GE 24959 Support Question
GE 24959 Support Question
Find answers below for this question about GE 24959.Need a GE 24959 manual? We have 1 online manual for this item!
Question posted by Anonymous-98269 on February 10th, 2013
What Button Is 'select'???
The manual says to press and release 'SELECT' but there is no select button!?
Current Answers
Related GE 24959 Manual Pages
Instruction Manual - Page 1
24959
Universal Remote Instruction Manual
Instruction Manual - Page 2
Table of Contents
Introduction 3 Button Functions 4 Initial Setup 6
Battery Installation 6 Battery Saver 6 Code Saver 6 Code Setup 6 Direct Code Entry 7 Code Search 8 Code Identification Feature 9 Setup 10 Programming Combo Device Codes..10 DVD/DVR Punch-Through Feature ....10 Volume/Mute Control Feature 10 Setting All Volume/Mute Controls.......11 Setting Any Mode to...
Instruction Manual - Page 3
... equipment. Your new remote is a thing of the past! Use the original remote, if available, to your original equipment remote control! Sometimes buttons other than described in these instructions may not be used to use remote controls available today. For example, the CHAN and VOL buttons might be controlled by this GE Universal Remote Control. Introduction
Congratulations on...
Instruction Manual - Page 4
...controlling.
no
yes
4.
Also, this remote can only operate features that are referred to by different names on the device you might have functions that exist on the remote might need to record from your DVD/DVR. mute
list
input
last
DVR
9. Note: The REC button must be pressed twice to press REC button once, then press...15.
Some buttons on your product...
Instruction Manual - Page 5
..., cable box, etc.). 19. Red Indicator: Lights when any button is set to the previously selected channel or DVD repeat toggle. 20. MENU: Brings up your DVD/DVR even when the remote is pressed. 2. DVR: Press to setup learning functions. 28. Dot: used for digital channels, e.g., 2.3. (Controls ASPECT for some DVRs) +100: Used for setting up...
Instruction Manual - Page 6
... code tables (on the tab and lift the cover off if the buttons are changing batteries so that works for your product. Match the batteries to setup the remote.
Please refer to "Code Search" on page 8 for more than 30 seconds. Press the battery cover back into place. You can search through the...
Instruction Manual - Page 7
you can only store TV codes under the TV button.
1. Press and release the desired mode button (TV, DVD, etc.). Enter the 4 digit code from the code tables (on , then release the SETUP button.
2. For an invalid code, the red indicator flashes.
4. Note: If some buttons do not operate your equipment, try one of code under any...
Instruction Manual - Page 8
Manually turn on , then release the SETUP button.
3. Press the CHANNEL UP button repeatedly (up to store a Satellite code under that performs more functions.
If you want to 300 times) until the best code is not listed, try searching for Direct Code Entry and select CBL in Step 3 of Direct Code Entry. the MENU button might not work...
Instruction Manual - Page 9
... the red
indicator stays on. Repeat step 4 to find out what 4 digit code is the second digit. 6. Press and release the SETUP button. The red indicator blinks, then stays lit. 3. Code Identification Feature
Code Identification Feature
The Code Identification Feature allows you ...
Instruction Manual - Page 10
...release the SETUP button.
2. Press and hold SETUP until the red indicator turns off . Volume/Mute Control and PunchThrough Feature
Your remote allows you to the last DVD or VCR programmed mode you used, i.e., the transport buttons control.../Mute function or else VOLUME and MUTE will "punch-through to select which device mode controls VOLUME and MUTE.
If you hvae programmed a SAT/DVR or ...
Instruction Manual - Page 11
... the respective modes you have selected does not have Volume/Mute control.
5. Press and release MUTE; All other modes will not operate.
1. the indicator blinks, then stays on , then release SETUP.
2. Press and hold MUTE until the indicator remains on, then release SETUP.
2. Press and hold SETUP until the indicator blinks off , then release the button.
3. Note: The indicator will...
Instruction Manual - Page 12
... learn " features (such as RANDOM PLAY from your original CD remote control. Keep at least three feet away from a "Universal" remote, it might not be able to learn from incandescent or low-energy lights when learning. If you may be learned. a.
Only one Mode button e.g. e. Then carry out a Master Clear before learning and try...
Instruction Manual - Page 13
...remote DVD transport buttons unless you have learned all the required buttons for that button under the same Mode.
13 If problems reoccur with each other . k. some original DVD remotes include TV Volume/Mute button control...may need to approximately 1 inch and do not release the button being learned - Keep the distance between the two remotes to adjust the height of code. iii. does ...
Instruction Manual - Page 14
... will only transmit IR on the initial button press then stop. Press and hold any Original Remote button and move the Original Remote to exit at this procedure.
6. In these cases, quickly press and release the original remote button repeatedly during this point, press and release the SETUP button
14 You can now learn a button from your original remote's IR transmitter is where the two...
Instruction Manual - Page 15
... Learning is a learning problem, the indicator blinks for other by approximately 1 inch apart (see tips on .
3.
amp
aux
tv
aspect
learn .
8. Press and release the SETUP button when all desired remote commands are learned. Press and release the Learning Remote button that you want to learn
setup
no
yes
light
page
page
789
+100
enter
0
Line up your...
Instruction Manual - Page 16
...all modes
1. Release the SETUP button.
2. The red indicator turns off . Master Clear - All learned Commands under a mode
1. Release the SETUP button.
2. All Learned commands in the remote are now cleared. Press and release the LEARN button TWICE. Press and release the LEARN button TWICE. The red indicator blinks off.
4. Press and release the SETUP button. Press and release the SETUP...
Instruction Manual - Page 17
...the remote. (You might be
able to operate all features of your product
1.
Indicator blinks after installing new batteries.) 4. Lost Your Codes? Apply the sticker to control.
...remote is our website address which you should you lose your product.
This means the remote did not accept the code. 2.
Select the mode for future reference. Try to reprogram your product or the button...
Similar Questions
Ge 24959 Remote Codes
The instruction manual for this remote control does not have the specific codes to put in.it does te...
The instruction manual for this remote control does not have the specific codes to put in.it does te...
(Posted by jlefave33 9 years ago)
How To Change W Without The Remote Control
we lost the remote control to need to know if a General Electric universal remote work on Blu ray
we lost the remote control to need to know if a General Electric universal remote work on Blu ray
(Posted by georgehardin1982 9 years ago)
The Universal Remote Control Is Not Working
The problem is when I try to use it nothing works properly just the blue led lighting. What can I do...
The problem is when I try to use it nothing works properly just the blue led lighting. What can I do...
(Posted by nikcamel 11 years ago)
Need Code For A Panasonic Tv Using Ge 24993 Remote Control
Thanks
code for a Panasonic TV using GE universal remote control 24993 Thank you
code for a Panasonic TV using GE universal remote control 24993 Thank you
(Posted by luiscarloscalvocalvo 13 years ago)