Kenwood KDC-X695 Support Question
Kenwood KDC-X695 Support Question
Find answers below for this question about Kenwood KDC-X695.Need a Kenwood KDC-X695 manual? We have 1 online manual for this item!
Question posted by DIAZFAMILY07 on November 18th, 2014
My Kdc-x695 Won't Work It Just Say's Protect When I Turned On First Time I Had A
The person who posted this question about this Kenwood product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by BusterDoogen on November 18th, 2014 7:34 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.
“PROTECT” appears and no operations can be done.
Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest service center.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Kenwood KDC-X695 Manual Pages
Instruction Manual - Page 1
... COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to the model and serial numbers whenever you obtain the best performance from your Kenwood product at www.Kenwoodusa.com
© 2010 Kenwood Corporation All Rights Reserved.
Model KDC-BT648U/ KDC-X695/ KDC-X395/ KDC-348U Serial number
US Residents Only
Register Online
Register your...
Instruction Manual - Page 3
... names are owned by Kenwood Corporation is airconditioned, moisture may cause an accident. ■ Condensation: When the car is under license. Please note that they work with your model and in damage to the KTC-HR300/ KTCHR200/ KTC-HR100TR, sold separately.
■ "Made for iPod" and "Made for the operation of...
Instruction Manual - Page 6
RDS: Radio Data System service is turned on. TI: Traffic Information function is available. EQ: [SYSTEM Q] is set to an EQ mode ... sensor ■ Do not expose to bright sunlight.
The illustration and button names used for the difference: KDC-BT648U/ KDC-X695
KDC-X395/ KDC-348U
Display window
USB terminal Auxiliary input jack
Slide open the cover
6 English ST: A stereo broadcast is in...
Instruction Manual - Page 7
...turned on . ■ Turns off if pressed and held
while in clock display screen. Enters [FUNCTION] settings. on the main unit will also exit from setting mode. KDC-BT648U/ KDC-X695... only:
■ Enters Bluetooth mode. (page 15)
■ Press to answer an incoming call.
- ■ Enters Bluetooth easy pairing mode if pressed and held. (page 18)
KDC-X395/ KDC...; Turns on...
Instruction Manual - Page 13
... enter
[FUNCTION] mode. 2 Turn the volume knob to select
[SETTINGS], then press to enter. 3 Turn the volume knob to finish the procedure.
KDC-X395 / KDC-348U Press and hold iPod repeatedly...
MPLIST YES: Deletes the saved My Playlist. ; About Audio file ■ Playable Audio file
: MP3 (.mp3), WMA (.wma) : AAC-LC (.m4a) KDC-BT648U/ KDC-X695 only ■ Playable disc media: CD-R/RW/ROM &#...
Instruction Manual - Page 15
KDC-BT648U / KDC-X695 1 Press and hold for the ...turn on the power. 2 Start registering this unit. ■ For details on
Continued to answer an incoming call .
■ Press and hold to a cell-phone, with a cell-phone operation. 6 The receiver is connected to enter easy pairing
mode "PAIRING" is displayed. 2 "SEARCHING" is displayed during paring, see (page 22). KDC-BT648U/ KDC-X695...
Instruction Manual - Page 16
... in advance. "PHONE BOOK": Calling a Number in the Call Log - Making a Call 1 KDC-BT648U / KDC-X695
Press to (page 19). OF: Office ; Refer to enter Bluetooth mode. "OUTGOING"/ "INCOMING"/ "MISSED
CALLS": Calling a Number in the
Phone Book - the Bluetooth device. Dial a Number 2 Turn the volume knob to select "NUMBER
DIAL", then press to enter...
Instruction Manual - Page 17
...; Audio sound is displayed. When a beep is displayed. Refer to start voice recognize. 4 "PB NAME" is heard, say the name within 2 seconds. During a Call Disconnecting a Call
KDC-BT648U / KDC-X695 Press...You can make a call. Receiving a Call Answering a Phone Call
KDC-BT648U / KDC-X695 Press . Make a Voice Dialing Call 2 Turn the volume knob to select "VOICE
RECOG", then press to enter...
Instruction Manual - Page 18
... Incoming Call
with up to 25 (KDC-BT648U/ KDC-X695)/ 32
(KDC-X395/ KDC-348U) digits can be registered for ...time, registering a cell-phone 2 "SEARCHING" is displayed. ■ Any of characters.)
Using the remote controller (RC-405)
Making a call . Bluetooth Setup
Preparation : KDC-X395/ KDC...search is completed, "FINISHED" is displayed. 3 Turn the volume knob to select a cellphone name, ...
Instruction Manual - Page 19
...
English 19 If "PAIRING OK" is displayed, registration is displayed. 6 Turn the volume knob to select a Bluetooth device name, press to enter Bluetooth mode.
By operating the Bluetooth device, register the hands-free unit (pairing). You can change this unit 1 KDC-BT648U / KDC-X695
Press to confirm. Refer to exit easy pairing mode. When...
Instruction Manual - Page 20
... device 1 KDC-BT648U / KDC-X695
Press to enter Bluetooth mode. KDC-X395 / KDC-348U Press and hold the volume knob to enter
20 English
Bluetooth mode. 2 Turn the volume knob to select
[SETTINGS], then press to enter. 3 Turn the volume knob to select
[PAIRING], then press to enter. 4 Turn the volume knob to select [PHONE
SELECT] or [AUDIO SELECT...
Instruction Manual - Page 21
... tag is not registered for selection. ■ Repeat step 3 until the desired item is heard, say a voice tag within 2 seconds. Bluetooth Setup 1 KDC-BT648U / KDC-X695
Press to next page
English 21 KDC-X395 / KDC-348U Press and hold the volume knob to enter Bluetooth mode. 2 Turn the volume knob to select [SETTINGS], then press to enter...
Instruction Manual - Page 22
...KDC-X695 only
ON *: Automatically reconnects the selected Bluetooth device when radio wave becomes strong enough,
even after lapse of the built-in microphone volume.
BT HF /
FRONT *: Outputs audio from the all
BT HF/AUDIO... required when registering this function is turned ON, the Bluetooth device is reconnected if it is disconnected. ; ALL: Outputs audio from the front-left and front...
Instruction Manual - Page 23
... message, turn the volume
knob. ■ To return to the message list, press the
volume knob. 5 Hold to transmit the
SMS using Bluetooth. Display the SMS
¤
To prevent car accidents, the driver should not read and unread short messages can be required.
Continued to enter Bluetooth mode.
KDC-BT648U/ KDC-X695 Press to...
Instruction Manual - Page 28
... Press the volume knob to enter [FUNCTION] mode. 3 Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter. 4 Turn the volume knob to make a selection, then press to ...KDC-X695/ KDC-X395 only:
MID CTR FRQ 0.5K/ 1.0K/ 1.5K/ 2.0K *: Selects the center frequency. BASS BOOST
B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; SUBWOOFER SET ON *: Turns ...
Instruction Manual - Page 30
...screw (for Nissan cars 4) G Round head screw (for Toyota cars 4) H Microphone (3 m) (KDC-X695 only 1)
Basic procedure
1 Remove the key from the ignition switch, then disconnect the · ... after installation.
■ If the power is not turned ON ("PROTECT" is 30° or less.
■ If the... may have been activated. on the car are working properly.
■ Mount the unit so that in...
Instruction Manual - Page 31
...
The above maximum communication range (10 m) is an obstacle between this work to select the "BT AUDIO EXT". - Selecting Bluetooth Audio source
Press SRC to professionals. For safety's sake, leave this unit...this unit in the console of 10 m (30 ft). About Bluetooth unit (Optional: KDC-X395/ KDC-348U) ■ This unit supports KCA-BT300 or KCA-BT200. ■ Plugging a KCA-BT300...
Instruction Manual - Page 32
...Fuse (10A) Wiring harness D
Rear output
R
L Front output
Sub Woofer output
Microphone H (KDC-X695 only)
White White/Black
Gray Gray/Black
Green Green/Black
Purple Purple/Black
To front left speaker...) matches your navigation manual. (Connect to the antenna control terminal in the vehicle.
KDC-X395/ KDC-348U only)
To use the steering wheel remote control feature, you need to the ...
Instruction Manual - Page 34
..."PROTECT" does not disappear, consult your nearest service center. If the condition did not improve, turn...34 English The unit does not work at several
positions using tape or ....
Reinsert the disc properly. Installation the Microphone Unit (KDC-X695 only)
1 Check the installation position of the
microphone... / The CD is playing an unsupported audio file. Connect the antenna firmly. / Pull...
Instruction Manual - Page 37
...;1 dB): 20 Hz - 20 kHz Total harmonic distortion (1 kHz): KDC-X695/KDC-X395: 0.008 % KDC-BT648U/KDC-348U: 0.01 % Signal-to-Noise ratio (1 kHz): KDC-X695/KDC-X395: 110 dB KDC-BT648U/KDC-348U: 105 dB Dynamic range: 93 dB AAC decode: AAC-LC ".m4a" files (KDC-BT648U/ KDC-X695 only) MP3 decode: Compliant with MPEG-1/2 Audio Layer-3 WMA decode: Compliant with Windows Media...
Similar Questions
Kenwood Ddx418 Is Going Off N On. Also Buttons Don't Work Just Tscreen Work
(Posted by jadonledbetter 3 years ago)
Dpx308u Is Stuck On Demo.and All Buttons Don't Work ..just Stays On Demo
(Posted by louie812 4 years ago)
My Ken Wood Kdc X695 Only Lets You Turn The Valume Up And Don't!!
So my kenwood x695 only lets you turn the valume up and down and that's it nothing else any suggesti...
So my kenwood x695 only lets you turn the valume up and down and that's it nothing else any suggesti...
(Posted by Devils2412 9 years ago)
Volume Knob On My Kenwood Kdc-x695 Quit Working
My volumer knob on my Kenwood KDC-695 stoped functioning all together. So I reset my stereo. Now I'm...
My volumer knob on my Kenwood KDC-695 stoped functioning all together. So I reset my stereo. Now I'm...
(Posted by yezzireee13 9 years ago)