Hunter 90064 Support Question
Hunter 90064 Support Question
Find answers below for this question about Hunter 90064.Need a Hunter 90064 manual? We have 1 online manual for this item!
Question posted by j4molo on September 4th, 2013
With One Switch Installation The Night Light Does Not Work.
The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hunter 90064 Manual Pages
Owner's Manual - Page 1
Owner's Manual
Model
90063/90064
1
41722-01 09/09/2011 Ellipse
Bath Ventilator with Light and Night Light
English
Español
Página 21
41722-01 20110909 ©2011 Hunter Fan Co.
Owner's Manual - Page 2
...a ceiling thermally insulated to tab) and twist screwdriver. protected branch circuit.
8. Never place a switch where it must be vented to the service panel.
3. This unit must be marked as ...If you have questions, contact the manufacturer. Installation work and electrical wiring must always be grounded.
11. Unit must point upward.
4. Gently vacuum fan, motor and interior of the housing or ...
Owner's Manual - Page 3
Before Installation
1
30
20
O FF
O FF
Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes
NOTE: Remove all ...-01-000 E 95022-01-000 F 75190-01-000 G 03242-07-133 H 95492-02-000 x2 I
Extra Screws
* NOTE: Strain relief cable connector must be installed. x5 A
*B *C
3/8" Cable Connector
x2 I 74508-03-133 J 77520-01 K 65219 L 95740-01/02-000 M 75184-01-133 N 95366-01/02...
Owner's Manual - Page 5
... bottom edge of the joist based on the thickness of your sheetrock. Screw pre-loaded screws into the housing and secure with the washer. Choose Installation Option
For New Construction -
Owner's Manual - Page 6
... cover plate screw. A13
Pull wires through the strain relief.
A15
F A16
2
1
F
G•
Install the wiring cover plate.
A14
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
Owner's Manual - Page 9
... strain relief. B18
Tighten screws.
B17
Attach the rails onto the screws.
B19
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
9
41722-01 09/09/2011
B15...
Owner's Manual - Page 10
... by inserting the tabs and pushing up into position. If ducting does not fit securely, an adapter may need
to the wiring cover plate. B20
F
2
1
F
Install the wiring cover plate. B23
H
Connect 4" duct and vent to the outside.
Owner's Manual - Page 11
... the motor housing as a template to attach grille. B28 Go to step E1
on the power source. accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to make sure the opening is large enough to accommodate the new
motor housing (9"x 9.75").
B26
Turn on page 18...
Owner's Manual - Page 14
... Red Night Light
Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
C26
H H
Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into
position. C23
2
1
F
Install the...
Owner's Manual - Page 15
...
E1
OFF
on the power source. If the motor does not run, check the plug connection. Test the motor. accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to attach grille.
Owner's Manual - Page 16
D15
D14
2 1
Attach existing ducting to be purchased. D16
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
16
41722-01 09/09/2011 Tape joints. E
Screw pre-loaded...
Owner's Manual - Page 17
... the wiring cover plate screw. D21
H
Reinstall the motor by tightening the 2 screws.
17
41722-01 09/09/2011
Turn on the power source.
D17
2
1
F
Install the wiring cover plate. D22
I
Secure the motor by inserting the tabs and pushing up into position. D20
H
Connect wiring from the motor to the...
Owner's Manual - Page 19
... with a new bulb. • T urn power on .
E7
L
Install 2 Max 60 Watt A-15 bulbs (Not Included) and 1 Max 7 Watt C-7 bulb (Not Included). To
confirm that the fan is noisy. E5
E6
M
Slide light mount over posts and attach thumbscrews. Problem: Light does not come on , replace fuse, or reset breaker. • Check all 4
thumbscrews...
Owner's Manual - Page 20
... OF GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.
Warranty
Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY
Hunter Fan Company makes the following ... installation, modifications or damage to the Hunter bath exhaust fan while in your Hunter bath exhaust fan is not purchased and installed in China
20
41722-01 09/09/2011
©2011 Hunter Fan ...
Similar Questions
How Does The Night Light Work
installed unit but the night light isn;t working
installed unit but the night light isn;t working
(Posted by gillenterry 4 years ago)
90063/90064 Bath Ventilator With Light And Night Light
Can I order only the replacement glass/frame attachment 95366-01/02-000 for my existing unit I now h...
Can I order only the replacement glass/frame attachment 95366-01/02-000 for my existing unit I now h...
(Posted by Wesley6 5 years ago)
Replacement Glass For Hunter 90064
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
(Posted by Jwaller0717 7 years ago)
The Switch For The Light Is Not Working.
The switch for the light is not working. Should I replace the switch housing?
The switch for the light is not working. Should I replace the switch housing?
(Posted by Anonymous-158923 7 years ago)
How Do You Wire The Night Light Function?
How do you wire the night light function?
How do you wire the night light function?
(Posted by kww46 10 years ago)