GE NX-1448E Support Question
GE NX-1448E Support Question
Find answers below for this question about GE NX-1448E - Security NetworX 48-Zone Fixed.Need a GE NX-1448E manual? We have 1 online manual for this item!
Question posted by gg on February 12th, 2012
Battery Location For Nx-1448e
Power on keypad is flashing. Manual says to change the battery...WHERE IS THE BATTERY??
Current Answers
Related GE NX-1448E Manual Pages
User's Manual - Page 2
SECURITY SYSTEM NOTES
Installing/Service Company For Service Call Central Station
Duress Code
This system is
is not
partitioned. EMERGENCY ACTIVATION KEYS (check if enabled)
Fire
Auxiliary Emergency
Police
Abort Delay (s) Auto Bypass (s) Auto Instant Battery Test
PROGRAMMED FUNCTIONS Cancel Alarm Change Partitions Chime Communicator Test
Forced Arming (s) Group Bypass (s) Quick...
User's Manual - Page 4
... help you do so could result in this manual you have of your system. Page 4
NX1448E Icon Keypad All users of the security system and how that knowledge is described in ...security. Your security system is an electronic device and is furnished to turn on it as your single source of security devices attached to 60 icons and a built-in an accessible location for your security...
User's Manual - Page 5
... connected and adequately charged. Your system will need to be possible to arm the security system without power.
Warning devices will not work without the backup battery connected. Care should be taken to plug in all situations.Use qualified security professionals to provide notification of an alarm event. Please read the following information and...
User's Manual - Page 6
... INSTANT ICON 12 LISTEN-IN ICON 12 POWER ICON 12 READY / NOT READY ICON 12 SILENCED ICON 12 STAY LIGHT 12 TAMPER/TROUBLE ICONS 12 ZONE ICON 12 KEYPAD FUNCTIONS 13 ARMING YOUR SYSTEM IN THE ..."AWAY" MODE 13 ARMING YOUR SYSTEM IN THE "STAY" MODE 14 USING THE QUICK ARM 15 CHANGING MODES WHILE SYSTEM IS ...
User's Manual - Page 7
... EVACUATION PLANS 26
NX1448E Icon Keypad
Page 7 (Table of Contents continued...)
DISARMING THE SYSTEM 15 CANCEL / ABORT FEATURE 16 BYPASSING ZONES 16 GROUP BYPASS 16 UNBYPASSING 17 TURNING THE DOOR CHIME ON AND OFF 17 CHANGING USER CODES 17 ASSIGNING USER CODE AUTHORITY LEVELS 18 OTHER KEYPAD FUNCTIONS 20 SETTING THE KEYPAD TONE 20 CHANGE PARTITION -
User's Manual - Page 8
The location where alarm data is opened. ... without an alarm, or before entering a user code to disarm.
NX1448E Icon Keypad An option that allows the keypad to sound a ding-dong whenever an entry/exit door is sent during an ... multiple zones with one or more zones open. The level of the two. A system that is ready to be "force armed" will flash the ready icon. (Note: Those zones that ...
User's Manual - Page 9
... digit entry code used to turn on (ARM) the security system by pressing either the [STAY] or [EXIT] key on the keypad control (for ARMING only) as programmed by the installing ...Power Service
Instant Enter Code Trouble FIRE Silenced Tamper
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
NX1448E Icon Keypad...
User's Manual - Page 10
... be programmed for these keys only in an emergency situation that center. This key can be sent to the Panic/Hold-Up activation. If your security system will respond to that requires response by emergency personnel.
Page 10
NX1448E Icon...
User's Manual - Page 11
...LIGHT
The exit light is bypassed. NX1448E Icon Keypad
Page 11 BYPASS LIGHT
The bypass light is "on" when any zone in this light is armed. It will flash during the exit delay. CHIME LIGHT
The ...to prevent an alarm. If the bypass light is disarmed.
Please note that a fire zone is flashing in a trouble condition. The user may want to disarm the system if the exit light is in...
User's Manual - Page 12
... battery condition. SILENCED ICON
The silenced icon appears after a code has been entered to force arm. If a zone icon is "flashing" rapidly, it means that zone is armed. Page 12
NX1448E Icon Keypad LISTEN-IN ICON
Listen-in icon is on when an NX-534 is delayed.
ZONE ICON
The zone icons are bypassed. If a zone icon is "flashing", that...
User's Manual - Page 13
... arm if the not ready icon is on or flashing. • If the power icon is off, you have no AC power. Trouble conditions are: Tamper Hardware
Low Battery
Loss of Supervision
(A combination of Alarm/Fault and Tamper/Trouble will flash rapidly for service. NOTE: If any zones are secure. NOTE: The exit light will produce a rapid...
User's Manual - Page 14
... 14
NX1448E Icon Keypad Step 3
• Press the [STAY] key. • The stay light will illuminate indicating that all protected zones and
sensors are bypassed, a sensor in that zone can be on or flashing when all interior zones are bypassed.
Step 2
• Enter your installing company listed on or flashing. • If the power icon is enabled...
User's Manual - Page 15
... the [EXIT] key, or arm in your
NX1448E Icon Keypad
Page 15 The security system is flashing during the entry delay, the alarm system has been activated in the STAY mode by pressing the [STAY] key again. You may be off (toggle) all designated interior zones. (Optional) When armed, pressing the [EXIT] key will...
User's Manual - Page 16
... zone 1, press [1]-[2] for bypassing zones:
Step 1 Step 2 Step 3
Step 4 Step 5
Step 6
Press the [BYPASS] key. Repeat steps 3 and 4 for any other zone(s) that are used for zone 12. Page 16
NX1448E Icon Keypad ... police from a safe location.)
CANCEL / ABORT FEATURE (Optional, see page 1)
The cancel light will stop flashing upon exiting the Bypass Mode. BYPASSING ZONES
If you wish to come...
User's Manual - Page 17
...
The Enter Code icon will flash.
NX1448E Icon Keypad
Page 17
N For partitioned systems, someone changing the code of
another person ...must be illuminated.
If the chime is in the disarmed state. Each press of the "user code". The Ready icon will display. UNBYPASSING To manually unbypass zones...
User's Manual - Page 21
... created alarms and will display. Step 2
The ALARM MEMORY feature will flash those zones that were bypassed during the last alarm. Alarms and reports will not be sent, unless a communicator test is performed at which time a test signal will perform a battery test, communicator test, and/or a siren test. Step 1 Step 2
Press [r]-[7]. Wait a few...
User's Manual - Page 23
...flashing, one or more zone icon(s) will be on ", press [r]-[2] to the system fault(s) below:
1 Over Current Fault 2 Siren Trouble 3 Box Tamper
5 Expander Low Battery 6 Expander Box Tamper 7 Expander Trouble
4 Expander Power...of what service(s) is troubled, the trouble icon will flash and the zone icon(s) will be on " if the security system requires service. Press the [#] key to return to...
User's Manual - Page 24
... affect all partitions of power and your system and the
central station. * SEE NOTE AT END OF TABLE.
8
LOSS OF SYSTEM TIME - 3
ZONE LOW BATTERY - The zone icon(s) will illuminate showing which zone(s) has a low battery.
Press the [3] key. This only
applies to wireless zones. Page 24
NX1448E Icon Keypad Press the [4] key and the zone
icon(s) will
illuminate...
User's Manual - Page 25
... for all keypresses. beeps rapidly for any zone(s) are detected: Zone or Box Tamper, Low Battery, AC Power Fail, or Expander trouble. and beeps 1 second at the end of an exit delay; Pulses when the armed status changes and a low battery is built into the keypad.
Please contact your system keypad may sound for the last 10 seconds...
User's Manual - Page 26
... 26
NX1448E Icon Keypad Draw up a floor plan of your escape time. Always keep these routes free from each room. An escape ladder may be a window that can be located near the window if....
One will increase your home. If you think it is best achieved by the installation of fire detection equipment in . The following steps are examples of your Security System has been completed,...
Similar Questions
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)
How To Get Rid Of Function Errors On A Nx-148e Lcd Keypad
(Posted by brmn 9 years ago)
Where Can I Buy A Swing Down Door Replacement For A Ge Nx-148e Lcd Keypad?
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
(Posted by btestrake 9 years ago)
Nx-1448e Battery
Power on panel is flashing. Manual says battery is low...WHERE IS BATTERY?
Power on panel is flashing. Manual says battery is low...WHERE IS BATTERY?
(Posted by gg 12 years ago)
'power' Is Flashing..manual States Power Is Low..where Is Battery?
(Posted by beckyhudson 13 years ago)