Hunter 25748 Support Question

Find answers below for this question about Hunter 25748.
Need a Hunter 25748 manual? We have 4 online manuals for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by anita2k2k on August 14th, 2015

Hunter Fan 25748 Not Working Correctly

I have a wall switch & a remote control for my Hunter ceiling fan. When the wall switch is on, the lights go on. Then I would press the remote for the fan but it WON'T turn. I can turn off the lights with the remote control and I can also hear the fan gently "click" when I reverse the blade direction but the fan won't turn. Then hours later, the fan would turn by itself when left untouched. What's my problem?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on September 10th, 2015 1:37 PM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,843

1,090
points

Turn power on, replace fuse, or reset breaker.
Loosen canopy, check all connections according to the wiring the fan section.
Check the plug connection in the switch housing.
Push motor reversing switch firmly left or right to ensure that the switch is engaged.
Pull the pull chain to ensure it is on.6. Remove the shipping bumpers

Clean the unit

For cleaning finishes, use a soft brush or lint-free cloth to prevent scratching. A vacuum cleaner brush nozzle can remove heavier dust. Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth. You may use an artistic agent, but never abrasive cleaning agents as they will damage the finish. Clean wood finish blades with a furniture polishing cloth. Occasionally, apply a light coat of furniture polish for added protection and beauty. Clean painted and high-gloss blades in the same manner as the fan finish

If you need parts or service assistance, please call

888-830-1326

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Hunter 25748 Manual Pages

Installation Guide - Page 1

... to your new Hunter fan. Fan Support System Fan Support System Suitable Existing Fan Site Wiring Outlet Box Hunter Fan Company Step 2 Cut the Ceiling Hole 2-1. If NOT, install a support brace as specified by wood screws and washers through the inner holes of the ceiling. Make sure the circuit breakers to the fan supply line leads and associated wall switch location are...

Owner's Manual - Page 1

For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42419-01 20081124 ©2008 Hunter Fan Co. Model Name Model No.

Owner's Manual - Page 2

... _ and Receiver 10 8 • Completing Your Installation 11 9 • Operating the Remote Control _ and Mounting the Holder 14 10 • Operating and Cleaning Your _ Ceiling Fan 15 11 • Troubleshooting 16 Welcome Your new Hunter® ceiling fan is an addition to the service panel. • All wiring must be in accordance with national and local electrical...

Owner's Manual - Page 3

...'s patented 3-position mounting system provides you can install your Hunter fan in this manual include instructions for ceilings less than 8 feet, you maximum installation flexibility and ease. Considering Optional Accessories Consider using Hunter's optional accessories, including a wall-mounted or remote speed control. For quiet and optimum performance of your preference: Low Profile...

Owner's Manual - Page 4

..., as they were shipped. 4 42419-01 • 11/24/08 • Hunter Fan Company If you need the following : • Locate the ceiling joist or other suitable support in the pullout sheet called "Preparing the Fan Site." 1 • Getting Ready To install a ceiling fan, be sure you can direct you to a licensed installer or electrician. Check...

Owner's Manual - Page 5

... into the pilot holes you drilled in diameter. Step 2-2 Flat Washer Toward Ceiling Peak Steps 2-3 - 2-5 3" Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. 5 42419-01 • 11/24/08 • Hunter Fan Company Drill two pilot holes into the holes in the...

Owner's Manual - Page 6

... profile mounting, the downrod is pointing up toward the ceiling. Steps 3-1 - 3-2 Setscrew Steps 3-3 - 3-4 Ceiling Plate Tabs Step 3-5 Downrod Canopy Low Profile Washer #8-32 x 1" Screw Canopy Slots 6 42419-01 • 11/24/08 • Hunter Fan Company 3 • Assembling and Hanging the Fan You can assemble your fan for standard mounting (steps 3-1 - 3-2) or for low profile mounting...

Owner's Manual - Page 7

... • 11/24/08 • Hunter Fan Company To connect the wires, hold the bare metal leads together and place a wire connector over them carefully back through the ceiling plate into the outlet box. 4-7. If you are unfamiliar with national and local electrical codes and ANSI/NFPA 70. Wall switches are visible after making connections. 4-6.

Owner's Manual - Page 8

... the Canopy 5-1. Partially install a canopy screw into the hole between the two ceiling plate tabs. Step 5-4 Step 5-5 8 42419-01 • 11/24/08 • Hunter Fan Company Rotate the hanger ball so the tab in the canopy is secure in the... Should you need to the top of the canopy. Press firmly on the ceiling plate. 5-3. WARNING: Failure to complete this step could cause...

Owner's Manual - Page 9

... attach lightly to a blade iron using three blade assembly screws. Insert the second blade mounting screw, then securely tighten both mounting screws. This is normal. 6-3. Step 6-1 (Detail) Grommet Use with grommet Blade Assembly Screws Steps 6-1 - 6-2 Use without grommet Blade Mounting Screw Step 6-4 9 42419-01 • 11/24/08 • Hunter Fan Company Your fan...

Owner's Manual - Page 10

...or modifications not expressly approved by Hunter Fan Company could void your authority to a different code, so that incorporates an air gap switch (normal on (encendido) CAUTION: The remote control device complies with this equipment. ... 1 4 = off (apagado) 3 = on (encendido) 24 ==ooffff((aappaaggaaddoo)) 31 == oonn ((eenncceennddiiddoo)) 2 = off (apagado) 1 = on -off wall switch).

Owner's Manual - Page 11

... situated in the housing with step 8-6 now. Install the remaining screw into the switch housing mounting plate. 8-2. See "Uninstalling the Light Fixture" on step 8-11. 8 • Completing Your Installation With or Without a Multi Staked Light Fixture Your Hunter fan comes with this fan model. 8-1. Turn the housing counterclockwise until the housing assembly screws are installing...

Owner's Manual - Page 12

...Steps 8-8 - 8-10 12 42419-01 • 11/24/08 • Hunter Fan Company Note: Both plug connectors are properly aligned before Plug Connector connecting them. Align the side screw holes in the lower switch housing assembly. 8 • Completing Your Installation With or Without a Multi Staked Light Fixture (Cont.) Steps 8-6 - 8-7 Lower Switch Housing Plug Connector Detail 8-6.

Owner's Manual - Page 13

...08 • Hunter Fan Company Kit 8-15. Remove the receiver from the light kit. Install the dummy terminals (included in the upper and lower switch housings. Place the lower switch housing assembly over the upper switch housing. Place the receiver into the alternate switch housing. Connectors 8-14. Attach the lower switch housing to the upper switch housing with the...

Owner's Manual - Page 14

... your desired brightness. Press the OFF button to any toggle switch plate with a 12-volt type 23A, MN-21 battery or equivalent. 9-6. Push the light button again to full brightness. You can simply mount the remote holder on to turn the fan off and on and controlling the light and fan speed. 9-2. The light button turns the light on the wall. Or, you...

Owner's Manual - Page 15

..., but never abrasive cleaning agents as the fan finish. 10 • Operating and Cleaning Your Ceiling Fan 10-1.Turn on the fan to the opposite position. A vacuum cleaner brush nozzle can remove heavier dust. Slide the reversing switch on electrical power to the fan. 10-2.The fan pull chain controls power to the fan. The pull chain has four settings...

Owner's Manual - Page 16

... plug connection in the switch housing. 4. Problem: Lights dim when turned on or do not turn on , replace fuse, or reset breaker. 2. Check to balance the fan. 2. 11 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Tighten the blade assembly screws and blade iron armature screws until snug. 2. Problem: Excessive wobbling. 1. Hunter Fan Company 2500 Frisco Avenue...

Parts Guide - Page 1

...Switch Housing, Alternate Switch Housing Cover Switch Housing Plug Button Balancing Kit Remote Control Transmitter Remote Control Cradle Remote Control Receiver Globe/Shade 12 Volt Battery (GP23A) Light bulb / Bulb Model # Asm. Dwg. # Finish Qnty 1 25746 93752-03 White 74090-02 25745 93752-06 Antique Pewter 25748... 77646-03 77646-03 77646-03 Hunter Fan Company • 7130 Goodlett Farms...