Hitachi DS14DVF Support Question
Hitachi DS14DVF Support Question
Find answers below for this question about Hitachi DS14DVF - 14.4 Volt 3/8" Driver/Drill.Need a Hitachi DS14DVF manual? We have 2 online manuals for this item!
Question posted by swimmer1946 on December 11th, 2021
I Was Given The Above Cordless Driver Drill But Without Any Drill Bits. I Know I
I know it takes a Phillips bit (No. 2x55L)(code No. 318236). Is there other drill bits that I should buy for it?
Current Answers
Answer #1: Posted by SonuKumar on December 12th, 2021 8:01 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,633,680
Member since:
May 9th, 2021 Points: 16,633,680
https://www.amazon.com/s?k=drill+bits&crid=JP9NXB8TBQIP&sprefix=drill+b%2Caps%2C451&ref=nb_sb_ss_ts-doa-p_3_7
there are plenty of option available .
make slecet as per the need like wall bit, iron bit or wood bit
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hitachi DS14DVF Manual Pages
Instruction Manual - Page 3
...Read and understand all of this Instruction Manual. NEVER use this power tool in a manner that result from power tool operation and maintenance are caused by the failure to prevent bodily injury... information.
3 Most accidents that has not been specifically recommended by WARNINGS on the power tool and in this Instruction Manual and in the sections which , if ignored, could result in ...
Instruction Manual - Page 4
... pack. Loose clothes, jewelry, or long hair can cause you are doing and use tool while tired or under the influence of fire.
3. Always wear eye protection. Be sure...a risk of fumes. (3) Keep bystanders children, and visitors away while operating a power tool. FOR ALL BATTERY OPERATED TOOLS
WARNING: Read and understand all times. Do not wear loose clothing or jewelry. Personal ...
Instruction Manual - Page 5
... create a risk of children and other practical way to secure and support the workpiece to another tool.
5. Use the correct tool for one terminal to a stable platform. WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other small metal objects that cannot be suitable for your model. Holding the work in...
Instruction Manual - Page 6
....
9. Keep all guards in place. Check their condition periodically.
12. Because the cordless driver drill operates by children, individuals unfamiliar with a "live" wire will make exposed metal parts of the fact that it can cause hearing loss.
3. Use right tool. don't use tool for purpose not intended -for applications other people and be aware of...
Instruction Manual - Page 7
...with solvent. Definitions for repairs by a Hitachi authorized service center. 15. V volts direct current
no load speed
---/min ... NEVER use a tool which is defective or operating abnormally. Do not wipe them with such solvents. ..., it immediately and arrange for symbols used on this tool. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI
Standard Z87...
Instruction Manual - Page 8
...plug when disconnecting
battery charger. 7. That extension cord is given in good electrical condition;
An extension cord should not be...
0
2
2
3
3
4
18
18
18
18
18
18
18
16
16
14
16
14
* If the input rating of fire, electric shock, or injury to damage or ...volts = 10 amperes
9. This manual contains important safety and operating instructions for UC14SD...
Instruction Manual - Page 9
... NEVER 11. ALWAYS
13. ALWAYS 14. short-circuit the battery. insert ...cordless driver drill. Do not operate battery charger if it to read all instructions and cautionary statements on standard household electrical power (120 volts...injury. The battery can use only where there is completely worn out. take it has received a sharp blow, been dropped, or otherwise damaged in...
Instruction Manual - Page 10
The battery is incinerated. SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
10 At the end of it's useful life, under various state and local laws, it
is recyclable. Check with your local solid waste officials for ...
Instruction Manual - Page 11
...Cordless Driver Drill Keyless Chuck
Cap L Indication Switch Trigger
Handle
Shift Knob Housing Bit
Push Button
Nameplate
R Indication
Keyless Chuck
Cap L Indication Switch Trigger
Handle
Battery
Shift Knob Housing
Bit
Push Button
Nameplate
R Indication
Battery
11
NEVER operate, or attempt any maintenance on your own power tool...the tool unless you in this manual. MODEL
DS9DVF: ...
Instruction Manual - Page 13
Cordless Driver Drill
Model Motor No-load speed
Low High
DS9DVF
0-280/min 0-840/min
DS12DVF DC motor 0-350/min 0-1050/min
DS14DVF
0-400/min 0-1200/min
Capacity Drilling
Wood...6mm)
1/4"(6mm)
Drill chuck capacity
Maximum gripping diameter 3/8" (10mm)
Battery Model
EB912S/EB914 EB1212S/EB1214L EB1412S/EB1414
Type
Nickel cadmium battery
Voltage
DC 9.6V
DC 12V
DC 14.4V
Charging & ...
Instruction Manual - Page 14
...
APPLICATIONS
⅜ Use as a drill Drilling of soft steel, wood, plastic and aluminum materials.
⅜ Use as a screwdriver Tightening and loosening of the tool, causing injury to you or someone... around you. (Fig. 3)
⅜ How to install the battery.
If charged at voltage higher than indicated on the nameplate, the charger will burn up.
14...
Instruction Manual - Page 17
... the sleeve by turning it further. When the trigger is depressed, the tool rotates. Grasp the bit installed in the keyless chuck, in the clockwise direction as viewed from the rear side) by
Triger switch
pushing the R-side of the drill can be applied for immediate stopping.
17 Confirm that the trigger switch...
Instruction Manual - Page 18
...8mm) diameter × 1-1/4"(32mm).
Strong
(2) When using this unit as a screwdriver, line up the cap drill mark
" " with the shift knob, confirm that the switch is set. Change rotation speed
High speed
... knob to "LOW". If "HIGH" is set the shift knob to change the rotational speed. DS12DVF / DS14DVF
When the diameter of
the numbers "1, 3, 5 ... 22" on the cap, or the black dot,
...
Instruction Manual - Page 19
...the black dot.
ⅷ Do not use with the triangle mark on the outer body. While
operating the driver drill, take care not to lock the motor. ⅷ When setting the shift knob to "HIGH" (high speed) ... locked. English
mark
CAUTION:
ⅷ The cap cannot be set between the
number "22" and the drill mark " ". In such a case, please set the shift knob to the screw diameter. Doing so may...
Instruction Manual - Page 20
... 70 in-lbs. (80 kg-cm)(DS14DVF)
Low speed: approximately 156 in-lbs....drilling purpose.
1 - 22 1 - Use the bit and socket matching the screw diameter.
q Do not tighten too strongly as a drill. NOTE: The selected content shown in -lbs. (60kg-cm)
Screw tightening for a while, the motor or battery will be burnt.
CAUTION: q While operating the Cordless driver drill, take...
Instruction Manual - Page 21
...of wear from normal use a driver bit of Hitachi Power Tools must be changed without prior notice.
21 In the operation and maintenance of power tools, the safety regulations and standards ...CAUTION: If you use . MODIFICATIONS: Hitachi Power Tools are dangerous.
code numbers and/or design) may damage the plastics.
4. The bits should be observed. English
MAINTENANCE AND INSPECTION
CAUTION:...
Instruction Manual - Page 22
...318236) ....... 1 2 Battery (EB1212S or EB1214L 2
3 Battery Charger (UC12SD 1
4 Plastic Case (Code No. 319967 1
1
2
3
4
DS14DVF
22
1 Phillips bit (No. 2 × 55L)(Code No. 318236) ....... 1 2 Battery (EB1412S or EB1414 2 3 Battery Charger (UC14SD 1
4 Plastic Case (Code No. 320653 1 English
ACCESSORIES
WARNING: ALWAYS use a particular replacement part or accessory with this tool...
Parts List - Page 1
F869
ELECTRIC TOOL PARTS LIST
CORDLESS DRIVER DRILL Model DS 14DVF
2003 • 2 • 24 (E2)
1 3
2
8
2
4
9
10 11
12
18
13
19
14
20
21
22
23 24
25
5 6 7
15 16 17
26
501
30
501
31
32
38
502
37 36 35
34
503
33
27 28 29
504
39
505
42 41
40 LIST NO.
Parts List - Page 2
CODE NO.
1 318-228
DESCRIPTION SPECIAL SCREW (LEFT HAND) M5X27
NO.
USED
1
REMARKS
2 312-516 DRILL CHUCK 10TLRD-N (W/O CHUCK WRENCH)... RING GEAR
1
13 312-705 PLANET GEAR (C) SET (3 PCS.)
3
14 312-704 WASHER (A)
1
15 312-697 REAR CASE
1
16 315-817...-672 TAPPING SCREW (W/WASHER) D3X16
8
* 28
NAME PLATE
1
29 318-237 BIT HOLDER
1
30 949-203 MACHINE SCREW M3X8 (10 PCS.)
2
31 949-451...
Parts List - Page 3
... 14SD)
* 501
CHARGER (MODEL UC 14YF2)
502 318-236 + DRIVER BIT NO.2 55L
* 503 320-653 CASE (OFF-BLACK GREEN)
* 503 321-982 CASE (BLACK)
* 504
BIT SET
* 505
TORCHLIGHT (MODEL UB 18D)
NO. USED
REMARKS
1
1
1
1
1
1 EXCEPT FOR NZL
1 EXCEPT FOR NZL, GBR
DS 14DVF
2 -- 03
* ALTERNATIVE PARTS
--- 3 --- CODE NO.
STANDARD ACCESSORIES
ITEM NO.
Similar Questions
I Need To Plan Interior Parts
I want to order parts to repair my Hitachi drill 14.4 v half drive ... 2.4Ah ... you can call me t...
I want to order parts to repair my Hitachi drill 14.4 v half drive ... 2.4Ah ... you can call me t...
(Posted by commtel 9 years ago)
How Do I Secure A Drill Bit To My Hitachi Wh14daf2?
I am trying to secure my drill bit to my Hitachi WH14DAF2, but the only bits that sit securely are t...
I am trying to secure my drill bit to my Hitachi WH14DAF2, but the only bits that sit securely are t...
(Posted by fire1321 11 years ago)
How To Read Battery Symbols On Charger
I have a Hitachi 14.4 volt cordless drill, DS 14DV, but had to get after market batteries which fit ...
I have a Hitachi 14.4 volt cordless drill, DS 14DV, but had to get after market batteries which fit ...
(Posted by sandy63901 12 years ago)
Ds14dvf Keyless Chuck Removal
I need to replace the keyless chuck on my DS14DVF drill. I removed the screw from te bottom of the c...
I need to replace the keyless chuck on my DS14DVF drill. I removed the screw from te bottom of the c...
(Posted by mdallison 13 years ago)