Hunter 28680 Support Question

Find answers below for this question about Hunter 28680.
Need a Hunter 28680 manual? We have 4 online manuals for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by Daneg007 on September 1st, 2023

Replacement Part Needed

What kind of capacitor is needed for replacement

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on September 1st, 2023 11:34 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,620,300

1,100
points

The Hunter 28680 capacitor is a 5 microfarad, 370 volt capacitor that is used in some Hunter ceiling fans. It is a start capacitor, which means that it helps the fan to start up. The capacitor is located in the fan's motor housing.

Here are the technical specifications of the Hunter 28680 capacitor:

Microfarads: 5

Volts: 370

Type: Start

If you are replacing the capacitor in your Hunter ceiling fan, it is important to make sure that you get the correct one. The capacitor should have the same microfarad and voltage rating as the original capacitor. You can also check the capacitor's capacitance and voltage rating on the capacitor itself.

You can buy a Hunter 28680 capacitor from a variety of online and offline retailers. Some popular retailers include:

amazon

other local

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Answer #2: Posted by INIMITABLE on September 1st, 2023 10:13 AM

INIMITABLE

Member since:
April 3rd, 2020

Points: 2,081,730

100
points

The Capacitor for this Wire harness is Red=300VAC, Brown 250VAC and Purple 250VAC. Thank you for your inquiry, good luck with this repair!

I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers

-INIMITABLE

Related Hunter 28680 Manual Pages

Installation Guide - Page 1

... Ceiling Height 7' Minimum to Floor 30" From Wall or Nearest Obstruction Step 1 Choose the Fan Site Proper ceiling fan location and attachment to the building structure are aligned with joist or support brace. Tools and Supplies You May Need • Drill • Keyhole saw • 2' x 4' support brace • UL-approved octagonal 4" x 1-1/2" outlet box...

Owner's Manual - Page 1

Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42439-01 20100615 ©2010 Hunter Fan Co. Model Name Model No. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual.

Owner's Manual - Page 2

..., or motor damage, do not bend the blade attachment system when installing, balancing, or cleaning the fan. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to supply you are proud of the...

Owner's Manual - Page 3

...connector. • Six inches of the fan and light kit. If your new Hunter fan. Preparing the Fan Site Step 1 - Choose the Fan Site Proper ceiling fan location and attachment to the building structure... box is directly below the joist or support brace. If you want to use an existing fan site, complete the following checklist to outlet box by wood screws and washers through the inner...

Owner's Manual - Page 4

.... 4-3. If you to the service panel. 5-2. read the fan supply line through the inner holes of the ceiling. Preparing the Fan Site (continued) Step 2 - If the joist is there, determine ... screws (5/64") through the outlet box so that will hold the outlet box and fan. 2-2. Attach the fan supply line to the support brace or joist with an approved connector, available at least...

Owner's Manual - Page 5

...higher than 8 feet high CAUTION: To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to assure stability and wobble-free .... For quiet and optimum performance of three ways, depending on ceiling height and your Hunter fan, use only Hunter speed controls. Angled Mounting Style 8 12 Angled Mounting recommended for a...

Owner's Manual - Page 6

... are essential for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. Installing Multiple Fans? Proper ceiling fan location and attachment to the motor or fan blades. If you need the following : • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for safety, reliable...

Owner's Manual - Page 7

...Plate 3" Wood Screw Steps 2-3 - 2-6 7 42439-01 • 06/15/10 • Hunter Fan Company The pilot holes should be 9/64" in the center of the two 3" wood screws. 2-4.... 2-3. 2 • Installing the Ceiling Plate CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as a tag,...

Owner's Manual - Page 8

... the ball. 3-3. For Low Profile mounting: Note: For low profile mounting, the downrod is replaced with the lip down. 3-6. Securely retighten the setscrew with the holes in the canopy with three low profile screws. Raise the fan and align the slots in the adapter. Align the holes in these installation instructions. 3-1. Place...

Owner's Manual - Page 9

...) from the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan. 4-4. Select an acceptable general-use switch in accordance with national and local electrical codes and ANSI/...bare or green ground wire (grounding) from the ceiling to the white wire (grounded) from the fan. 4-5. Connect the white wire (grounded) from the ceiling to the green ground wire (grounding)...

Owner's Manual - Page 10

... top of the hanger ball. 5-6. When all the holes are still in the hanger ball. Note: Your fan may have multiple tabs and grooves that the tabs in the canopy are properly aligned, securely tighten all three... the ceiling plate. Rotate the hanger ball so the tab in the canopy is recommended you need to remove the trim ring, press firmly on opposite sides of the trim ring directly above the ...

Owner's Manual - Page 11

Note: The blades on this fan have been treated with a protective cloth to prevent scratching the blades. 2. Using pliers,...they are completely separated from the blade iron. 3. Carefully remove the blade. 11 42439-01 • 06/15/10 • Hunter Fan Company Step 6-1 Step 6-2 CAUTION: Be sure blade is completely visible. Blade Removal: 1. 6 • Assembling the Blades Our exclusive...

Owner's Manual - Page 12

... 7-3 - 7-5 Lower Switch Housing 12 42439-01 • 06/15/10 • Hunter Fan Company 7 • Completing Your Installation With a Bowl Light Fixture Upper Switch Housing Plug Connector ...Housing Assembly Screw WARNING: Use only the light fixture supplied with this ceiling fan contains a device that restricts its light output. Install the third housing assembly screw. 7-5....

Owner's Manual - Page 13

...Continued) Installing the Glass Bowl 7-6. Place the cover plate up against the glass bowl. Thread the fan pull chain through the hole in the side of the extra chain.) For Light Bulbs Metal Disc Metal... the plastic breakaway connector on the end of the cover plate. 7-9. Thread the light and fan pull chains through the grommet hole in the center of the cover plate. 7-8. Thread the light...

Owner's Manual - Page 14

... soft brush or lint-free cloth to the opposite position. Slide the reversing switch on the fan to prevent scratching. The light pull chain controls the power to a complete stop. A vacuum...or any residue, as they will damage the 8-6. 8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on this happens, simply reinsert the chain into the blades. • The chain uses...

Owner's Manual - Page 15

... made for dimming. Wait 5 minutes, then resume power to balance the fan. 2. If you need parts or service assistance, please call 1-866-268-1936) or visit us at our Web site at the wall switch. Remove the shipping bumpers. If so, replace all the blades. Turn the power to make sure the wattage...

Parts Guide - Page 1

... Globe/Shade Light bulb / Bulb Balancing Kit Model # 28679 Asm. Dwg. # G0829-01 28680 G0829-02 28681 G0829-03 Finish Qnty 1 Onyx Bengal Brushed Nickel White Part # 96759-90 Part...x 4 Connector Screw, Switch x 3 Housing Assembly Hanger Bracket Assembly Blade Assembly Switch Housing Assembly Fan Parts (Not Drawn to Scale) 150 PARTS GUIDE Using this Parts Guide, make sure all parts...