Hamilton Beach HBH650 Support Question
Hamilton Beach HBH650 Support Question
Find answers below for this question about Hamilton Beach HBH650 - Bar Blender - Tempest 64oz.Need a Hamilton Beach HBH650 manual? We have 1 online manual for this item!
Question posted by darrylculver on April 7th, 2014
Have A Dual Blade Blender And 1 Turns Very Hard.
a type B48 blender with 2 cutters and one spins freely while the other turns very hard. What is the solution?
Current Answers
Related Hamilton Beach HBH650 Manual Pages
Operation Manual - Page 2
... your operator training program. SAVE THESE INSTRUCTIONS -
2 If cutter assembly blades are sharp. Do not use .
12. To prevent damage to repair or tighten cutter assembly.
20. Blender Safety
IMPORTANT: This operation manual should be damaged if inadvertently turned on top of 3 minutes.
23. When using blender. Read the Operation Manual before cleaning or servicing.
7. To...
Operation Manual - Page 3
... utensils in burns.
Empty container. 2. Wipe exterior with soft cloth dampened with clean water.
Electrical Shock Hazard Disconnect power before cleaning blender base. Failure to remove any moisture from the cutter assembly. 5. Fill container with sanitizing solution, replace lid
and filler cap and run on the bleach. 1. We recommend keeping a replacement container and...
Operation Manual - Page 4
... Speed Jump Cycle 4
Cutter Assembly Jar Pad
5 10 15 20
STOP
25 30 35
40
POWER
HIGH
LOW
JUMP
PULSE
Control Panel
Jar Pad Indicator Motor Temperature
Power ON (I)/OFF (O)
Pulse
Parts and Features
The parts and features for blending and mixing beverages. Your Tempest blender is designed for the Tempest blender are shown on...
Operation Manual - Page 5
...desired function (HIGH, LOW or JUMP). Press the Power ON (I)/OFF (O) button to turn the blender ON (I ).
6. The red LED lamp indicates that power is OFF (O). Power ...
2. Depending on a dry, level surface.
3. Make sure the power switch is ON (I ). Plug the blender into a grounded 3-prong electrical outlet.
4. Adjust the timer knob to meet power requirements:
120 VAC, 60Hz
230...
Operation Manual - Page 10
Thermal Overload Protection
1
2
3
4
5
6
00:00 Remove jar within
:03
10
00:02:00
Blender will automatically turn off after 2 minutes of low-speed "cool down cycle".
Operation Manual - Page 11
Replacing the Cutter Assembly
1
2
3
4
5
6
11
Operation Manual - Page 12
.... Do not fill past highest graduation marking.
• Cutter assembly blades are not sharp or are loose, discontinue use immediately and replace the blades.
See "Thermal Overload Protection" for shorter cycle times. Replace if necessary.
Solution . . .
• Make sure that the jar is too full. Blender fails to cool until temperature light is overheating. Attempt...
Operation Manual - Page 13
...warranty with respect to parts subject to wear, including without limitation: motor brushes, container and cutter assembly, clutches, bristle brushes, funnel, stainless steel cup, agitators, carafes, etc.
Follow ...or consequential damages, so the foregoing limitations may also have model, series, and type numbers ready for paying shipping and handling charges to return the product to us...
Similar Questions
My Blender Stopped Working Light Turns On But Blender Don't Blend.
(Posted by aminjiwan 10 years ago)
Hamilton Beach Smoothie Blender Quits Working After Only 6 Weeks Of Use.
I am so frustrated!! Put the liquid ingredients in my blender, then added 5 ice cubes. The on light ...
I am so frustrated!! Put the liquid ingredients in my blender, then added 5 ice cubes. The on light ...
(Posted by helin 10 years ago)
Hamilton Beach Blender Replacement Blade
Can I get a replacement blade for my Hamilton Beach blender model #52300 Type B36?
Can I get a replacement blade for my Hamilton Beach blender model #52300 Type B36?
(Posted by spiritwolf78 11 years ago)
Hamilton Beach Single Serve Blender
If my Hamilton Beach single serve blender will not turn on when I first try to use it, what can I do...
If my Hamilton Beach single serve blender will not turn on when I first try to use it, what can I do...
(Posted by WaveCrest1992 11 years ago)
Blender Not Working
nothing happens on my blender when I push the buttons. Motor seems to be ok am able to spin freely. ...
nothing happens on my blender when I push the buttons. Motor seems to be ok am able to spin freely. ...
(Posted by redhotanirish 11 years ago)