Hitachi DS14DVF Support Question
Hitachi DS14DVF Support Question
Find answers below for this question about Hitachi DS14DVF - 14.4 Volt 3/8" Driver/Drill.Need a Hitachi DS14DVF manual? We have 2 online manuals for this item!
Question posted by sandy63901 on January 2nd, 2012
How To Read Battery Symbols On Charger
I have a Hitachi 14.4 volt cordless drill, DS 14DV, but had to get after market batteries which fit both ways into the charger. The charger has 4 symbols which nobody can accurately 'translate' for me. Can you? Here they are: solid red line with empty battery picture, dashed red line with full battery sign, dotted red line with 'X' through the picture and solid green line with a symbol I don't recognize. Thank you!
Current Answers
Related Hitachi DS14DVF Manual Pages
Instruction Manual - Page 3
... precautions, warnings and operating instructions in the Instruction Manual before it occurs, and by HITACHI. Hazards that result from power tool operation and maintenance are identified by the failure to prevent bodily injury or machine damage... instructions. NOTE emphasizes essential information.
3 English
IMPORTANT SAFETY INFORMATION
Read and understand all of this power tool.
Instruction Manual - Page 4
... of fire when used for the battery. Loose clothes, jewelry, or long hair can cause you are doing and use tool while tired or under the influence of the tool may result in serious personal injury. (2) Dress properly. FOR ALL BATTERY OPERATED TOOLS
WARNING: Read and understand all times. A charger that is off position before turning the...
Instruction Manual - Page 5
... a HITACHI authorized service center. WARNING:
Some dust created by hand or against your exposure to these chemicals: work in the hands of untrained users. (6) When battery pack is unstable and may create a risk of parts, and any adjustments, changing accessories, or storing the tools. Holding the work by power sanding, sawing, grinding, drilling, and...
Instruction Manual - Page 6
...tool's housing or handle can cause hearing loss.
3. Do not use a power tool for cutting tree limbs or logs.
9. Such tools should be used until repaired.
13. English
SPECIFIC SAFETY RULES AND SYMBOLS
1. Hold tools...Hold the drill by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Because the cordless driver drill operates by...
Instruction Manual - Page 7
.... 16. Definitions for repairs by a Hitachi authorized service center. 15. Should a power tool be operating unusually, making strange noises, or...volts direct current
no load speed
---/min ... Carefully handle power tools. revolutions per minute
7 If the tool appears to be dropped or struck against hard materials inadvertently, it immediately and arrange for symbols used on this tool...
Instruction Manual - Page 8
... as those of injury, charge HITACHI rechargeable battery type EB912S and EB914 for UC9SD, EB1212S and EB1214L for UC12SD and EB1412S and EB1414 for battery charger Model UC9SD, UC12SD and UC14SD.
2. Before using battery charger, read all instructions and cautionary markings on battery charger: b. Make sure cord is large enough for example:
1250watts 125 volts = 10 amperes
9. That blades...
Instruction Manual - Page 9
... the model UC9SD, UC12SD or UC14SD battery charger, be sure to avoid overheating the charger.
NEVER 7. ALWAYS
13. Keep the battery away from direct sunlight and use the cordless driver drill. Do not operate battery charger if it , the battery and in this risk. Do not disassemble battery charger; OTHER TYPES OF BATTERIES MAY BURST AND CAUSE INJURY! ALWAYS...
Instruction Manual - Page 10
... your area for recycling options or proper disposal. SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
10 The battery is incinerated.
English
DISPOSAL OF THE EXHAUSTED BATTERY WARNING: Do not dispose of this battery into the municipal waste stream. The product that you have purchased contains a rechargeable...
Instruction Manual - Page 11
... of the power tool. MODEL
DS9DVF: with charger (UC9SD) and case DS12DVF: with charger (UC12SD) and case DS14DVF: with charger (UC14SD) and case
NAME OF PARTS
1.
Cordless Driver Drill Keyless Chuck
Cap L Indication Switch Trigger
Handle
Shift Knob Housing Bit
Push Button
Nameplate
R Indication
Keyless Chuck
Cap L Indication Switch Trigger
Handle
Battery
Shift Knob Housing
Bit...
Instruction Manual - Page 12
English
⅜ Battery Terminal Hole
Terminal Hole
Terminal Hole
Nameplate
Nameplate
Latch
Nameplate
Latch
Fig. 1
Latch
2. Battery Charger (UC9SD, UC12SD and UC14SD)
Air vent
Battery Installation Hole
Cord
Pilot Lamp
Plug
Name Plate
Caution Plate
Fig. 2
12
Instruction Manual - Page 13
Battery Charger Model Input power source Charging time Charging voltage Charging current Weight
UC9SD
UC12SD
UC14SD
Single phase: AC120V 60Hz
Approx. 60min. (At a temperature of 68°F (20°C)
DC 9.6V
DC 12V
DC 14.4V
DC 1.55A
DC 1.55A
DC 1.55A
2.6 lbs. (1.2kg) 3.3 lbs. (1.5kg) 3.5 lbs. (1.6kg)
13 Cordless Driver Drill
Model Motor No-load speed...
Instruction Manual - Page 14
...
Handle
Insert Pull out
Latch Push
Battery
Insert Pull out
Fig. 3
Latch Push Battery
CHARGING METHOD
NOTE: Before plugging into place. Withdraw battery from the tool handle while pressing the latch (1 pc. If charged at voltage higher than indicated on the nameplate, the charger will burn up.
14
Align the battery with the groove in place with...
Instruction Manual - Page 15
... shown in Fig. 4. When the pilot lamp does not go out. Disconnect battery charger from the receptacle and check
if the battery is low or the voltage of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER.
4. Insert the battery into the receptacle, charging will
commence and the pilot lamp will go...
Instruction Manual - Page 16
...the next charging.
Remove the battery from the battery charger. Regarding electric discharge in case of unnecessary personnel. If you feel that have not been used , the battery charger will be heated, thus ...and its life will be low when using the tool and recharge its internal chemical substance will deteriorate, and the battery life will be shortened. English
CAUTION: Do not ...
Instruction Manual - Page 17
...the sleeve by turning it toward the right (in a vise or similar tool. NOTE: Loosening stuck or hard to the left (in the counterclockwise direction... front). (See Fig.5)
CAUTION: When mounting a bit into the keyless drill chuck. Set the cap position to turn on the body.) ⅜...viewed from the rear side) by
varying the amount that the battery is not tight, the bit may slip or fall out, ...
Instruction Manual - Page 19
...22" on the cap, or the black dot, with the triangle mark on the outer body. While
operating the driver drill, take care not to lock the motor. ⅷ When setting the shift knob to cease while the unit is...
CAUTION:
ⅷ The cap cannot be set between the
number "22" and the drill mark " ". When too strong power is about to excessive tightening. ⅷ A buzzing noise is produced when ...
Instruction Manual - Page 20
...Cordless driver drill, take care not to screw type, screw size and material used as the screw heads will be damaged.
20 If the motor is locked, immediately turn the power off.
NOTE: The selected content shown in -lbs. (60kg-cm)
Screw tightening for a while, the motor or battery...kg-cm)(DS12DVF)
approximately 70 in-lbs. (80 kg-cm)(DS14DVF)
Low speed: approximately 156 in-lbs. (180 kg-cm...
Instruction Manual - Page 22
... Phillips bit (No. 2 × 55L)(Code No. 318236) ....... 1 2 Battery (EB1212S or EB1214L 2
3 Battery Charger (UC12SD 1
4 Plastic Case (Code No. 319967 1
1
2
3
4
DS14DVF
22
1 Phillips bit (No. 2 × 55L)(Code No. 318236) ....... 1 2 Battery (EB1412S or EB1414 2 3 Battery Charger (UC14SD 1
4 Plastic Case (Code No. 320653 1
Contact HITACHI if you are not sure whether it is safe...
Parts List - Page 1
LIST NO. F869
ELECTRIC TOOL PARTS LIST
CORDLESS DRIVER DRILL Model DS 14DVF
2003 • 2 • 24 (E2)
1 3
2
8
2
4
9
10 11
12
18
13
19
14
20
21
22
23 24
25
5 6 7
15 16 17
26
501
30
501
31
32
38
502
37 36 35
34
503
33
27 28 29
504
39
505
42 41
40
Parts List - Page 2
... BALL D5
6
12 312-715 RING GEAR
1
13 312-705 PLANET GEAR (C) SET (3 PCS.)
3
14 312-704 WASHER (A)
1
15 312-697 REAR CASE
1
16 315-817 SCREW SET D3X12 (6 PCS.)
...
1
39
HITACHI LABEL
1
40 306-952 STRAP (BLACK)
1
41 315-141 TERMINAL SUPPORT (A)
1
* 42 319-933 BATTERY EB 1414 (W/ENGLISH N.P)
1
* 42 320-609 BATTERY EB 1414 (W/ENGLISH N.P)
1 FOR NZL
* 42 320-610 BATTERY EB 1414 ...
Similar Questions
Batteries Will Not Charge
I have a brand new DS 14DVF and the batteries will not charge. The light does not come on with the b...
I have a brand new DS 14DVF and the batteries will not charge. The light does not come on with the b...
(Posted by DanielMVaughn 5 years ago)
I Bought This At A Garage Sale But Realized That The Plug End Of The Battery Cha
I bought this drill at a garage sale and didn't realize the plug end of the battery charger was miss...
I bought this drill at a garage sale and didn't realize the plug end of the battery charger was miss...
(Posted by pattiquick127 6 years ago)
Battery And Charger
Why won't my batteries stay charged for more than a few minutes?
Why won't my batteries stay charged for more than a few minutes?
(Posted by ldm 11 years ago)
Direct Power
how do I work the hitachi cardless driver drill in 12V DC power without battery
how do I work the hitachi cardless driver drill in 12V DC power without battery
(Posted by wondercup101 11 years ago)