Kyocera FS 1128 Support Question
Kyocera FS 1128 Support Question
Find answers below for this question about Kyocera FS 1128 - MFP.Need a Kyocera FS 1128 manual? We have 1 online manual for this item!
Current Answers
Related Kyocera FS 1128 Manual Pages
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 3
.../60 Hz
CAUTION: Be sure to provide enough space around machine.
SETUP GUIDE
3
Prolonged use
without sufficient clearance may cause overheating. If the machine is FS-1128MFP, the modular cord with the attached ferrite core is enclosed. IMPORTANT: Place the machine in a stable position.
Unpacking
1 Unpack the machine and all its...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 6
...size of the paper.
4 Fan the paper, then tap it on a level surface to avoid media jams or skewed printing.
5 Place the paper in on the release buttons and sliding the guides to fit the width of the paper. Preparations...length by pressing in on the release buttons and sliding paper stopper to be printed downward, so that the leading edge is aligned against the paper stopper.
6
SETUP GUIDE
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 7
... until it stops.
These cables are sold separately. Preparations
Connecting Cables
1 Turn the power switch off (O).
2 Connect the machine to the PC or your network device. When using the network interface, remove the cap. SETUP GUIDE
7 IMPORTANT: Do not exceed the upper limit of the cassette.
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 8
this will begin replenishing the toner; Connecting Modular Cords (FS-1128MFP only)
1 Turn the power switch off (O).
2 Be sure to warm up.
The machine begins to loop the cord three times through the ferrite core.
8
...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 9
...
5 Turn the power switch on the message display.
If the mache is first installation, it will take approximately 15 minutes. Replacing the Operation Panel Language Sheet
1 Remove the attachements as shown in the figure.
B
4 Route the cords as shown. The machine begins to copy will appear on (|). SETUP GUIDE
9 Then, connect...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 10
Preparations
2 Remove the plastic cover and the operation panel language sheet.
3 Insert the desired operation panel lanhuage sheet and the plastic cover as shown.
4 Fix the attchements as shown.
10
SETUP GUIDE
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 17
...current status of the items displayed on the left to view and set as the WSD device name. Specifies the communication rate from which you have completed these settings in order to...properly register the content of the machine and make the settings that are required for the printing system network component.
The default Administrator password is factory-set values for that category.
4 ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 18
... (32-bit) numbers separated by dots, e.g. 192.168.110.171.
Assigns an IPv6 address to the size of the hosts or network with which the print system is recommended that the machine be completed.
To use the e-mail function, the scanner system needs connection to use RA to obtain IPv6 IP...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 20
... entered correctly for SMTP authentication. Accessing COMMAND CENTER
Item Sender Address
Signature Domain Restriction
Description
Enter the E-mail address of the person responsible for the printing system, such as a file in a desired folder on your PC. The sender address must consult the administrator to the Windows User logon on the scanner...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 29
... Mode
Express Mode
In Express Mode, the installer automatically detects the machine when it is turned on . If the installer does not detect a print system, check that the print system is connected via USB or a network and that it is connected via a network. Proceed to be the name displayed in the Printer...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 30
...version.
30
SETUP GUIDE Custom Mode
Use Custom Mode if you can also specify the device settings after you click Finish, you want fonts installed on your computer to be installed ...the instructions in the install wizard window, select the software packages to Custom Installation in the print system. For details, refer to be replaced, select Custom Mode and deselect the Fonts checkbox ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 31
... the components to add the installed printer driver. SETUP GUIDE
31
Next, specify the print settings. This completes the printer driver installation. IMPORTANT: In the Authenticate screen, enter... software. If a USB connection is automatically recognized and connected.
8 Open System Preferences and click Print & Fax.
9 Click the plus symbol (+) to be installed.
If an IP or AppleTalk ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 36
Rev.1 2010.1 Printed in China 302H956021
Similar Questions
Kyocera Fs 1128
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
(Posted by spaffordb 11 years ago)