Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by hendzele on May 31st, 2011
Wiring Problems
Why do I need to always reverse my blue and red wires when I change from heat to cool mode?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...thermostat has been designed for fast and easy installation. Call 1-800-468-1502.
1 Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires.... Mount the new wallplate. Connect the wires. If the wire labels don...
Owner's Manual - Page 3
..., oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2
RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type or if you...
Owner's Manual - Page 4
Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Contact your old thermostat in the trash if it contains mercury in a sealed tube.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and ...
Owner's Manual - Page 5
... to your new thermostat. Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled.
Wrap the bare metal end of these wires with electrical tape, so it cannot touch and short other wires. RTH2310 Programmable Thermostat
Identify...
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors.
Owner's Manual - Page 7
...any excess wire back into the wall opening. Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5. Labels...
Owner's Manual - Page 8
If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below.
Wrap bare end of wire with electrical tape. Quick Installation Guide
Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7 Do not use C, X or B.
Owner's Manual - Page 9
HE Place the jumper to the G terminal. RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Set the Jumper J2, on the back of the thermostat, if you have a gas or oil furnace.
J2 jumper
HG Leave the jumper in this position if you have connected a wire to this factory-set position if you have an electric furnace.
8
Owner's Manual - Page 10
...will display the ambient temperature once it is installed on the wall. The thermostat will hear a clicking
sound. It is 70 °F (21 &#... be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. After the batteries are holding the thermostat. Observe the
polarity. 3) Reinstall the battery cover. Quick Installation ...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2,...heating control, use the setting that matches your system as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 min, 6=10 min
09-08
11
Printed in bold and underlined.
2 See page 3 of Operating Manual.
3 Use the system switch to the next function, briefly press both and buttons simultaneously.
3) To change...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
How To Wire A Heat Pump To It
How to wire a heat pump to th5110d1022
How to wire a heat pump to th5110d1022
(Posted by corykelly2 10 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)
Ct51n Wiring Connection For Cooling
I have a Honeywell CT51N thermostat and only the wiring for heating is listed in the manual. How do ...
I have a Honeywell CT51N thermostat and only the wiring for heating is listed in the manual. How do ...
(Posted by milkchok12 12 years ago)