Home » Hayward » Pool & Spa » Hayward Super Pump

Hayward Super Pump Support Question

Find answers below for this question about Hayward Super Pump.
Need a Hayward Super Pump manual? We have 2 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by lauracooper on March 27th, 2014

Hayward Super Pump 1 1/2 Hp

Our pump is going to die soon. What should we replace our 1 1/2 hp with to get the best performance and effeciency?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by knlyles on April 17th, 2014 3:15 AM

This answer was accepted by the poster of the original question.

knlyles

Member since:
April 17th, 2014

Points: 2,210

1,110
points

Change Old Bearing With New Ones, Last About 2 Years

stay With 1.5 Hp The Wire And Breaker Size Is For That H.p

Related Hayward Super Pump Manual Pages

All Super Pump models - Page 1

.... ATTENTION INSTALLER - A licensed electrician MUST complete, in full, all electrical installations noted in -ground swimming pool/spa that is a self-priming pump that incorporates an improved seal and impeller design that will provide many years of non-Hayward replacement parts voids warranty. To prevent potential injury and to avoid unnecessary service calls, read this manual...

All Super Pump models - Page 2

... storage. When you see this product. It requires free circulation of the following : Failure to use with hot tubs and spas if so marked. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS To reduce risk of access to the potential for cooling. WARNING - IMPORTANT SAFETY INSTRUCTIONS Before installing or servicing this manual...

All Super Pump models - Page 3

... the limb. The National Electrical Code (NEC) permits use pool or spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached can result in the same plane (i.e. Limb Entrapment- Super Pump™ Series _____ _____ _____ _____ Page 3 of electric shock replace damaged wiring immediately. Run a continuous wire from lawn...

All Super Pump models - Page 4

...HAYWARD GENUINE REPLACEMENT PARTS Stand clear of 15 WARNING - All suction and discharge valves MUST be OPEN when starting system pump, fully open position. WARNING - Separation Hazard. Do not operate pool and spa... lets you see when the basket needs cleaning. ƒ All components molded of the Hayward Super PumpTM Series. Adapts to 48 and 56 frame motors. ƒ Heat resistant, industrial ...

All Super Pump models - Page 5

...The base MUST be tight (but not over-tightened). Super Pump ™ Series__________ Product Specifications _____ Page 5 of short,...access for servicing pump and piping. Pump Location Locate pump as close to water level as possible to pool as practical and ... ONLY HAYWARD GENUINE REPLACEMENT PARTS Do NOT install pump in line. Suction line diameter must : ƒ Allow pump inlet...

All Super Pump models - Page 6

...cause serious or fatal electrical shock hazard. It is reduced considerably; Pool and spa fittings MUST conform to prevent leakage. Fire Hazard. Super Pump ™ Series __________ Pump Mounting (cont'd) _____ Page 6 of the fitting. Electrical WARNING - WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Failure to a gas supply line. Wind the tape...

All Super Pump models - Page 7

.... NEVER OPERATE THE PUMP WITHOUT WATER. Water acts as a coolant and lubricant for more than 110% of swimming pool, spa, or hot tub. NEVER run pump dry. Super Pump ™ Series _...starting motor. ATTENTION - STOP PUMP before it becomes dangerous to pool users. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Run wire from pump and piping system using filter ...

All Super Pump models - Page 8

...pool/spa system. Allowing the pump to explode, with genuine Hayward seal assembly kit. To avoid condensation/corrosion problems, do NOT cover or wrap pump with "Jack's 327" each time it is higher than the pump, unscrew and remove strainer cover; Super Pump...valve after pump is necessary. ƒ Keep motor clean. ATTENTION - All suction and discharge valves MUST be replaced, due ...

All Super Pump models - Page 9

...rotary seal replacement. C. Exercise extreme care in slot at end of this manual for swimming pool pump installation. Slide the motor assembly out of the two-part replacement seal. ... surfaces. Remove the seal plate. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump ™ Series Storing Pump For Winterization Page 9 of the seal assembly is removed of ...

All Super Pump models - Page 10

... assembly onto the impeller hub - Super Pump ™ Series Page 10 of 15 Seal Installation (See Parts Diagram on page 11 of this manual for pump component locations.) 11. Clean and ... holding motor shaft with a clean, soft, cotton cloth. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Place the seal plate onto the motor mounting plate, aligning the tabs on page 11...

All Super Pump models - Page 11

Super Pump ™ Series Replacement Parts Parts Diagram Page 11 of 15 Parts Listing PART NUMBER REFERENCE NUMBER DESCRIPTION NUMBER MODEL MODEL MODEL MODEL ...SPX2600Q SPX2600Q SPX2600Q SPX2600Q 1 SPX0125F SPX0125F SPX0125F SPX0125F SPX0125F SPX0125F 1 SPX1600Z1M SPX1605Z1M SPX1607Z1M SPX1610Z1M SPX1615Z1M SPX1620Z1M WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

All Super Pump models - Page 12

... the skimmer basket and holding your pool dealer can build up causing windings to correct cause of vacuum at the strainer cover (Only your hand over the bottom port with water and cover o-ring is corrected. Low Flow - WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Your Hayward pump motor is felt, check for...

All Super Pump models - Page 13

... at any joint, low water level in pump housing. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Solution: Correct suction condition or throttle return lines, if practical. Super Pump ™ Series Page 13 of filter, valve partially closed (high gauge reading). Solution: Sand filters - Solution: Re-tighten using Teflon tape. 5. Undersized pool piping.

All Super Pump models - Page 14

... improper installation, use in obtaining warranty replacements. For further Hayward dealer or service center information, contact Hayward customer service department. Some states do ...Hayward Pool Products, Inc. 620 Division Street Elizabeth, NJ 07207 ▲Retain this pump, Hayward Pool Products, Inc. Super Pump ™ Series ___ Page 14 of 15 HAYWARD® LIMITED WARRANTY This pump...

All Super Pump models - Page 15

... send me more information on these other products from Hayward: □ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Mail to: Hayward Pool Products, Inc., 620 Division Street, Elizabeth, NJ 07207...

Parts Guide - Page 1

...Prior) 25 8 SPX1700FG 1⁄4" Drain Plug with Gasket (1992 and later) 10 9 SPX2600G1 Mounting Foot with Adapter and Screws 10 - Pumps Super Pump® SP1600X PUMP SERIES (MAX-RATED) REPLACEMENT PARTS Parts for Pump Models: SP1600X5, SP1605X7, SP1607X10, SP1608X10, SP1610X15, SP1611X15, SP1615X20, SP1616X20, SP1621X25 4 6 5 7 16 13 11 12 14 18 17 10 8 2 3 15 9 1 MOUNTING...

Parts Guide - Page 2

... Biguanide Sanitizers NOT Pressure Testable 5 SPX1600S Strainer Cover Gasket 6 SPX1600M Basket 7 SPX1600PN Hand Knob Kit (Includes Swivel Nut and Hand Knob) - Pumps Super Pump® SP2600X PUMP SERIES (MAX-RATED) REPLACEMENT PARTS Parts for 2 1/2 H.P. SPX1600Z52 Mounting Foot Cap Screw (Set of 2 - 1995 and Prior, 2 sets required) 10 SPX1600Z2 Seal Assembly 11 SPX1600F5...