Hoover UH70400 Support Question
Hoover UH70400 Support Question
Find answers below for this question about Hoover UH70400.Need a Hoover UH70400 manual? We have 1 online manual for this item!
Question posted by codabear1968 on July 10th, 2011
Belt Motor Blew Out
i think my belt motor on my hoover windtunnel burn out because brush will not turn no more and there is oil around it now
Current Answers
Related Hoover UH70400 Manual Pages
Manual - Page 1
... reserved. #961101001-01 ID 100148-R0 For assistance, please call Customer Service at 1-800-944-9200 Mon-Fri 8am-7pm EST. página E1
www.hoover.com
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE. Questions or concerns? IF USED COMMERCIALLY WARRANTY IS VOID.
©2010 Techtronic Floor Care Technology Limited. Owner...
Manual - Page 2
... Use...6 Vacuum Description 6 On-Off Switch 6 Carry Handle 6 Cord Storage 6 Telescopic D-Grip Handle 7 Handle Positions 7 Tools ...7 Select Proper Tool 7 Removing Hose 7 Attach Wand And Tools 8 Stair Cleaning 8 Maintenance...9 Dirt Cup...9 Filters...10 Brushroll...11 Belt...12 Troubleshooting 13 Service...14 Warranty...15
If you need assistance: Visit our website at Hoover.com or...
Manual - Page 3
...FIRE, ELECTRIC SHOCK OR INJURY:
• Fully assemble before operating. • Operate vacuum only at bottom of stairs on cord. Not intended for use by pulling on floor.... Unplug from openings and moving parts. • Turn off all controls before cleaning or servicing. • Do not use with damaged cord or plug.
If appliance is burning or smoking, such as a handle, close a ...
Manual - Page 4
... may continue. Do not change the plug in the outlet, reverse the plug. Turn cleaner OFF and unplug it from the electrical outlet. 2. This blockage may cause ...designed into your cleaner needs servicing.
4 If this appliance has a polarized plug (one blade is unplugged and motor cools for 30 minutes, the thermal protector will fit in a polarized outlet only one way. When cleaner is...
Manual - Page 5
....
1.3 To remove handle, press lever (A) again and pull handle out of vacuum base.
1.2
A
Attach dirt cup
1.4 Place bottom of dirt cup into tool ... button to secure into place.
1.4
1.3
A
Position Tools
1.5 For storage mode, push dusting brush all the way up onto crevice tool.
1.6 Snap combination tool into vacuum body first. Press down on select models only.
1.1
A
B C
D
Remove all parts ...
Manual - Page 6
... intended for convenient storage.
2.4
Attach the plug end to the cord.
2.5 Twist upper cord hook (D) to allow cord to Handle 14. Brushroll Window 19. To turn vacuum ON, push ON/OFF switch (A) once. CARRY HANDLE
2.3
C
The cleaner can be released.
2.5
D
6 ON/OFF Brushroll Switch 6. Filter made with HEPA media 10. Hose Release...
Manual - Page 7
The vacuum is ready for carved furniture, table tops, books, lamps, lighting fixtures, venetian blinds, baseboards, shutters, and registers. Crevice Tool may be used for tool use , press the hose release button and pull hose end out. B.
Dusting Brush may be used in tight spaces, corners and along edges in upright position.
Use...
Manual - Page 8
... extension wand or hose.
Press handle wand release button and pull handle up to the stair hose*.
Press the hose release button on stairs. Unplug vacuum before connecting wand or tools. For extended cleaning reach, you may result in the upright position.
WARNING ! Do not place cleaner on floor.
Manual - Page 9
... removing the dirt cup.
4.1
!
Press firmly to secure into place.
4.3
B
4.2
A
4.4
A
9 Press down on the dirt cup release button to secure.
4.4 Place bottom of your vacuum will ensure continued cleaning effectiveness. Any other servicing should be done by an authorized service representative. Dirt Cup: When to open dirt cup door (B). Do ...
Manual - Page 10
... servicing. Return filter and replace dirt cup on both sides of injury from moving parts, unplug vacuum before replacing. Ask for Hoover® Part No. 303903001.
If desired, additional filter is available. Ask for Hoover® Part No. 303902001.
4.8
A
4.9
10 This may take up to dry completely before servicing. To reduce the risk...
Manual - Page 11
... filter assembly (A) up . For additional maintenance required for belt or brushroll please contact a HOOVER® service provider at 1-800-944-9200.
4.15 Vacuum is facing up out of the dirt cup.
4.12 ... hose end out. To reduce the risk of injury from moving parts, unplug vacuum before servicing.
4.14 Turn vacuum over so bottom side is equipped with the dusting/ upholstery tool.
4.13 Place...
Manual - Page 12
...as shown with your vacuum. When purchasing a new belt, ask for Belt -
How To Replace
Place handle in belt guide on side of belt into place. HOOVER® part No...belt. Turn the agitator making sure the belt is not pinched between agitator and agitator shield.
4.20 Place the bottom plate aligning the screw holes and install the 6 screws as shown place belt in the low position and turn...
Manual - Page 13
... Hose not installed correctly. 3. Review filter removal and cleaning - Belt broken or stretched.
1. Check fuse or breaker in firmly. Empty dirt cup - Dirt cup not installed correctly. 2. with HEPA media - pg 6
2. Clear/ remove debris from vacuum
Brushroll will not turn Smoky/burning smell detected
POSSIBLE CAUSE
POSSIBLE SOLUTION
1.
Empty dirt cup - Rinsable...
Manual - Page 14
..., AB T5W 2P2, Phone: 1-800-944-9200, Mon-Fri 8am-7pm EST. Always identify your vacuum to Hoover®, Inc., Company in delay. Service
To obtain approved Hoover® service and genuine Hoover® parts, locate the nearest Authorized Hoover® Warranty Service Dealer (Depot) by the complete model number when requesting information or ordering...
Manual - Page 15
... the product by any such defect in products purchased in normal household use outside of Hoover® products. This Warranty shall be paid one way. However, if you .... OTHER IMPORTANT TERMS This Warranty is not as maid, janitorial and equipment rental services), brushroll, belt, improper maintenance of the product, damage due to products purchased outside the United States, including...
Similar Questions
Seal On The Uh70400 Red Suction Tube
I don't know the proper name for this part but all the dirt is sucking up into the red tube & fi...
I don't know the proper name for this part but all the dirt is sucking up into the red tube & fi...
(Posted by mlallenx3 2 years ago)
Motor That Controls Brush Doesn't Work...belt Is Not Broken! Any Ideas?
I lightly bumped the leg of a table and the motor just stopped working...no smoke, no smell, no funn...
I lightly bumped the leg of a table and the motor just stopped working...no smoke, no smell, no funn...
(Posted by nccorgi 9 years ago)
Motor
when i start to vacuum the motor is spinning then it stops i'm afraid it will burn. what should i do...
when i start to vacuum the motor is spinning then it stops i'm afraid it will burn. what should i do...
(Posted by bobbienjack 11 years ago)
On A Uh70400 There Is A Bracket That Supports The Rear Wheels. What Is It Called
What is the name of the bracket that supports the rear wheels on a UH70400? It is pictured on the pa...
What is the name of the bracket that supports the rear wheels on a UH70400? It is pictured on the pa...
(Posted by kevinflahertycontracting 11 years ago)
My Motor Shaft Is Not Turning. I Replaced The Flat Belt.
I replaced the flat belt and it made horrible noise. When I opened the bottom again, the new flat be...
I replaced the flat belt and it made horrible noise. When I opened the bottom again, the new flat be...
(Posted by msw01 12 years ago)