Hunter 90058 Support Question
Hunter 90058 Support Question
Find answers below for this question about Hunter 90058.Need a Hunter 90058 manual? We have 2 online manuals for this item!
Question posted by c66 on October 20th, 2013
Exhaust Fan Not Working
We have the Hunter 90058 exhaust fan and light and the fan is no longer working. Where is the fuse box located and where can you buy the fuse to try that
Current Answers
Related Hunter 90058 Manual Pages
Owner's Manual - Page 1
Installation Guide
ENGLISH
See page 2
Español
Vea la página 21
90052/90053/90054/90058 Saturn™ Bath Ventilator with Light
READ and SAVE THESE INSTRUCTIONS
028_41718_EngS_1.28.08_Arial.indd 1
1
41718-01 01/28/2008
1/28/08 10:47:06 AM
Owner's Manual - Page 2
...switched on the motor plate (located next to a value greater ...work and electrical wiring must be vented to tab) and twist screwdriver. Unit must always be marked as listed below. To avoid motor bearing damage and noisy/unbalanced impellers, keep drywall spray, construction dust, etc. Disconnect the power supply and clean the fan as appropriate for proper combustion and exhausting...
Owner's Manual - Page 6
Make sure all wiring connections are inside the box or under
the wiring cover plate. Tape joints.
A15
A016
E
G
Install the ... AM
If ducting does not fit securely, an adapter may need
to the outside. A14
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch ...
Owner's Manual - Page 9
... all wiring connections are inside the box or under the wiring cover plate.
Connect 4" duct and vent to be purchased.
9
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 9
1/28/08 10:47:24 AM B19
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper...
Owner's Manual - Page 11
... the bottom edge of the joist based on the thickness of screws by using holes as a template to mark position. accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to make sure the opening for the housing.
Mark position of your sheetrock.
Existing Construction -
Owner's Manual - Page 13
...box or under the wiring cover plate.
13
41718-01 01/28/2008
Connect wiring from the motor to the wiring cover plate.
028_41718_EngS_1.28.08_Arial.indd 13
1/28/08 10:47:35 AM
C23
C24
F
H
G
Install the wiring cover plate.
C21
Tighten the strain relief screws. C22
Fan Motor Light...
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together...
Owner's Manual - Page 15
...:40 AM D14
2 1
Pull wires through strain relief. E
Screw pre-loaded screws into position above the ceiling.
accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to duct connector.
Tape joints. D15
Attach existing ducting to accommodate the new...
Owner's Manual - Page 16
D19
H
Connect wiring from the motor to the wiring cover plate. D16
Fan Motor Light
2 Pin
Black White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch 2 (AC In)
Connect wires as ....28.08_Arial.indd 16
1/28/08 10:47:43 AM
Make sure the wires are inside the box or under the wiring cover plate.
Owner's Manual - Page 18
...posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). E3
E4
J K
Remove the strain relief bracket screw. E6
L
Insert the strain relief bracket's dog-...leg tab so that it hooks over posts. Slide light fixture over the lip of electrical shock, all 4 thumbscrews MUST be properly installed.
18
Install...
Owner's Manual - Page 19
... your hand near the vents to make sure it moves freely. To confirm that the fan is secure. • C heck the flapper to make sure it matches the wiring diagram.
Problem: Light does not come on , replace fuse, or reset breaker. • Check all plug connections to be sure they are extremely quiet...
Owner's Manual - Page 20
... makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan:
If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within five years after the date of sale to you due to a defect in material or workmanship, we will...
Similar Questions
Need Replacement Fan For Hunter Bathroom Exhaust Fan 83001/83701
Need replacement fan for Hunter bathroom exhaust fan 83001/83701
Need replacement fan for Hunter bathroom exhaust fan 83001/83701
(Posted by smstraka 3 months ago)
Exhaust Fan Will Not Work
I absolutely LOVE this exhaust fan, light, night light combo. However, the exhaust fan will not work...
I absolutely LOVE this exhaust fan, light, night light combo. However, the exhaust fan will not work...
(Posted by pennydgreene 6 years ago)
Pull Switch On Light No Longer Works. Where Do I Get A Part Or How Can I Fix It?
(Posted by mtaylorfieds 9 years ago)
Lights No Longer Turn On But Fan Still Works On Hunter 28684 Bought In 2012.
My lights were on for about 10 minutes then I heard a 'zap' sound and all the lights went out. I bou...
My lights were on for about 10 minutes then I heard a 'zap' sound and all the lights went out. I bou...
(Posted by donlncln 9 years ago)