GE GFC325F Support Question
GE GFC325F Support Question
Find answers below for this question about GE GFC325F - 1/3 Horsepower Continuous Feed Disposer: Power Cord.Need a GE GFC325F manual? We have 1 online manual for this item!
Question posted by buhaDi on July 22nd, 2014
Where Is The Ge Garbage Disposal Gfc325f Reset Button?
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related GE GFC325F Manual Pages
Owners Manual - Page 1
...® Food Waste Disposer
ge.com
Safety Information
Connecting Electricity 2, 3 Safety Precautions 2
Installation Instructions
Attaching the Discharge Elbow 6 Components and Installation of Sink Flange 5 Connecting Disposer to Sink Flange 7 Dimensions/Typical Installations 8 Dishwasher Connection 6
Operating Instructions
Batch Feed Models 9 Care and Maintenance 10 Continuous Feed Models...
Owners Manual - Page 2
... to remove objects from the disposer.
c) Glass, china or plastic.
I To reduce the risk of this Owner's Manual.
Check with a Grounded Cord:
GROUNDING INSTRUCTIONS: This appliance ...Do not modify the plug provided with electrical power and procedures, call a qualified electrician. The plug must be followed, including the following into a disposer:
a) Clam or oyster shells.
g) Whole...
Owners Manual - Page 3
...
Remove Cover Plate
Bottom of electric shock. Use only UL approved ground clamp.
Red Reset Button
Ground Screw
A. If a plug-in length. Attach a power cord, minimum 18″ in length and not to the equipment-grounding terminal or lead on disposer. If BX cable is properly installed and grounded in the end bell for electric...
Owners Manual - Page 4
...; Cable connector • Flexible drain pipe • Power cord kit (Part Number PM3X215GDS)
4
Be sure to leave these instructions
for future reference. • Skill level - Disconnect electrical power supply to Consumer - Installation Instructions
Disposer
If you have questions, call 1-800-GECARES or visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions for...
Owners Manual - Page 5
...flush with the bottom edge of the sink opening.
Unscrew the support ring from the disposer by the factory. Some cast sinks will not move up , screw the
support ring ...
Groove Hopper
Dishwasher Discharge Inlet
Elbow Gasket
Disposer
End Bell (Electrical Connections)
Elbow Flange
Rating Label in This Area
*Not used with batch feed model
Screws
Discharge Elbow
INSTALLATION OF SINK FLANGE...
Owners Manual - Page 6
... may remove it or simply grind it up when the disposer is not to be connected, go on to a dishwasher, complete the following step.
... screwdriver or sharp instrument.
If the hose size is different, you will not damage the disposer in any way, but may take some time to the disposer.* Make sure all plumbing connections are connecting to "Attaching the Discharge Elbow" section.
1 ...
Owners Manual - Page 7
...Turn the mount ring about 1/4″ to the right so that the disposer is hard to turn, you may add a small amount of the mounting... jelly or liquid soap to the right until the disposer discharge elbow lines up tight. Installation Instructions 4 CONNECTING DISPOSER TO SINK FLANGE
1 ATTACH TO SINK FLANGE
Line up the disposer under the sink flange.
Locking Detail
Hopper Projection in...
Owners Manual - Page 8
...
183/16"
5 9/16"
4 1/2" 11/2"
GFB1060F Batch Feed Operation
SOME TYPICAL INSTALLATIONS
Direct replacement for most makes & models.
*9″ for model GFC320F, GFC520F, GFC325F, & GFC525F.
*10″ for models GFC530F, GFC535F, ... operation of the disposer that this dimension be 9″-12″, depending upon the models listed above, to avoid standing water in disposer motor housing.
*...
Owners Manual - Page 9
Continuous Feed Models
A. C. Do not be pushed down firmly to start the disposer. D. Remove the sink stopper and turn on a medium flow of cold water.
One of the disposer.
D. The stopper... of cold water. The disposer is actually increasing torque (grinding power) and is thoroughly flushed through
Small
the trap and drain. Before turning the disposer off . Cold water will...
Owners Manual - Page 10
... corrosion of cleaning or replacement. I If an odor develops, run orange or lemon rinds through the disposer. I Your disposer, except for the Batch Feed model, is equipped with a little household scouring powder will not grind and dispose such items as large bones, fibrous husks like lima bean pods and corn husks require considerable cutting...
Owners Manual - Page 11
... flange screws.
*Batch Feed does not include splash guard.
11
The reset button is at the top, it may have internal problems that require service or replacement. If the reset button has not been tripped, check for service... Then remove the object. ge.com
SAFETY NOTE: Before investigating, you must disconnect the power supply. disposer. If wiring and...
Owners Manual - Page 12
... or resetting of God.
If the product is located in an area where service by a GE Authorized Servicer is product repair as provided in the United States Louisville, KY 40225
Consumer Support
12
Printed in this Limited Warranty. Troubleshooting Tips Operating Instructions Installation Instructions Safety Instructions
Disposer Warranty. Staple your home. What GE Will...
Similar Questions
Where Is The Reset Button?
(Posted by laleiner 1 year ago)
Ge Gfc325f Disposal
My disposal was jammed, I unjammed it using a butter knife around the edges to remove the broken gla...
My disposal was jammed, I unjammed it using a butter knife around the edges to remove the broken gla...
(Posted by lemleyr70 5 years ago)
Ge Garbage Disposal Model Gfc525f Has Power But Will Not Grind
(Posted by lcurAncito 10 years ago)
Ge Gfc325f Garbage Disposal Runs Will Not Drain
(Posted by mlinwhi 10 years ago)
How Do I Remove Ge Garbage Disposal Gfc 530?
I tried to remove the disposal mounting ring with a flat screw driver, but it just does not turn. Ho...
I tried to remove the disposal mounting ring with a flat screw driver, but it just does not turn. Ho...
(Posted by nalindamani 11 years ago)