Hitachi NT65GS Support Question
Hitachi NT65GS Support Question
Find answers below for this question about Hitachi NT65GS - 2-1-2" 16 Gauge Gas Powered Straight Finish Nailer.Need a Hitachi NT65GS manual? We have 2 online manuals for this item!
Question posted by mickmanus27 on January 17th, 2021
Firing Plate Problem
firing plate does not return to position. Tried flat head screwdriver to push back to no avail.
Current Answers
Answer #1: Posted by hzplj9 on January 17th, 2021 2:01 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,874,710
Member since:
June 25th, 2012 Points: 4,874,710
The firing plate could be jammed with a staple or nail depending on what is being used. If it (whatever it is) is stuck above the plate it will stop it returning. It could be that the plate is bent for the same reason. You will need to dis-assemble the unit to find out what is calling the jam I'm afraid. I would suggest if you are attempting it yourself take photos as you go so re-assembly will be simpler.
Hope that helps.
Related Hitachi NT65GS Manual Pages
Instruction Manual - Page 6
... NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. Never carry the Nailer with the Nailer. This Nailer exhausts carbon ...gas.
Do not spray to operate below
32°F (0°C) or above 104°F (40°C).
6 Always assume the Nailer contains fasteners. ALWAYS WEAR EAR AND HEAD PROTECTION. This Nailer shall not be used in
explosion or fire.
EXPLOSION AND FIRE...
Instruction Manual - Page 7
... becomes especially heavy in use the Nailer unless the push lever is operating properly, otherwise the Nailer could drive a fastener unexpectedly. KEEP FACE, HANDS AND FEET AWAY FROM FIRING HEAD DURING USE. Never place your face, hands or feet closer than 8 inches (200 mm) from the point of unnecessary tools, debris, furniture, etc.
12. KEEP VISITORS...
Instruction Manual - Page 9
...to local regulations for aerosol products. Store in fire and explosion when handling dispensers for combustible gas for recycling.
Contact a doctor if necessary.
...Fire Hazard
Failure to follow all instructions may result in well-ventilated area.
120°F MAX Do not store above 120°F (50°C) (e.g. the person affected should be taken into a comfortable position...
Instruction Manual - Page 10
... than than 25 (7.5) 50 (15) 100 (30) 150 (45)
0
2 18 18 18 16
2
3 18 18 16 14
3
4 18 18 16 14
* If the input rating of plug on (1) battery charger, (2) battery, and (3) product ...operated tools as those of a battery charger is given in watts rather than in a risk of electric shock, unplug charger from improper or unsafe use of battery charger as specified in a risk of fire, electric...
Instruction Manual - Page 11
...out. NEVER 2. NEVER 4. insert any other than with a DC 12V in a fire. charge when the temperature is low humidity and good ventilation. ALWAYS operate charger on ... instructions and cautionary statements on minusgrounded vehicles. short-circuit the battery. ALWAYS disconnect the power cord from driving. If you use . NEVER 7. incinerate the battery, even if ... use the Nailer.
Instruction Manual - Page 12
...EMPLOYER'S RESPONSIBILITIES
1. Keep Nailers in your area for recycling options or proper disposal. SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
12 Continued
4. Enforce ... not leave the vehicle unattended during charging as this may result in a fire or accident due to direct sunlight during charging.
English
SAFETY - Check with your local...
Instruction Manual - Page 13
Gas Finish Nailer
Top cover
Actuator
Chamber
Handle
Top cover
Chamber
Actuator Handle Battery
Piston
Driver blade
Trigger
Battery Hook
Piston
Driver blade
Trigger
Firing head
(outlet)
Magazine
Push lever Nail feeder (B)
Top cover
Chamber
Actuator Handle
Magazine
Firing head (outlet)
Nail feeder (B)
Push lever
⅜ Battery (EMB315)
Terminal hole
Piston
Trigger
...
Instruction Manual - Page 14
Gas Brad Nailer
Top cover
Chamber
Piston Driver blade
Actuator Handle
Battery
Trigger
Hook Stop lever
Firing head
(outlet)
Push lever
Magazine
Magazine cover
3. Battery Charger (UC3SML)
Strap
Battery installation hole
Connecting socket
Charger connecting plug
Pilot lamp
Nameplate (on the bottom side)
Charger connecting ...
Instruction Manual - Page 16
... can result in tool malfunction and/or nail breakdown, leading to use of nails
16 Gauge finish nails (straight)
Min. .110" (2.8mm)
Max.
2-1/2" (65mm)
1" (25mm) .051" (1.3mm)
.055" (1.4mm)
.065" (1.65mm)
16 Gauge finish nails (Angle: 20°)
Min. .110" (2.8mm)
Max.
2-1/2" (65mm)
1-1/4" (32mm) .051" (1.3mm)
.055" (1.4mm)
.065" (1.65mm)
16
English
NAIL SELECTION
WARNING...
Instruction Manual - Page 26
...guide grooves and Groove properly, then push the magazine cover forward to avoid accidental firing.
ⅷ Use outside or well-ventilated area.
ⅷ Do not inhale its contents.
WARNING
ⅷ NEVER point tool at yourself or others in work...work area.
ⅷ Keep fingers AWAY from
ignition source.
ⅷ No smoking.
NAILER OPERATION
Read section titled "SAFETY"(pages 5 - 12).
Instruction Manual - Page 27
... to be driven. First, press the push lever against the workpiece; To ensure that gets on the workpiece with a FULL SEQUENTIAL ACTUATION MECHANISM. It is intermittent operation (Trigger fire) only. 1 Position the nail outlet on the tool. English
ⅷ Do not use Nailer which is not loaded with Nailer at too steep of unwanted fastener. If...
Instruction Manual - Page 28
... Flush
(2) Remove the hook and hook plate.
2 Too Shallow
Turn Adjuster Flush
If nails...turning the adjuster when a suitable position is reached for adjuster. To ...screwdriver.
2 If nails are driven too shallow, turn the adjuster to the Nailer. It is always held firmly against the workpiece. Fuel cell
USING THE HOOK
CAUTION ⅷ If the tool falls, there is a risk that the Nailer...
Instruction Manual - Page 29
...nailer. English
Nose Cap
Magazine
NT65GS, NT65GA, NT65GB
USING THE NOSE CAP
WARNING
ⅷ When attaching or detaching the nose cap, be sure to its thickness. CLEARING A JAM
If nails are jammed in firing head... scratches or markings made by the push lever, attach the accessory nose cap to the push lever. 1 Remove the fuel cell and the battery from the Nailer.
2 Remove all nails.
29
Re...
Instruction Manual - Page 30
Lock lever
3 Guide Plate 4 Remove the jammed nail with a slottedhead screwdriver.
5 Close guide plate and latch. NOTE: ⅷ In case of frequent jam, contact a Hitachi
authorized service center.
30 English 3 Release the lock lever and open guide
plate.
Instruction Manual - Page 33
...PROBLEM Nailer...head screwdriver, and put back the piston to the highest position.
Keep push lever working Promote operator safety and Blow clean daily. Check function of piston smoothly. Check push lever's moving of nail feeder per page 31. Use only recommended nails. Blow clean daily.
CHECK METHOD Check for replacement.
33 Contact Hitachi for replacement.
efficient Nailer...
Instruction Manual - Page 105
...
74 TRIGGER SPRING
75 CORD COVER PLATE
76 CHAMBER SPRING
77 HEX. NT65GS
ITEM NO. SOCKET HD. BOLT M4×12
3
33 LOCK PLATE
1
34 LOCK LEVER COVER
1
35... BOLT M4×12
4
7A CYLINDER HEAD
1
8 NUT M3
2
9 SPRING WASHER M3
2
10 WASHER M3
2
11 FAN
1
12 RUBBER PLATE
1
13 HEX. BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
...
Instruction Manual - Page 107
... (W/FLANGE) M5×10
4 TOP COVER
5 SPARK PLUG (A)
6 NYLOCK BOLT M4×12
7 CYLINDER HEAD
8 NUT M3
9 SPRING WASHER M3
10 WASHER M3
11 FAN
12 RUBBER PLATE
13 HEX. BOLT M4×16
14 CHAMBER HEAD
15 GASKET
16 CHAMBER
17 PISTON RING (B)
18 RETAINING RING FOR D40 HOLE
19 PACKING
20 ADAPTER
21...
Instruction Manual - Page 109
...TERMINAL SUPPORT
70 TRIGGER SPRING
71 TRIGGER
72 CORD COVER PLATE
73 CHAMBER SPRING
74
SEAL LOCK HEX. BAR WRENCH 4MM
505 NOSE CAP (A)
506 CASE
Q'TY
1 2 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 2
2
1 1 1 1 1 1 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1
109 BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
18 RETAINING RING FOR D40 HOLE...
Instruction Manual - Page 111
...(A)
1
6 NYLOCK HEX. BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
18...;10 2
79 PUSH LEVER ARM
1
80 PUSH LEVER PIECE
1
81 O-RING (S-8)
1
82 ADJUSTER
1
83 RATCHET SPRING
2
84 PUSHING LEVER (A)
1
... M4×12 4
7 CYLINDER HEAD
1
8 NUT M3 (10 PCS.)
2
9 SPRING WASHER M3
2
10 WASHER M3
2
11 FAN
1
12 RUBBER PLATE
1
13 HEX. SOCKET HD....
Parts List - Page 2
...43 886-287 BUFFER COVER
1
44 886-288 MUFFLER
1
45 886-290 REED VALVE
1
46 886-293 BUFFER PLATE
1
47 886-294 O-RING
1
48 886-292 MESH
1
49 305-812 TAPPING SCREW (W/FLANGE) D4X16 (...-
*ALTERNATIVE PARTS
NT 65GS 6 - 08 BOLT M4X16 (10 PCS.)
4
14 886-295 CHAMBER HEAD
1
15 886-296 GASKET
1
16 886-297 CHAMBER
1
17 886-312 PISTON RING (B)
4
18 886-298 RETAINING RING FOR D40 HOLE...
Similar Questions
Screeching Noise
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
(Posted by Rongowrie 2 years ago)
Won't Fire
how my hitachi NT 65GB will not fire it makes the noise as if it will fire but nothing happens when ...
how my hitachi NT 65GB will not fire it makes the noise as if it will fire but nothing happens when ...
(Posted by farrelljames989 5 years ago)
Nail Gun Won’t Work
my nail gun stopped working after using it twice,I opened back up and a fan is loose,is this the pro...
my nail gun stopped working after using it twice,I opened back up and a fan is loose,is this the pro...
(Posted by Iandharkness 5 years ago)
New Hitachi Nt65gs
first time using the nailer with 16ga nails, it starts firing two at a time. i dont want to use it u...
first time using the nailer with 16ga nails, it starts firing two at a time. i dont want to use it u...
(Posted by log07012746 10 years ago)
Gun Doesn't Always Fire On The First Trigger Poll.
Gun usually will fire on the 2nd or 3rd, but not always on the first.
Gun usually will fire on the 2nd or 3rd, but not always on the first.
(Posted by hstancil 13 years ago)