Hayward Salt & Swim Support Question
Hayward Salt & Swim Support Question
Find answers below for this question about Hayward Salt & Swim.Need a Hayward Salt & Swim manual? We have 3 online manuals for this item!
Question posted by mcarroll713 on May 18th, 2016
Salt And Swim Inadequate Water Flow
i have gotten the inadequate water flow mesage on the led indicator and followed all steps listed in the manual and the message is still there. What else can I check or do to determine the problem?
Current Answers
Related Hayward Salt & Swim Manual Pages
Salt & Swim Owner's Manual - Page 1
092463 RevA
Salt & SwimTM
Chlorine Generator for Inground Swimming Pools up to 25,000 gallons
Owner's Manual
Contents
Introduction 1 Installation 2-8 Operation 12-14 Troubleshooting........15 Warranty 21 DIY-12 DIY-6
Hayward Pool Product 620 Division Street, Elizabeth, NJ 07207
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Salt & Swim Owner's Manual - Page 3
... of a saline water purification system in the pool water. The Salt & Swim requires a low concentration of byproducts that is NOT to be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of most residential swimming pools up to 25,000 gallons only. Dry acid can cause a buildup of salt (sodium chloride) in a pool or spa using natural stone...
Salt & Swim Owner's Manual - Page 4
...to the following sections for Salt & Swim operation, the pool's chemistry must be balanced and salt must be installed. Salt & Swim Installation
Follow the step by the manufacturer, its service agent or similarly qualified persons in accordance with Local and NEC codes. Adding Salt: Add salt several hours, so start the procedure well before starting this manual. Refer to the pool, per...
Salt & Swim Owner's Manual - Page 5
... at the end of the return
piping just before the water returns to the pool.
Screw in a raintight enclosure that is suitable for outdoor mounting. All pool equipment should be enough clearance to block the four sides of the Control Box.
Do not mount Salt & Swim inside the box), it is mounted.
After ma rkin...
Salt & Swim Owner's Manual - Page 8
... gauge (8 AWG) solid copper wire from the bonding lug to Pool Bonding loop 6 Run pump for 5 minutes and check for leaks. Cell Cap
Retaining Nut
Bonding
Pool bonding or "equipotential bonding" ensures that all pool components around the pool are at the bottom of the Salt & Swim enclosure. to your location (see Local and NEC codes), a bonding...
Salt & Swim Owner's Manual - Page 9
... INADEQUATE WATER FLOW LED and a solid STANDING BY LED. GFCI OUTLET
After being powered on your pool. The Salt & Swim should now display a solid INADEQUATE WATER FLOW and a solid STANDING BY LED. Flow Switch Calibration Procedure
IMPORTANT: Before going any further, the pool water must be balanced and salt must be added to your filter pump and begin normal operation. Follow...
Salt & Swim Owner's Manual - Page 10
... indicator of the pool water "balance". Have your water tested or use : Measure pool pH, temperature, calcium hardness,
and total alkalinity. Water Chemistry
The table below to determine the saturation index.
Use the chart below summarizes the levels that are recommended by The Association of pH, Ti, Ci and Ai
into the water. Your Authorized Salt & Swim Dealer or most pool...
Salt & Swim Owner's Manual - Page 11
... available in low chlorine production.
Do not use water conditioning salt pellets, however, it will begin to give a salty taste to your pool is constantly recycled and the loss of salt throughout the swimming season should be small.
Use the chart on page 11 to determine how much salt in pounds or (Kgs) need to be added...
Salt & Swim Owner's Manual - Page 12
POUNDS and (Kg) of SALT NEEDED FOR 3200PPM
Current salt
Gallons and (Liters) of Pool Water
level
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 25,000
ppm (30,000) (37,500) (...
Salt & Swim Owner's Manual - Page 14
... flow or low flow through the Cell.
When you have an abnormally high bather load, a large
amount of rain, a cloudy water condition, or any other
condition which requires a large amount of chlorine being generated. When this manual. The pool filter pump could be in its expected life.
The DAILY CHLORINE OUTPUT LEDs above these buttons will indicate...
Salt & Swim Owner's Manual - Page 15
... is higher than 12 minutes) when the pool water is 50º - 60ºF. The Salt & Swim stops generating when the pool water temperature drops below 50ºF. There should be lit. When the routine is first applied to the Salt & Swim, an initialization routine will generate: 1. For pools with 5 DAILY CHLORINE OUTPUT LEDs illuminated. Daily Chlorine Output Setting
You...
Salt & Swim Owner's Manual - Page 16
... gloves and appropriate eye protection. Most pools require less chlorine during cold weather: Check chlorine levels periodically. In areas where water is not corrected, you may have to periodically clean the Cell. Be sure to one gallon of Vessel. If any freezing conditions occur.
Maintaining the Salt & Swim System
The replaceable Cell uses the same...
Salt & Swim Owner's Manual - Page 17
... no flow condition and has stopped generating chlorine. - The system will not resume operation until the water temperature returns to shut down because the temperature of days before the pool returns to be reset. 3. Common Problems and Solutions
The Salt & Swim's various LEDs show the desired 1-3ppm free chlorine reading. 2. Some indications may be a matter of the pool/spa water is...
Salt & Swim Owner's Manual - Page 18
... is free to the Control Box is blinking The Salt & Swim may be too low. CELL LIFE LOW LED illuminated The Cell has reached the end of the DAILY CHLORINE OUTPUT LEDs. If the condition persists, remove the Cell from the Vessel and check that the flow switch is scaled, follow the directions
on the diagram below .
Salt & Swim Owner's Manual - Page 19
... power to the Salt & Swim by moving water. 4. Contact Hayward Technical Service. LED 3
1. Contact Hayward Technical Service. Contact Hayward Technical Service.
17 LED 7
1. If dirty, follow the Cell cleaning procedure. 3. LED 8 LED 9
1. Inspect the Cell Vessel and verify the Cell plates are fully covered by unplugging the linecord for two minutes
Inadequate and then...
Salt & Swim Owner's Manual - Page 23
... product. Damage resulting from failure to maintain pool water chemistry in accordance with the recommendations contained in the owners manual(s). 4. Problems resulting from failure to install, operate or ... CELL PURCHASED FROM HAYWARD. Operational hours are defined to a pool or spa, war or acts of the Salt & Swim product. Hayward warrants all accessories and other replacement parts for ...
Salt & Swim Installation Quick Start Guide - Page 1
... PVC pipe You have balanced your pool chemistry and have 3200ppm salt in your pool (see Chemistry Quickstart Guide)
Installation Preparation Read this entire Quickstart Guide Remove power to filter pump Drain water from the pool. The Control Box will also have read the safety precautions in the owner's manual
Overview
Spread out parts on ground...
Salt & Swim Installation Quick Start Guide - Page 2
... to install the Nut Assembly. The Salt & Swim should now display a solid INADEQUATE WATER FLOW and a solid STANDING BY LED. Salt & SwimTM Installation Quick Start Guide
STEP 2: Determine where Cell Vessel will be installed
The Cell Vessel must fit on your filter pump and begin normal operation.
092464 RevB STEP 3: Install Nut Assembly
Follow the procedure below to aid in Linecord...
Salt & Swim Chemistry Quick Start Guide - Page 1
... YOU FOLLOW THE STEPS IN THE ORDER PRESENTED. For non-standard shaped pools, it may be easier to the pool with the suction coming from corrosion of metal pool parts, staining of the total alkaline substances found in the pool water.
RECOMMENDED LEVEL: 2700 - 3400 ppm (3200 ppm ideal)
After testing salt, refer to Table 1 to determine how much salt...
Salt & Swim Chemistry Quick Start Guide - Page 2
Table 1
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Current salt
Gallons and (Liters) of Pool/Spa water
level
12,000 14,000 16,000 18,000 20,000...500)
1
(0)
2
(0.06)
3.2
(0.1)
4.2
(0.13)
5.2
(0.16)
6.2
(0.2)
7.2
(0.23)
8.4
(0.26)
9.4
(0.3)
10.4
(0.32)
Gallons and (Liters) of Pool Water
1,000 5,000 10,000 15,000 20,000 25,000 (3,750) (19,000) (38,000) (57,000) (75,000) (95,000)
2.5
(0.08)
5
...
Similar Questions
Salt And Swim 3c Cell Cap Leaking
Water is coming out of my salt and swim 3c from the cell cap. What could be the issue here?
Water is coming out of my salt and swim 3c from the cell cap. What could be the issue here?
(Posted by michellebrenner62 6 years ago)
Inadequate Water Flow Light Blinking
I have a problem with my Salt and swim I just installed after the calabration the Inadequate Water F...
I have a problem with my Salt and swim I just installed after the calabration the Inadequate Water F...
(Posted by haufbraudrinker 9 years ago)
No Pressure On Psi Gage. Low Flow New Pump Have Tried Troubleshooting In Manual.
(Posted by pavethewayconcrete 11 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)