Hamilton Beach HBH650 Support Question
Hamilton Beach HBH650 Support Question
Find answers below for this question about Hamilton Beach HBH650 - Bar Blender - Tempest 64oz.Need a Hamilton Beach HBH650 manual? We have 1 online manual for this item!
Question posted by helin on September 27th, 2013
Hamilton Beach Smoothie Blender Quits Working After Only 6 Weeks Of Use.
I am so frustrated!! Put the liquid ingredients in my blender, then added 5 ice cubes. The on light came on, but when I pushed the auto smoothie button, the thing died. I have found many similar costomer complaints about this product. I want my money back!!!
Current Answers
Related Hamilton Beach HBH650 Manual Pages
Operation Manual - Page 2
.... Handle carefully.
19. Do not leave blender unattended while it is intended for other hot liquids.
11. When using blender. To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly, DO NOT insert utensils into a grounded 3-prong outlet.
3. Do not use by Hamilton Beach may push lid off parts.
8. To reduce risk...
Operation Manual - Page 3
... burns.
Immerse lid and filler cap in container when blending.
Part Description 64 oz. Failure to use an extension cord. Friday www.commercial.hamiltonbeach.com
Replacement Parts
The following components are subject to remove... minutes. 4. Electrical Shock Hazard Disconnect power before cleaning blender base. We recommend keeping a replacement container and cutter on hand. Do not...
Operation Manual - Page 4
Your Tempest blender is designed for the Tempest blender are shown on this page. Become familiar with all parts and features before using your blender. Polycarbonate Container
Blender Base
Reset Switch/ Circuit Breaker
Control Panel
Timer Knob*
*
= 3 Min.
Parts and Features
The parts and features for blending and mixing beverages. Removable Filler Cap
...
Operation Manual - Page 5
... with ingredients and container lid in place.
5. Adjust the timer knob to meet power requirements:
120 VAC, 60Hz
230 VAC, 50Hz
230 VAC, 50Hz
Ground prong
Blender Operation - Read Important Safety Instructions and Warnings before use.
2. The red LED lamp indicates that power is OFF (O). Quick Start Guide
1. Press the Power ON (I)/OFF (O) button...
Operation Manual - Page 10
Thermal Overload Protection
1
2
3
4
5
6
00:00 Remove jar within
:03
10
00:02:00
Blender will automatically turn off after 2 minutes of low-speed "cool down cycle".
Operation Manual - Page 12
....
• Check to see if cutter assembly is properly positioned, the light will go off.
• Blender will not mix properly
• Check to create a fluid blend. Replace if necessary. Blender fails to the ingredients. Maintenance
Inspect the blender and its various parts and replace as follows:
Daily Weekly
Unplug the blender and remove the container from...
Operation Manual - Page 13
... and cutter assembly, clutches, bristle brushes, funnel, stainless steel cup, agitators, carafes, etc. Hamilton Beach Commercial will make an initial phone diagnosis. Friday 8:00 AM - 5:00 PM EST). Step ...AND ALL CLAIMS FOR SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. Always use not in accordance with the printed directions. If it 's under this product in...
Similar Questions
My Blender Stopped Working Light Turns On But Blender Don't Blend.
(Posted by aminjiwan 10 years ago)
Have A Dual Blade Blender And 1 Turns Very Hard.
a type B48 blender with 2 cutters and one spins freely while the other turns very hard. What is the ...
a type B48 blender with 2 cutters and one spins freely while the other turns very hard. What is the ...
(Posted by darrylculver 10 years ago)
Hamilton Beach Single Serve Blender
If my Hamilton Beach single serve blender will not turn on when I first try to use it, what can I do...
If my Hamilton Beach single serve blender will not turn on when I first try to use it, what can I do...
(Posted by WaveCrest1992 11 years ago)
Blender Not Working
nothing happens on my blender when I push the buttons. Motor seems to be ok am able to spin freely. ...
nothing happens on my blender when I push the buttons. Motor seems to be ok am able to spin freely. ...
(Posted by redhotanirish 11 years ago)
Blender Stopped Working
Hi, The blender is not working at all. After plugging it to the power tried to start the base only ...
Hi, The blender is not working at all. After plugging it to the power tried to start the base only ...
(Posted by sunmun19 12 years ago)