSE button wiring ➤ Check 3-button control wiring. DOOR OPENS/CLOSES Limits not adjusted properly TOO FAR
➤ Adjust...
MJ5011E Installation-2008 Manual - Page 31
...-8202
WIRE 65-7WIREL
PRESS TO
R ING
21-2LM
Commercial Protector System: OPEN
Provides protection on doors up to 45' wide. OPEN CLOSE
PRESS TO
R ING
OPEN
ACCESSORIES
REMOTE CONTROLS 315MHz
371LM
OPEN
3-Button SECURITY✚® Remote Control: Includes visor clip. OPEN
CLOSE
31 OPEN CLOSE
Antenna: External kit for maximum radio receiver range. WPB1LM
WPB3LM
WKP5LM
123...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 8 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Opening Closeing
Door goes up just fine but push the close button door will not go down..if u tap on the side of the ...
Door goes up just fine but push the close button door will not go down..if u tap on the side of the ...
(Posted by Anonymous-146137 9 years ago)
My Door Stopped Shutting Completely. How Do I Adjust It?
My door (MH5011R) stopped shutting completely. It remains about 2 inches above the ground. How do I ...
My door (MH5011R) stopped shutting completely. It remains about 2 inches above the ground. How do I ...
(Posted by brodgers80406 10 years ago)
Closing Door
Why do I have to hold close button to close door? What Em I doing wrong
Why do I have to hold close button to close door? What Em I doing wrong
(Posted by glen7010 11 years ago)