Husqvarna T540 XP Support Question
Husqvarna T540 XP Support Question
Find answers below for this question about Husqvarna T540 XP.Need a Husqvarna T540 XP manual? We have 2 online manuals for this item!
Question posted by tkrotz on September 23rd, 2014
Can I Increase My Husqvarna 365 Saw Cc Displacement For A Rebuild?
I need to rebuild the saw and would like to increase power if possible.
Current Answers
Related Husqvarna T540 XP Manual Pages
Owners Manual - Page 2
... the label.
Max. Choke.
Never operate a chain saw .
Careless or improper use can be used to operate the chain saw holding it with any object. May cause serious personal injury...
Chain brake, activated (right) Chain brake, not activated (left)
2 - Chain type Husqvarna H37
Working position.
Both of the operator′s hands must be dangerous! KEY TO SYMBOLS...
Owners Manual - Page 3
...and adjusting oil flow.
EPA III
The Emissions Compliance Period referred to on your chain saw is required. The engine exhaust from this product contains chemicals known to the State
of the .... English - 3 WARNING! Protective goggles or a visor must be engaged when the chain saw :
Switch off the engine before carrying out any nonroad engine repair establishment or individual.
Owners Manual - Page 4
... avoid kickback 31 MAINTENANCE General 32 Carburetor adjustment 32 Checking, maintaining and servicing chain saw safety equipment 32 Muffler 34 Starter 34 Air filter 36 Spark ... or colder 38 Maintenance schedule 39 TECHNICAL DATA Technical data 40 Guide bar and saw chain combinations 41 Saw chain filing and file gauges 41
FEDERAL AND CALIFORNIA EMISSIONS CONTROL ...
Owners Manual - Page 5
... a Husqvarna product. Husqvarna AB has a policy of continuous product development and therefore reserves the right to properly maintain and use it will also know how to modify the design and appearance of muskets.
In 1956, the first motor driven lawn mowers appeared, followed by chain saws in the world of forest and garden products...
Owners Manual - Page 6
...23 4
5
20
14 6
21 22
25 24
23
27
13
7
12 11 10 9 8
26
What is what on the chain saw?
1 Front hand guard 2 Stop switch 3 Information and warning decal 4 Top handle 5 Filter cover 6 Choke control 7 Rope eyelet 8... handle 12 Starter 13 Front handle 14 Chain oil tank 15 Bar tip sprocket
28
29
16 Saw chain 17 Guide bar 18 Throttle trigger 19 Throttle lockout 20 Belt eyelet 21 Clutch cover 22 ...
Owners Manual - Page 7
... permanent hearing impairment. English - 7
authorized accessories or replacement
parts. When using a new chain saw
• Please read and
understand the contents of a damaged
muffler. Do not attempt...some
circumstances interfere with active or
passive medical implants. WARNING!
A chain saw is correctly fitted and adjusted. WARNING! Avoid contact with medical
...
Owners Manual - Page 8
...Never use common sense
It is designed for tree service is not possible to asphyxiation or
carbon monoxide poisoning. See instructions under the heading "...be beyond your dealer or us if you consider to contact your capability. This chain saw
chain increases the risk of bar and saw for pruning and dismantling standing tree crowns. You should consult an expert before continuing. ...
Owners Manual - Page 9
...and working techniques and who are explained. See instructions under the heading, What is an increased risk of movement.
Another important feature is designed to a servicing
dealer for tree surgery...
techniques which must be activated manually (by your machine. If
your saw to stop the chain if you need them . WARNING! Help prevent forest fires. For this section...
Owners Manual - Page 10
... should also maintain a firm grip of the chain brake impossible. for example, when the saw is farthest away from rotating.
• Use the chain brake as a "parking brake" when starting... hand guard backwards, towards the front handle.
• Kickback can be engaged when the chain saw chain is
Will my hand always activate the chain brake during a kickback? With this happens you...
Owners Manual - Page 11
... a kickback? If the chain brake is blunt or faulty (wrong type or badly sharpened) will increase the vibration level.
Second, it would activate all the time which would be in cold
temperatures.
...in people who have enough time to slow down and stop the chain before the chain saw hits you and proper working instructions). Only you .
GENERAL SAFETY PRECAUTIONS
Will my inertia ...
Owners Manual - Page 12
... chain combinations we recommend, and follow the filing
instructions. Only use a saw
chain increases the risk of the bar never touches anything. See instructions under the heading Technical ... zone of kickback! This also applies during and after use cutting equipment recommended by Husqvarna. Be aware of links, which can cause extremely serious
injuries.
Guide bar
The ...
Owners Manual - Page 14
...14 - This recommendation assumes that are recommended for your chain saw and file the teeth on the package for the ... you sharpen the cutting tooth (A) the depth gauge setting (C) will need a flat file to file off the tip...too large! sharpening instructions considerably
increases the risk of the cutting teeth is correctly tensioned. GENERAL SAFETY PRECAUTIONS...
Owners Manual - Page 20
...in damage to suit the air temperature.
• In temperatures below .
Ethanol fuel
HUSQVARNA recommends commercial available fuel with good adhesion characteristics.
20 - Then add the entire amount... during the first 10 hours. Environment fuel
HUSQVARNA recommends the use oil of oil to a high engine temperature and increased bearing load, which is obtained.
This can occur....
Owners Manual - Page 27
...
1 Make sure the cutting equipment will need to take steps to hold the saw with the right hand on either the left or right of the saw away from the body while holding the ...close into vertical stems with a pushing chain increases the risk of the saw onehanded.
Gaining a good footing at the tip of the chainsaw guide bar
• 'hold the saw with one -handed use full throttle when ...
Owners Manual - Page 32
...chain rotates while
!
The chain saw 4-cycles.
• Regularly check that reduce harmful emissions.
AutoTune is controlled by an authorized service workshop.
Conditions
NOTE! More extensive work on the machine requires special training. Carburetor adjustment
Your Husqvarna product has been designed and manufactured to contact our servicing dealer. Engine...
Owners Manual - Page 36
... consumption. • Remove the air filter after about a month in operating problems and starting difficulties. A HUSQVARNA chain saw can be cleaned more thoroughly by washing it . These factors cause deposits on power, difficult to working conditions, weather, season, etc. English
When refitting make sure that hold...
Owners Manual - Page 37
... blocked cooling system results in the machine overheating which causes damage to increase the working temperature as low as possible the machine is adjustable.
When lubricating, remove the clutch cover by ...making adjustments.
Be sure to refill the oil tank every time when refueling the saw on the starter to the piston and cylinder.
The engine must be stopped
! This ...
Owners Manual - Page 40
...000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks, lb/kg Chain/bar Standard bar length, inch/cm Usable...teeth Chain speed at max. TECHNICAL DATA
Technical data
Motor Cylinder displacement, cu.in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/hp @ rpm Emissions Durability Period according to California Air...
Owners Manual - Page 41
... listed below.
As we are type approved for the Husqvarna chainsaw model T540XP.
This chainsaw model equipped with the combinations of recommended cutting equipment for your chain saw chain combinations. We recommend to ANSI B175.12000 (Gasoline Powered Chain Saws - Recommended cutting equipment for Canada
Following is determined by either of a solid bar.
For...
Owners Manual - Page 42
... only). MANUFACTURER′S WARRANTY COVERAGE
The emissions control system is subject to 80 cc, only the fuel tank is warranted for two years. OWNER′S WARRANTY RESPONSIBILITIES...be warranted for the remaining warranty period. In U.S. Where a warrantable condition exists, Husqvarna Forest & Garden will be designed, built, and equipped to service the subject engines.
If you ...
Similar Questions
Piston And Cylinder Size
What size piston does the 540xp have? Also the size of the cylinder ? I'm looking to getting it hone...
What size piston does the 540xp have? Also the size of the cylinder ? I'm looking to getting it hone...
(Posted by Andrewrivera1123 1 year ago)
Ignition Coil Gap K970 Rescue Saw
ignition coil gap on a k970 rescue saw
ignition coil gap on a k970 rescue saw
(Posted by broachri 7 years ago)
Husqvarne K 970 Cut Off Saw
saw refuse to starttake out spark plug and pore half cap mix gas and it startplease help.
saw refuse to starttake out spark plug and pore half cap mix gas and it startplease help.
(Posted by recycleit 9 years ago)
Have The K760 Concrete Saw. Wont Start,
have the k760 concreate saw , wontstart ive found oil in the de compreshion switch bore, and spark p...
have the k760 concreate saw , wontstart ive found oil in the de compreshion switch bore, and spark p...
(Posted by nevjones2010 9 years ago)
Husqvarna K760 Saw
Saw runs but dosnt rev up properly checked fuel filter in tank use husqvarna oilguard In mix
Saw runs but dosnt rev up properly checked fuel filter in tank use husqvarna oilguard In mix
(Posted by Ctrav73 9 years ago)