Home » Honeywell » Thermostats » Honeywell CT8775A

Honeywell CT8775A Support Question

Find answers below for this question about Honeywell CT8775A.
Need a Honeywell CT8775A manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by lgdenault on January 2nd, 2012

Where Can I Buy The Digital Thermostat Ct8775a

The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Honeywell CT8775A Manual Pages

Owner's Manual - Page 1

... Heating and/or Cooling System 13 If You Have A Problem ...15 Wiring Diagrams...16 ® U.S. Label Thermostat Wires ...5 Step 5. CT8775A,C THE DIGITAL ROUND™ NON-PROGRAMMABLE THERMOSTATS CT8775A Heat Only Thermostat (20 to 30 Vac) and CT8775C Heating-Cooling Thermostat (20 to 30 Vac) Para obtener un documento con las instrucciones en español, por favor...

Owner's Manual - Page 2

... cause a hazardous condition. The temperature setting is held permanently in memory in home comfort controls. the state of the art in the event of The Digital RoundTM Thermostat by Honeywell. • Simple to -read the display in the trash. COOLER WARMER ROOM SET M19582 MERCURY SWITCH TYPICAL LOCATION OF A MERCURY SWITCH IN...

Owner's Manual - Page 3

...volt)b Single Stage Heat Pump Multistage Heat Pumps/Multistage Equipment Compatibility with CT8775A Yes No Yesa Yes Yes No No No No No Compatibility with ... 3 • Screws and wall anchors • Hammer 69-1676-1 Compatibility Chart. Package Contents • Thermostat • Wiring labels Tools for Installation • Screwdriver • Needle nose pliers • Decorator cover...

Owner's Manual - Page 4

... or screws that has one of these systems. For information about which thermostats will work properly. Replacing a thermostat that has wires connected to Step 4. Wrap the wires separately using electrical...with the installation at 1-800-468-1502. 69-1676-1 4 If you are replacing a thermostat that may have either system does not work, contact your system, call Honeywell Customer Care,...

Owner's Manual - Page 5

...; To mount directly to the place of purchase. The CT8775A thermostat is installed. Replacing a thermostat that is connected to three wires on a zoned hot water heating system If you are replacing a thermostat that is connected to three wires on a zoned hot water heating system, the CT8775A,C thermostats will work if an isolation relay is not compatible...

Owner's Manual - Page 8

... conditioning contractor. FOR WRAPAROUND INSERTION STRIP 7/16 IN. (11 MM). G ❑ Refer to the labels you placed on the wires when you removed the Y old thermostat (see illustration). ❑ Match the letter of these terminals. ❑ For wiring diagrams, see illustration). Tighten the terminals. ❑ Plug the hole in the wall...

Owner's Manual - Page 9

...to Rc. 2. Tape off B with electrical tape and do not use . 9 69-1676-1 W - - - - Terminal on Old Thermostat R Rh (see Note 1) 4 V Rc R (see Note 1) W, W1, H Y, Y1, M G, F O B (see...Terminals Connect To Terminals on CT8775A on the new thermostat and connect Rh to R and R to a single stage heat pump. Table 2. Terminal Designations on the old thermostat, remove jumper between R ...

Owner's Manual - Page 10

...10065; To adjust the fuel switch, locate the switch labeled E/F on the back of the thermostat. See Table 3. Fuel switch. BACK OF THERMOSTAT ON 123 69-1676-1 DIP SWITCH M19567 Fig. 4. FUEL SWITCH M19497 Fig. 3. Set ...1, 2 and 3 on the wallplate (see Fig. 3). NOTE: The CT8775A,C Thermostats will provide optimal temperature control if DIP switches 1 and 2 are set in the F position.

Owner's Manual - Page 11

... TABS AT BOTTOM OF THERMOSTAT AND WALL PLATE. Heating System Cycles Per Hour DIP Switch 1 DIP Switch 2 Steam, Gravity 1 High Efficiency Warm Air (90%+ efficiency), Hot Water, Heat Pump 3 On ...

Owner's Manual - Page 12

CT8775 Thermostat (features and operation). 12 SET THE SYSTEM AND FAN SWITCHES (CT8775C ONLY) System Switch (see Fig. 5) ❑ Fan Auto: Normal .... ❑ Fan On: The fan runs continuously. Use for most homes. STEP 10. Fan Switch (see Fig. 5) ❑ Heat: The thermostat controls your heating system. ❑ Off: Both the heating and cooling systems are off. ❑ Cool: The...

Owner's Manual - Page 13

... display to raise the temperature setting. A indicator points to the temperature setting is displayed. Adjust Temperature Setting ❑ Turn the dial clockwise to indicate the thermostat has called for heating. CHECK OPERATION OF HEATING AND/OR COOLING SYSTEM Heating System ❑ Slide the system switch to Heat and the Fan switch...

Owner's Manual - Page 14

...not operate cooling when outside temperature is made before restarting. Allow compressor to indicate the thermostat has called for cooling. The cooling system should turn off for cooling is below the...-1 14 The snowflake will flash during this delay. ❑ After five minutes, the thermostat will go into a five-minute delay to Auto. The fan should run continuously. ❑...

Owner's Manual - Page 15

...8226; Make sure the temperature setting is below model number). • Type of thermostat). • Thermostat date code. (Located below the room temperature. • Make sure the circuit... 5. Solution Guide. Before calling, please have the following information available: • Thermostat model number. (Located on the wallplate. • Make sure the circuit breaker is...

Owner's Manual - Page 17

...COIL FAN RELAY 1 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. 2 REMOVE FACTORY INSTALLED JUMPER BETWEEN R AND RC. M19454 Notice: This thermostat is a Class B digital apparatus that complies with Canadian Radio Interference Regulations, CRC c. 1374. 17 69-1676-1 PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. 2 FACTORY INSTALLED JUMPER...