Husqvarna K 970 Support Question
Husqvarna K 970 Support Question
Find answers below for this question about Husqvarna K 970.Need a Husqvarna K 970 manual? We have 2 online manuals for this item!
Question posted by recycleit on May 27th, 2015
Husqvarne K 970 Cut Off Saw
saw refuse to starttake out spark plug and pore half cap mix gas and it startplease help.
Current Answers
Answer #1: Posted by freginold on May 28th, 2015 3:38 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,895
Member since:
December 20th, 2011 Points: 23,253,895
Generally when that happens, the gas isn't getting to the combustion chamber so it's either a problem with the fuel line or the carb. Rebuilding and cleaning out the carb is the most likely solution. It could also be stale fuel in the gas tank, unless the gas you poured directly into the engine was from the gas tank. Try cleaning and rebuilding the carb first.
---------------------
If this answer helped you to solve your problem, please let us know by clicking on the "Helpful" icon below. If your question wasn't answered to your satisfaction, feel free to resubmit your question, with as much information as possible so that we can provide a more complete solution. Thank you for using HelpOwl!
Related Husqvarna K 970 Manual Pages
Owners Manual - Page 1
RIDER 970
RIDER 850
RIDER 850
Rider 850 HST Rider 970 HST
Operator´s manual
Please read these instructions carefully and make sure you understand them before using the machine.
101 89 36-26
Owners Manual - Page 3
... other than described in this manual contact an authorised dealer for adjustment of cutting height 10 Seat,Rider 850 HST 10 Seat, Rider 970 HST 11 Fuelling 11 Driving 12 Before starting 12 Starting the engine 12 Driving the machine 14 Cutting tips 15 Stopping the engine 16 Maintenance 17 Maintenance schedule 17 Dismantling of...
Owners Manual - Page 4
... the machine and in the operator's manual. Drive very slowly without the cutting unit. Risk that you know what they mean. Starting instructions Read the instructions Check the engine's oil level Check the hydrostat's oil level Lift up the cutting unit Put the gear shift/hydrostat pedal in neutral Brake If the engine...
Owners Manual - Page 5
...8226; Do not cut in the area before starting it.
WARNING!
Always wear heavy-duty shoes, preferably toe-capped.
• Never wear loose fitting clothes which can cut off the blades ...visor during reversing.
• Keep an eye on the machine before starting the machine. RIDER 970
Read the instructions before starting to stop the engine and take out the keys before leaving the...
Owners Manual - Page 6
... drive smoothly and slowly on wheelweights or counterweights to what you feel uncertain avoid cutting it . Be extra careful when loading it is the most serious risk that ...c.
RIDER 850
a. Be careful when reversing. Avoid sudden changes of speed or direction.
• Avoid starting or stopping on a trailer or truck.
• Be careful when pulling a load or using heavy equipment...
Owners Manual - Page 7
... room or where there is running. b.
RIDER 970
Never fill up with fuel indoors. The machine ....
• Do not cut close to corners, bushes, trees or other objects which can emit sparks.
• Check the ... the fuel system the engine must not be started until this purpose. Let the engine cool before...so that children stay where you last saw them.
• Keep children away from...
Owners Manual - Page 8
... gas is in the battery. Allow the machine to cool before placing it in the vicinity of naked flames or sparks. RIDER 970
...• Never drive the machine in it has evaporated before starting the engine. Check the parts regularly and if necessary replace them... an object can cause cutting injuries. Keep the machine clean from grass, leaves and other refuse which fastens in an...
Owners Manual - Page 9
... of the controls
1. Ignition lock 2. Adjustment of drive
7 English - respectively.
Lifting lever, cutting unit 5.
Lever for reversing. Lever for parking brake 9. PRESENTATION
Presentation
These instructions describe two machine models, Rider 850 and Rider 970. Fuel tank cap 11. Both models are fitted with engines from the engine is handled by a hydrostatic...
Owners Manual - Page 11
... 850
In the standard version Rider 970 HST is fitted with a cutting unit which cuts up and the blades stop rotating (transport position). If the lever is returned to set the cutting unit in the lawn.
Lift lever for a small mound in transport or cutting position. The diagram shows a Rider 970 with rear ejection, i.e. The lever can...
Owners Manual - Page 12
The seat can be adjusted to 9 different positions (4-90 mm, 45-80 mm Bioclip). PRESENTATION
Lever for adjustment of cutting height
With this lever the cutting height can also be adjusted lengthways. Seat, Rider 850 HST
The seat has a jointed attachment on the front edge and can be moved forwards or ...
Owners Manual - Page 13
... and can also be tipped forward. Observe care and fill up with the knobs. English - 11 The seat can be adjusted lengthways. PRESENTATION
Seat, Rider 970 HST
The seat has a jointed attachment on at least 92 octane leaded or unleaded petrol/gasoline (not oil...
Owners Manual - Page 14
This is done as follows:
• Press down .
2 1
Cold engine:
3. Apply the parking brake. Adjust the seat to locked position (transport position).
2. Starting the engine
1. Lift up the cutting unit by pulling the lever backwards to the required position.
Push the throttle control to position 3 (choke
position). In this position the engine receives...
Owners Manual - Page 15
.... Never run the starter for more than about 10 seconds before trying again.
6.
Turn the ignition key to neutral position. If the engine does not start position. Push the throttle control to full throttle.
! WARNING! The exhaust fumes contain toxic carbon monoxide. IMPORTANT INFORMATION Do not run the engine indoors, in...
Owners Manual - Page 17
... throttle until the cutting unit has been lowered to avoid collision.
• Start with a high cutting height and reduce down until the required cutting result are obtained.
• The cutting results are achieved...inferior mowing results.
• Avoid mowing a wet lawn.
Push in the lock button on both front wheels (60 kPa).
4. Cutting tips
• Localise and mark stones and other ...
Owners Manual - Page 19
...; The engine is switched off.
• The parking brake is applied.
• The ignition key is removed.
• The cutting unit is disengaged.
• The ignition cable is removed from the plug. For the items which should be conducted twice a week. 4) Conducted by authorised service workshop.
r
Check the transmission's oil level
21...
Owners Manual - Page 25
...'s ground pressure is conducted as follows: 1. RIDER 850
English - 23 MAINTENANCE
Checking and adjustment of the cutting unit's ground pressure Rider 970
To achieve the best cutting results the cutting unit should be placed between 12 and 15 kg. If necessary a block can be between the frame and scales so that it . Adjust the...
Owners Manual - Page 26
...hood.
1 32
24 - Release the strut by
shortening the lift-strut. Vertical adjustment of the cutting unit is made
with the adjusting nuts on page 18.
2. Screw out the fork (3) to relieve... Dismantle the front hood and right-hand fender
as described on the back edge of Rider 970 1. Lower the cutting unit at the front edge by pulling out the rear pin (1). Adjustment of the
lift-strut...
Owners Manual - Page 27
... away from the height adjustment.
Dismantle the cutting unit on Rider 970 Bioclip as described on page 18.
2
2. Set the cutting height to the ground. Remove the hair-needle...Push the stop (1) in the reverse order to the lowest position. MAINTENANCE
Dismantling the cutting unit
The cutting unit can be pulled forward until it is now locked vertically.
3. Fitting of the...
Owners Manual - Page 32
... purposes.
English Always use the mixing ratios indicated by an authorised service...sparks or pilot flames in order for extra protection. Carefully clean the machine, especially under the cutting...stabiliser has been added.
! Remove the plug and pour in the tank or the... inflammable and negligent usage can harden. Start the engine and run it will reach...970
RIDER 850
RIDER 850
30 -
Owners Manual - Page 33
... Manufacture
Power Displacement Fuel
Tank volume Oil
Oil volume Start
Electrical system Type Battery Spark plug
Transmission Manufacture Oil
Cutting unit Type Cutting width (Bioclip) Cutting height Blade diameter (Bioclip)
NOISE LEVEL
Rider 850
...unit with side/rear ejection/Bioclip 965 mm (970-15.5/15.5S), 1030 mm
9 pos. 40-90 mm, 45-80 mm (Bioclip) 350 mm (970-15.5/15.5S), 410 mm
100 dB(A)
We...
Similar Questions
Saw Cuts Out When Sawing Vertically On A Wall.
I'm a mechanic for the US Corps of Engineers. A crew is doing concrete work on lock and damn 15 in I...
I'm a mechanic for the US Corps of Engineers. A crew is doing concrete work on lock and damn 15 in I...
(Posted by sfcwcs 2 years ago)
Spark Plug / Husqvarna K760 Concrete Saw
what is the correct/ best plug gap for my k760 concrete/cut saw?
what is the correct/ best plug gap for my k760 concrete/cut saw?
(Posted by mikeylehman 5 years ago)
Spark Plug Gap
what is the proper spark plug gap for the Husqvarna k970 concrete saw?
what is the proper spark plug gap for the Husqvarna k970 concrete saw?
(Posted by toddmwied 6 years ago)
970 Saw Cuts For One Minute
ssaw start then cuts out in minutes start again dies with minutes again
ssaw start then cuts out in minutes start again dies with minutes again
(Posted by mblkmtn 8 years ago)
Have The K760 Concrete Saw. Wont Start,
have the k760 concreate saw , wontstart ive found oil in the de compreshion switch bore, and spark p...
have the k760 concreate saw , wontstart ive found oil in the de compreshion switch bore, and spark p...
(Posted by nevjones2010 9 years ago)