2008 GMC Yukon Support Question
2008 GMC Yukon Support Question
Find answers below for this question about 2008 GMC Yukon.Need a 2008 GMC Yukon manual? We have 1 online manual for this item!
Question posted by Dthomascapecod on March 13th, 2013
Change The Headlights
how to remove the front bumper so that I can change the headlights
Current Answers
Answer #1: Posted by bengirlxD on March 13th, 2013 3:24 PM
bengirlxD
Member since:
November 5th, 2012 Points: 6,395,085
Member since:
November 5th, 2012 Points: 6,395,085
The bumper cover needs to be removed first which is usually attached with phillips type screws and are located underneath the bumper. Take out the screws. Then the bumber material underneath can be unbolted from behind the bumber, these bolts are torqued extremely tight so you may need to use a small pipe or breaker bar to get them loose. Then you will be to change your headlights.
Feel free to resubmit the question if you didn't find it useful.
Related Manual Pages
Owner's Manual - Page 2
For vehicles first sold , leave this manual in the vehicle.
We reserve the right to make changes after that may be available in this manual can be obtained from : GENERAL MOTORS, GM, the GM Emblem, GMC, the GMC Truck Emblem, and the ...
Owner's Manual - Page 94
... service procedures, and make sure the person performing work for you are close to or change your vehicle and the airbag system. There are probably part of the airbag system in ...serviced. Your dealer/retailer and the service manual have information about the vehicle that change
about servicing your vehicle's
frame, bumper system, height, front end or side sheet metal, they may keep the ...
Owner's Manual - Page 122
... including interference that matches a decoder in the key that may cause undesired operation. Changes or modifications to this equipment. When the PASS-Key® III+ ...has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III+ is removed from the ignition. Turn the ignition off and try again.
2-24 PASS-Key® III+ uses a ...
Owner's Manual - Page 197
... vent and floor outlets depending upon where the knob is placed between the settings. To remove the front ashtray pull the ashtray up. To use the cigarette lighter, push it in the ashtray.
To change the current mode, select one of the following:
H (Vent):
This mode directs air to the instrument...
Owner's Manual - Page 253
... the unlock button on matching transmitters to access the settings for this feature. NO CHANGE: No change will move back when the key is displayed on the DIC. To select a ... the set /reset button while the desired setting is removed from the ignition. ON: The driver's seat will be made to this feature. NO CHANGE: No change will occur. The current setting will automatically move ....
Owner's Manual - Page 291
.... See your warranty. To adjust the volume on the headphones, use . Battery Replacement
To change the batteries on the right side. Make sure that they are to the headphones become worn or...located on the inside of the headphones. The headphones automatically turn off after four hours of time, remove the batteries and keep them in a cool, dry place.
3-117 The symbol R (Right) appears...
Owner's Manual - Page 292
...enter) button to use the auxiliary inputs of the connected auxiliary device by the radio system. How to Change the RSE Video Screen Settings
The A/V jacks, located on the remote control switches the video screen from ... device to the RSE system. See Radio(s) (MP3) on screen setup menu. Refer to remove the setup menu from an auxiliary device such as a camcorder or a video game unit to...
Owner's Manual - Page 297
... two batteries in the setup menu by pressing the display menu button on to play from the beginning of time, remove the batteries and keep them in ACC/ACCESSORY. If the remote control is no obstruction between the remote control and... resumes off and sometimes at both sides or it looks stretched out.
Battery Replacement
To change the remote control batteries, do the following: 1.
Owner's Manual - Page 370
... Quality Grading ...5-83 Wheel Alignment and Tire Balance ...5-84 Wheel Replacement ...5-85 Tire Chains ...5-86 If a Tire Goes Flat ...5-87 Changing a Flat Tire ...5-88 Removing the Spare Tire and Tools ...5-90 Removing the Flat Tire and Installing the Spare Tire ...5-94 Secondary Latch System ...5-100 Storing a Flat or Spare Tire and Tools ...5-104...
Owner's Manual - Page 388
...a restriction indicator, you should inspect the air filter restriction indicator at each engine oil change after each 50,000 mile (80 000 km) interval. See Engine Compartment Overview on page 6-4... the filter at every oil change " zone, replace the filter and reset the indicator. When you have the engine air cleaner/filter removed, lightly shake it to be replaced....
Owner's Manual - Page 447
In an emergency, you change a wheel, remove any rust or dirt from places where the wheel attaches to do this; but be sure to use a scraper or... or dirt off and cause an accident. After the tires have been rotated, adjust the front and rear in the tire rotation. See Changing a Flat Tire on page 5-75.
5-79 Push, pull, and then try to get all wheel nuts are properly tightened. See "...
Owner's Manual - Page 453
...sensors, replace them only with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. Your...except some aluminum wheels, which you need. Each new wheel should be dangerous. See Changing a Flat Tire on your tires lose air and make your vehicle can also cause ...
Owner's Manual - Page 458
... and the wheel block retainer by turning it counterclockwise. 3. Removing the Spare Tire and Tools
The equipment you will need to change a flat tire is stored under the storage tray, which is located on the finger depression under the jack symbol. 4. Remove the wing nut (B) used to retain the tool bag...
Owner's Manual - Page 462
Do a safety check before proceeding. See Changing a Flat Tire on the wheel and gently pry the cap out.
5-94 Put the spare tire near the flat tire and ... the retainer and pull it through the center of the wheel wrench in the slot on page 5-88 for more information.
Remove the center cap, if your vehicle has one, by placing the chisel end of the wheel along with the cable and latch...
Owner's Manual - Page 466
CAUTION:
(Continued)
places where the wheel attaches to do this; Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel.
{...5.
Take off and cause an accident. In an emergency, you change a wheel, remove any rust or dirt from CAUTION: (Continued)
5-98 Remove all the rust or dirt off. See Changing a Flat Tire on the parts to which it is fastened, ...
Owner's Manual - Page 471
... cable, insert the hoist end of extension, and wheel wrench into the hoist shaft hole in the bumper clockwise to lower the spare the rest of you as you pull the jack out from under the ...you can. Tilt the tire retainer at tire, see Removing the Flat Tire and Installing the Spare Tire on either side of the way. 14. To continue changing the flat the end of the cable and ...
Owner's Manual - Page 478
...because they can alter the appearance by increasing the gloss in gloss may permanently change the appearance and feel of your instrument panel. The increase in a non...
A soft cloth dampened with water may be used to dry naturally. Allow the leather to gently remove dust and dirt. If any impression that are not recommended. After the cleaning process has been completed...
Owner's Manual - Page 523
... A separate booklet entitled "Warranty and Owner Assistance Information" furnished with the Bumper to make any changes or discontinue the Roadside Assistance program at any time without notification...violation of local, Municipal, State, Provincial, or Federal law, and mounting, dismounting or changing of or included in the coverage provided by the New Vehicle Limited Warranty. If it ...
Owner's Manual - Page 544
... Flat Tire ...5-94
12 Sheet Metal Damage ...5-114 Shifting Into Park (P) ...2-44 Shifting Out of Park (P) ...2-46 Signals, Turn and Lane-Change ...3-8 Snow Plow ...4-41 Spare Tire ...5-107 Installing ...5-94 Removing ...5-90 Storing ...5-103 Specifications, Capacities ...5-124 Speedometer ...3-39 Split Bench Seat (60/40) ...1-12 StabiliTrak® System ...4-6 StabiliTrak®...
Owner's Manual - Page 545
Tires (cont.) Removing the Spare Tire and Tools ...5-90 Secondary Latch System ...5-100 Spare Tire ...5-... Recommendations ...4-63 Transmission Fluid, Automatic ...5-22, 5-24 Transmission Operation, Automatic ...2-31 Trip Odometer ...3-39 Turn and Lane-Change Signals ...3-8 Turn Signal/Multifunction Lever ...3-7
U
Ultrasonic Rear Parking Assist (URPA) ...2-58 Uniform Tire Quality Grading ...5-83 ...
Similar Questions
94 Yukon 5.7 Having Issues Changing Rear Brakes, Emergency Cable Does'nt Seem To
changing rear brakes, something's wrong, emergency cable when engaged only pulls a lil slack but not...
changing rear brakes, something's wrong, emergency cable when engaged only pulls a lil slack but not...
(Posted by ve6bmw 9 years ago)
2008 Gmc Yukon Denali Front Bumper Cover
What are the steps for removing the fron bumper cover on the 2008 GMC Yukon Denali?
What are the steps for removing the fron bumper cover on the 2008 GMC Yukon Denali?
(Posted by flanger 10 years ago)
Change Engine Oil, We Already Changed The Oil. And The Light Is Still On
(Posted by rosarojas20 11 years ago)
How To Adjust Low Beam Headlights On A 2002 Yukon Denali
(Posted by bdgrkegonsa 11 years ago)