Hamilton Beach 19804 Support Question
Hamilton Beach 19804 Support Question
Find answers below for this question about Hamilton Beach 19804.Need a Hamilton Beach 19804 manual? We have 1 online manual for this item!
Question posted by jkgsing on June 26th, 2021
My Iron Light Won't Turn On
The person who posted this question about this Hamilton Beach product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Odin on June 27th, 2021 12:49 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Move or tilt the iron to reset it. If that doesn't solve, consider the other suggestions for the first-listed PROBLEM at https://www.manualslib.com/manual/509859/Hamilton-Beach-19804.html?page=12.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/hamilton%20beach.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/hamilton%20beach.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Hamilton Beach 19804 Manual Pages
Use & Care - Page 2
...wattage appliance. 12. To avoid the risk of electric shock when the iron is stable. 9. Do not let the cord touch hot surfaces. The iron must be taken to a qualified serviceman for any appliance used . ... the same circuit with an ampere rating equal to OFF before putting the iron away. Use caution when you turn the iron to or greater than the maximum rating of damage or it cannot be ...
Use & Care - Page 3
...12 11:53 AM This will stop and does not indicate a defect or hazard.
• Many irons spit or sputter during the first few uses with tap water. Shock Hazard: This appliance has a ... the steam chamber becomes conditioned. Then follow the self-cleaning instructions on an ironing board. Press the Steam Burst button several times to smoke. Other Consumer Safety Information
This product is...
Use & Care - Page 5
... 5
Optional feature on select models.
NOTICE: Do not unwind the cord past the red tape. Allow 2 minutes for iron to retract the cord.
5
To turn iron off automatically when left in the following positions. The light will reset the Auto Shutoff sensor. 5
11/12/12 11:53 AM
Grabbing the plug, pull out the...
Use & Care - Page 6
... dripping from the soleplate.
6
Set Adjustable Steam Switch to reach maximum temperature. Optional feature on a lower temperature setting or failing to allow the iron to preheat for iron to the desired steam level.
11/12/12 11:54 AM NOTICE: Do not unwind the cord past the red tape.
How to Steam...
Use & Care - Page 7
... release the Steam Burst Button to touch delicate garments. The light will reset the Auto Shutoff sensor. 7
840221700 ENv02.indd 7
11/12/12 11:54 AM POSITION SENSING/AUTO SHUTOFF
The iron will turn off automatically when left in the following directions in "Care and Cleaning."
8
To turn iron off, set Adjustable Steam Switch to (Dry...
Use & Care - Page 8
... their meaning.
Fabric Setting Chart
NOTICE: To avoid garment damage, check garment label for fabric composition and ironing instructions. Garment Label Symbols
Fabric care labels on wrong side. Iron
High
Medium Low Temp
Temp
Temp
Setting
Setting
Setting
Do not iron
Do not use spray. Steam Setting
Dry Iron
Temperature Setting
OFF
Synthetics
•
Low
Silk, Wool...
Use & Care - Page 9
... of the soleplate. Check the soleplate (the surface of the ironing board, stand with the iron. not with your ironing board to ironing. • Any portion of a garment that meets the fabric) for faster, easier ironing. When pressing, the iron is helpful to increase the recommended iron temperature when using small strokes of your elbows bent at right...
Use & Care - Page 10
... tilt pointed end of the soleplate. Soleplate Care
To clean an iron's soleplate, preheat the iron to the highest temperature setting and iron over zippers, buttons, pins, metal rivets, or snaps, since they... creates heavy steam that transfers grime from the flat surface of iron over sink until water runs out.
3
Do not store iron laying flat on the soleplate. steam can burn.
10
NOTICE:...
Use & Care - Page 11
...-Clean Feature
To keep the steam vents clear of any buildup, follow these instructions each time you iron using steam.
1
2
3
4
Press Temperature Settings Button until COTTON/LINEN is illuminated.
The light will stay on until iron is unplugged.
5
Hold iron over sink.
840221700 ENv02.indd 11
6
Press and hold the Self-Clean Button until...
Use & Care - Page 12
...? Water left in a lamp. • Has a temperature been selected? • Is the Auto Off light illuminated? Did the iron have enough time to preheat? • If dry ironing, make sure the Adjustable Steam Switch is in the (Dry Iron) position. • Check water level. • Is the Adjustable Steam Switch in the (Steam) position...
Similar Questions
My Hamilton Beach 14211 Iron Lights Up But Will Not Heat Up
(Posted by haroldjhowell 1 month ago)
My Iron Is Getting Too Hot When It Is Switched On
iron is getting too hot when it is switched on
iron is getting too hot when it is switched on
(Posted by ahuja123 4 years ago)
It Won't Let Me Turn On When I Push The Light Goes Up And Then Just Goes Right B
It won't let me turn on when I push the light goes up and then just goes right back off
It won't let me turn on when I push the light goes up and then just goes right back off
(Posted by Caharris5 6 years ago)
Self Cleaning For Hamilton Beach Model 19804 Iron
The user manual does not address the procedure for "self cleaning", it just tells the location of th...
The user manual does not address the procedure for "self cleaning", it just tells the location of th...
(Posted by cwwidner 7 years ago)
The Iron Won't Heat Up And The Reset Light Does Not Turn On.
I inadvertently left the iron on for several days. The iron will no longer heat up. The unit lights ...
I inadvertently left the iron on for several days. The iron will no longer heat up. The unit lights ...
(Posted by ed4tennis 11 years ago)