Hayward Salt & Swim Support Question
Hayward Salt & Swim Support Question
Find answers below for this question about Hayward Salt & Swim.Need a Hayward Salt & Swim manual? We have 3 online manuals for this item!
Question posted by jabcoreye on August 26th, 2014
How To Manually Set Salt Level In Swimpure
The person who posted this question about this Hayward product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hayward Salt & Swim Manual Pages
Salt & Swim Owner's Manual - Page 1
092463 RevA
Salt & SwimTM
Chlorine Generator for Inground Swimming Pools up to 25,000 gallons
Owner's Manual
Contents
Introduction 1 Installation 2-8 Operation 12-14 Troubleshooting........15 Warranty 21 DIY-12 DIY-6
Hayward Pool Product 620 Division Street, Elizabeth, NJ 07207
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Salt & Swim Owner's Manual - Page 2
...) horizontally from lawn
mowers, hedge trimmers, and other equipment.
•
WARNING - Connect only to electric supply; To reduce the risk of the
hot tub or spa to
use an extension cord." provide a prop-
When installing and using this product unless they are provided on the external surface or on the inside...
Salt & Swim Owner's Manual - Page 3
... a saline water purification system in a pool or spa using natural stone for coping or for inground swimming pools up to bather load, rainfall, temperature, and the pool's cleanliness. NOTE: Before installing this product as part of stone used with above ground pools or with electronic chlorine generator in your pool. Introduction
The Salt & SwimTM is an automatic chlorine...
Salt & Swim Owner's Manual - Page 4
... the Cell Cap connector pins while handling the Salt & Swim unit during installation. Salt & Swim Installation
Follow the step by the manufacturer, its service agent or similarly qualified persons in accordance with Local and NEC codes. Take care to exceed the recommended salt level. Some adjustments to your pool water, follow the instructions on the Installation Quick...
Salt & Swim Owner's Manual - Page 5
... more, if local codes require) from the pool, within 3ft from a GFCI outlet, and within 15ft from the Cell Vessel. Use this tem pla te, scre w in t op fasten ers le aving
1/ 8" spa ce be
upstream from where the Cell is installed. Do not mount Salt & Swim inside the box), it is important not...
Salt & Swim Owner's Manual - Page 8
... as shown below. to your location (see Local and NEC codes), a bonding lug is provided at the same electrical potential. Cell Cap
Retaining Nut
Bonding
Pool bonding or "equipotential bonding" ensures that all pool components around the pool are at the bottom of the Salt & Swim enclosure.
Salt & Swim Owner's Manual - Page 9
... pump OFF. 2. Keep the Salt & Swim powered for Salt & Swim operation. Turn the filter pump OFF. 5. Flow Switch Calibration Procedure
IMPORTANT: Before going any further, the pool water must be balanced and salt must be added to Step 3. 3.
The Flow Switch Calibration procedure will not perform this manual for information on your pool water for the remainder of...
Salt & Swim Owner's Manual - Page 10
...Salt & Swim chlorine generator. Insert values of Pool and Spa Professionals (APSP). Water Chemistry
The table below to determine the saturation index.
Your Authorized Salt & Swim Dealer or most pool...
2.5
800
2.9
How to use pool water test strips and refer to adjust the water chemistry as well. Use the chart below summarizes the levels that are recommended by The Association ...
Salt & Swim Owner's Manual - Page 11
... to determine how much salt in the pool and add salt according to use rock salt, salt with yellow prussiate of about 3500-4000 ppm).
bags labeled "Coarse Solar Salt" or "Pool Salt". Turn the circulating pump on the bottom of salt throughout the swimming season should be small. Always check stabilizer (cyanuric acid), when checking salt. Salt Level
Use the chart on...
Salt & Swim Owner's Manual - Page 12
POUNDS and (Kg) of SALT NEEDED FOR 3200PPM
Current salt
Gallons and (Liters) of Pool Water
level
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 25,000
ppm (30,000) (37,500) (45000) (...
Salt & Swim Owner's Manual - Page 15
...Salt & Swim unit. When the routine is perfectly normal and does not require any input from the Salt & Swim unless pool components are being serviced or the pool will illuminate. Push "+" to increase and "-" to decrease the current setting...to be lit. If the water chemical levels are in the pool passes through the filter at all times. For pools with 5 DAILY CHLORINE OUTPUT LEDs illuminated...
Salt & Swim Owner's Manual - Page 16
...Salt & Swim Cell
Unplug the Salt & Swim from the GFCI outlet and remove power from the Vessel by freezing water just as this self cleaning action will not remove the majority of Vessel. The simplest way to avoid this is not corrected, you may need to lower the setting when the pool...and return lines before attempting to the recommended levels as the popular Hayward Turbo Cell. Once...
Salt & Swim Owner's Manual - Page 17
... that the GFCI outlet is too low - Salt level too high - Cold water between 50ºF - 60ºF causes Salt & Swim to illuminate. The temperature coming out of the heater and into the Cell could possibly be high enough to shut down because the temperature of the pool/spa water is running .
Filter pump time too...
Salt & Swim Owner's Manual - Page 18
...AND MAX LED blinking There is scaled, follow the directions
on the diagram below . The salt level may display an error by illuminating the PROBLEM DETECTED LED and blinking one of its life...that the wire to recommended levels. - PROBLEM DETECTED LED illuminated AND MIN LED blinking - Replace as soon as possible 6. Adjust salt to the Control Box is blinking The Salt & Swim may be too low....
Salt & Swim Owner's Manual - Page 19
... fully covered by unplugging the linecord for two minutes and then plugging it back in the pool is receiving 120VAC input. 3. MAX LED
1. Verify that the salt level in . 2. Contact Hayward Technical Service. Recycle power to the Salt & Swim by unplugging the linecord for two minutes and then plugging it back in . 2. Contact Hayward Technical...
Salt & Swim Owner's Manual - Page 23
... failure to maintain pool water chemistry in accordance with the recommendations contained in the owners manual(s). 3. Problems resulting... of natural stone used in or immediately adjacent to a pool or spa, war or acts of purchase or the nearest Hayward authorized...LIMITED WARRANTY (effective 03/01/12) Hayward warrants its Salt & Swim chlorination products to be free of defects in materials and...
Salt & Swim Installation Quick Start Guide - Page 1
...manual) You have a saw suitable for cutting PVC You have tools for mounting the Control Box (drill, drill bits, screwdriver) You have a permanent marker to mark the PVC pipe You have balanced your pool... Remove power to filter pump Drain water from the pool.
Salt & SwimTM Installation Quick Start Guide
Before you begin
Pre-Installation Checklist Pool is less than 25,000 gallons There is at ...
Salt & Swim Installation Quick Start Guide - Page 2
... will be installed
The Cell Vessel must fit on for the first time, the Salt & Swim will not fit.
You can be the very last component installed in marking and cutting the pipe. Use the included Cutting Template to the pool. Secure the Template and use a permanent marker to install the Nut Assembly.
Salt & Swim Chemistry Quick Start Guide - Page 1
... x Average Depth x 785
Length x Width x Average Depth x 893
STEP 2: Adjust Salt Level
IDEAL RANGE: Before adding salt, test your pool. This calculation will cause the pool water to become corrosive.
Brush the salt around to speed up on . Use common food quality salt usually available in your pool's water chemistry must be properly balanced. It's a mild acid that...
Salt & Swim Chemistry Quick Start Guide - Page 2
Table 1
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Current salt
Gallons and (Liters) of Pool/Spa water
level
12,000 14,000 16,000 18,000 20,000 22,000 24,000
ppm (45,000) ...Dilute Dilute Dilute
Table 2
POUNDS and (Kg) OF STABILIZER (CYANURIC ACID) NEEDED FOR 80 PPM
Current Stabilizer
level
Gallons and (Liters) of Pool Water 8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000
(...
Similar Questions
Can You Install Hayward Swimpure Salt Cell In Vertical Position
(Posted by bresist 9 years ago)
Gold Line Display
my display on aqua rite gold line salt generator no longer shows salt level or temp
my display on aqua rite gold line salt generator no longer shows salt level or temp
(Posted by rhockey35 10 years ago)
How Do I See The Salt Level Display On The Screen Again?
How do I get the panel to display the salt level again? The diagnostic button goes through all sorts...
How do I get the panel to display the salt level again? The diagnostic button goes through all sorts...
(Posted by randiledingham 10 years ago)
How To Set Salt System To 0
(Posted by Anonymous-76786 11 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)