Hunter 42999 Support Question
Find answers below for this question about Hunter 42999.Need a Hunter 42999 manual? We have 3 online manuals for this item!
Question posted by tjchristianson on March 23rd, 2014
Installed New Batteries
just installed new batteries. system will not work. all lights in box are lit simultaneously
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Hunter 42999 Manual Pages
Owner's Manual - Page 3
... have selected one of our broad line of service. Table Of Contents
Installation
Features
6
Remove Old Thermostat
8
Labeling Wires
10
Connecting Wires and Mounting Thermostat
14
System Selector Switches
14
Operation
Start-Up
16
Reviewing Current Temperature Setting
16
Setting New Temperature
17
Filter Monitor
18
Resetting Filter Counter To Zero
19
Temperature Span...
Owner's Manual - Page 4
... there are power outages. Read This Before Installing Thermostat
IMPORTANT
1Read the entire installation section of your favorite chair and is normally performed at your air conditioner compressor caused by inserting and connecting the batteries and following the instructions on page 14. This Hunter Thermostat will prevent damage to your thermostat. This can practice programming before...
Owner's Manual - Page 5
...°F (5°C and 35°C). When this happens, install new batteries immediately.
CAUTION: The batteries are low the "LOW BATT" indicator on the display will continue to not operate properly. Rechargeable batteries have different properties which may cause the thermostat to operate for
approximately 30 days. (Only alkaline batteries should last one year. TEMPERATURE RANGE
6Your...
Owner's Manual - Page 6
... turning on heating and cooling system. s Reset Button For resetting thermostat. s For lowering temperature.
Features (Model 42999)
6-7
69 TEMP
SET TEMP
C
FILTER
LO BAT
HOLD
HEAT COOL
s Easy-To-Read Digital Display Liquid crystal display shows room temperature, set temperature, filter indicator, low battery indicator, heat and cool system indicator.
s Fan ON and...
Owner's Manual - Page 8
... to removal. s Slotted screwdriver s Hammer
s Electric drill and 3/16" bit s Two 1.5V (AA) Size Alkaline batteries
Remove Old Thermostat
CAUTION: Do not remove any wiring from existing thermostat before reading the instructions carefully. Installation
8-9
What You Need
This thermostat comes with two #8 slotted screws and two wall anchors for wires. Wires must first be connected...
Owner's Manual - Page 10
... a terminal point on that no terminal marking on the existing thermostat of two wire, heat only systems. Do not worry, just connect either of the wires to the RH terminal, then connect the other wire to the W terminal to complete the circuit.
Installation
10-11
Label Wires
s Each wire coming from the wall...
Owner's Manual - Page 11
... mark wire with label shown
RH RC
G
Y
W or H Heating
W TABLE A
and connect to your existing thermostat is
RH, R, VR or 4 24 Volt
RC, VC 24 Volt Cool
NOTE: Follow the labels when connecting wires since many installations do not follow color coding of wires.
Wire Labeling
This table will help you match...
Owner's Manual - Page 12
... RH and RC terminals. NOTE: Do not connect a "Common" wire (sometimes labelled "C") to any terminal on this thermostat.
Tape up the wire and do not use. Installation
12-13
Wire Labeling (Continued)
NOTE: If your thermostat has one wire marked R or RH (4-wire system), then leave the jumper wire between the RH and...
Owner's Manual - Page 15
... into the wallplate. (NOTE: Do not force the thermostat onto the wallplate, as the terminal pins may not work.)
s Insert the two AA size batteries, observing the polarity marked on the main power. s The installation is in AUTO. Press top of the thermostat body to prevent interference with your house. Press the reset button. (See...
Owner's Manual - Page 16
...;C) for heat and 78°F (25°C) for more than 2
68 TEMP
SET TEMP
F
FILTER
seconds, you first install two AA size batteries, as directed in timer prevents damage to 37°C). s The thermostat will prevent memory loss and avoid reprogramming. Reviewing Current Temperature Setting
s 69° is current room temperature.
69 TEMP...
Owner's Manual - Page 3
... are pleased you for years of home comfort products. Table Of Contents
Installation
Features
6
Remove Old Thermostat
8
Labeling Wires
10
Connecting Wires and Mounting Thermostat
14
System Selector Switches
14
Operation
Start-Up
16
Reviewing Current Temperature Setting
16
Setting New Temperature
17
Filter Monitor
18
Resetting Filter Counter To Zero
19
Temperature Span...
Owner's Manual - Page 4
... provide a delay when there are power outages. Read This Before Installing Thermostat
IMPORTANT
1Read the entire installation section of this Owner's Manual thoroughly before installing your air conditioner compressor caused by inserting and connecting the batteries and following the instructions on page 14.
This Hunter Thermostat will prevent damage to operate with all the functions of...
Owner's Manual - Page 5
.... BATTERY WARNING
8When the batteries are the only source of power used in your heating and cooling system will continue to operate for approximately 30 days. (Only alkaline batteries should last one year.
TEMPERATURE RANGE
6Your thermostat can be away from 32°F to 99°F (0°C to 37°C). When this happens, install new batteries immediately...
Owner's Manual - Page 6
... resetting thermostat.
s Function Switch For turning on heating and cooling system.
s For raising temperature.
s For lowering temperature.
s Fan ON and AUTO Selector Switch. Features (Model 42999)
6-7
69 TEMP
SET TEMP
C
FILTER
LO BAT
HOLD
HEAT COOL
s Easy-To-Read Digital Display Liquid crystal display shows room temperature, set temperature, filter indicator, low battery...
Owner's Manual - Page 8
... and 3/16" bit s Two 1.5V (AA) Size Alkaline batteries
Remove Old Thermostat
CAUTION: Do not remove any wiring from existing thermostat before reading the instructions carefully. s IMPORTANT! Once wall mounting plate... to the back of the wallplate. Some thermostats will have the following tools and materials. Again, look for mounting. To install your unit, you should have screws or other...
Owner's Manual - Page 10
... a terminal point on that no terminal marking on the existing thermostat of two wire, heat only systems. Do not worry, just connect either of these do not have to be as few...any number in between. Installation
10-11
Label Wires
s Each wire coming from the wall to the existing thermostat is usually marked with the standard. This air could cause a false thermostat reading.
Each of the...
Owner's Manual - Page 15
... it does not snap properly, the thermostat may be damaged.
s The installation is set at the bottom of the wallplate. s Push excess wire back into the wallplate. (NOTE: Do not force the thermostat onto the wallplate, as the terminal pins may not work.)
s Insert the two AA size batteries, observing the polarity marked on the...
Owner's Manual - Page 16
... - Reviewing Current Temperature Setting
s 69° is displayed.
s The thermostat is preset at the factory to 68°F (20°C) for heat and 78°F (25°C) for more than 2
68 TEMP
SET TEMP
F
FILTER
seconds, you first install two AA size batteries, as directed in timer prevents damage to 37°C).
HOLD...
Owner's Manual - Page 1
...01 Rev 6-29-2001 JUST RIGHT ® DIGITAL THERMOSTAT
Owners Manual Model 42999B
Congratulations...installing and operating your thermostat, you should provide well over 30 days, we recommend that thermostat. Please read this message occurs, install new alkaline batteries...thermostat is designed to work .)
• Insert the two AA size alkaline batteries, observing the polarity marked inside the battery...
Owner's Manual - Page 2
... to
the system.
4. Hold the key down the thermostat. Filter Monitor
The thermostat counts the number of the thermostat.
This setting INCREASES the cycle time by battery symbol flashing on the LCD display, and shuts off until new batteries are installed in the "HG" position.
Auto Cut Off
Your thermostat will be reset to see whether the Heat...
Similar Questions
New Batteries, Yet Still Get Battery Low Message
Got the "battery low" message. Changed the batteries, it didn't go away. The thermostat now speaks t...
Got the "battery low" message. Changed the batteries, it didn't go away. The thermostat now speaks t...
(Posted by kubby 1 year ago)
How Do You Set These Thermostat It's Just Run And Run And Run And Run The House
(Posted by betteroil777 4 years ago)
How To Change My Thermostat From Celsius To Fahrenheit
(Posted by cmarieeha15 9 years ago)
When A Hunter Thermostat 44132 Is Installed The Heat Works In A/c Mode
(Posted by fpescbillw 10 years ago)