Frigidaire GLEQ2152ES Support Question
Frigidaire GLEQ2152ES Support Question
Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!
Question posted by ricthet on January 11th, 2011
How Do U Get The Front Off To Replace The Plastic Drum Guides
one of the front plastic drum guides guides broke
Current Answers
Related Frigidaire GLEQ2152ES Manual Pages
Use and Care Manual - Page 2
... reach your appliance. Model Number This Use and Care Guide provides general operating
instructions for the recycling of electrical and electronic equipment. It also contains information about :
...valuable information about features for this product, please contact your local city office, your dryer. Instead
it in personal injury, property damage or damage to prevent property damage,...
Use and Care Manual - Page 3
...electrical power cord. Do not use of children is necessary when the dryer is unpacked. Note: The instructions appearing in this Use and Care Guide are not meant to cover every possible condition and situation that could result in your dryer has a drying rack, always replace... plastic sheets can become airtight chambers. • Keep laundry products out of children's reach.
Items contaminated...
Use and Care Manual - Page 4
... the risk of fire, electrical shock, or injury to comply with small and medium sized items.
• For delicate or very small loads, add 2 lint-free towels for the installer's reference. Load the dryer.
• The average load will stop before operating this Owner's
Guide. The dryer
will fill the drum 1/3 to resume the cycle...
Use and Care Manual - Page 5
...electrical shock could enter the exhaust system and cause damage to illuminate the dryer drum during loading and unloading.
A clothes dryer produces combustible lint. Dry thoroughly and replace.... the dryer interior, unplug the electrical power cord to persons or property, comply with a reversible door. Place items to the INSTALLATION INSTRUCTIONS for items containing plastic, foam...
Use and Care Manual - Page 6
... fabric softener in place.
Care and Cleaning con't
Do not store or place laundry products on top of dryer at medium or low heat for 5-10 minutes.
• Remove items immediately.... to fabric.)
• Pilling is clean and in washer or dryer to
electricity.
• Or, add a fabric softener sheet and
reduce static electricity.
• Lint screen not clean
tumble without heat.
•...
Use and Care Manual - Page 7
... electrical line is not overloaded and the dryer is empty or there has been a utility interruption of defective workmanship or materials in the dryer circuit. Gas supply valve is blown, the drum may save both time and expense. See INSTALLATION INSTRUCTIONS.
High humidity.
See Drying Procedures. OCCURRENCE
Dryer does not start. Reset circuit breaker or replace...
Use and Care Manual - Page 8
...REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. Products used in accordance with original serial numbers that has been ... other than genuine Electrolux parts or parts obtained from its original owner to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, ...
Technical Data Sheet - Page 1
...dryer. If reading is not 50 K (± 10%), replace thermistor. If good, replace electronic control. If reading is not 50 K (± 10%), replace thermistor. If good, replace electronic control. If meter reads 240V on electric..., air leaks around air duct, broken blower fan blades, worn or loose drum seals, dryer installed in closet with solid door, or bad connection in a period of ...
Installation Instructions - Page 2
... lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers.
Plastic knife.
minimum time delay fuses or circuit breakers. Individual 15 amp.
NOTE: Do not under any electrical switch; See ELECTRICAL CONNECTIONS for Installation: 1. PRE-INSTALLATION REQUIREMENTS
Tools and Materials Required for additional instructions. Carpenter's level...
Installation Instructions - Page 3
...4
MAXIMUM LENGTH of plastic duct or metal foil duct, replace it must be a minimum of your present system is not exhausted outdoors, some fine lint will increase dryer times. If your dryer. Lint can become ...Restricted air flow will be exhausted into the laundry area. Ensure the present duct is less than 0.75 inches of the dwelling! The dryer MUST NOT be expelled into a chimney, ...
Installation Instructions - Page 4
... codes, or in the
same closet as the Gas dryer. 3.
However, on electric dryers, exhausting can be used.
2. The more the dryer is used, the more often you should check the ...restriction. • Running the exhaust system through your dryer to be unobstructed when a door is not plastic-coated. Stainless steel or plastic-coated brass MUST be accomplished by installing Exhaust Kit, ...
Installation Instructions - Page 6
... (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to clear...
Installation Instructions - Page 7
... area beneath the mobile home is designed so the door swing may need a plastic knife to scratch the paint.
2. Open the dryer door. CAN/CSA C22.2 (latest editions) for other important venting requirements.
...NOTE: You may be 4 inches (10.16 cm) in the open screw holes on each of the dryer exhaust outlet.
4. Install the four hinge hole plugs in diameter with the four screws.
4. MOBILE HOME...
Installation Instructions - Page 8
...from door. 6. Remove the two hinges and reinstall the four screws. NOTE:
You may need a plastic knife to help remove the plugs. Apply moderate downward pressure on the lens with the handle holes ... to reinstall the hinges. 11. NOTE: You may need a plastic knife to avoid scratching the paint. 5. Be careful to the dryer front panel. Install the plugs from Step 1 into the holes...
Installation Instructions - Page 9
...-grounding conductor and a grounding plug, the plug MUST be connected to the pre-installation requirements in this manual for proper grounding.
2. GROUNDING REQUIREMENTS
ELECTRIC Dryer
Improper connection of electrical shock. The dryer MUST be plugged into a properly grounded three-prong receptacle. Refer to a grounded metal,
permanent wiring system; If the strain relief is properly...
Installation Instructions - Page 10
...RED
BLACK TIGHTEN
NUT
WHITE
TO THESE THREADS
NUT
STRAIN RELIEF MOUNTING BRACKET
STRAIN RELIEF MOUNTING B R A C K E T POWER CORD
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM
ELECTRIC Dryer
1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the terminal block. Remove...
Installation Instructions - Page 11
... and situation that is off . REPLACEMENT PARTS
If replacements parts are not meant to seal all other flammable vapors. Apply an approved thread sealer that may occur. Open the shutoff valve in your Use and Care Guide before calling for the gas line to light.
6. NOTE: On gas dryers, before the burner will shut...
Operating Instructions - Page 1
...through heated air.
PN 134431300A (0501)
Operating Steps
Read "Drying Procedures" in your dryer Owner's Guide before operating this appliance. Check that cycle is selected. This helps reduce wrinkling and...hang or fold.
9.
Auto Dry cycles take the guesswork out of ventillation system, electrical voltage or gas pressure can also affect drying time. The load will continue to Towels...
Operating Instructions - Page 2
...
Timed Dry is started.
Cycle Adjustments
A suitable combination of the cycle. See the "Dryer Settings Chart" for wrinkle free, permanent press and lightweight fabrics. Medium heat is selected.... fabric care label instructions on items to dry items containing feathers or down , foam rubber, plastics or rubber-like materials.
To avoid fire hazard, do not use heat to be used with...
Operating Instructions - Page 3
...Guide for assistance.
PN 134431300A (0501)
Press buttons lightly and release.
Dryer overloaded. Consult the Error Code Chart below or the "Avoid Service Checklist" in the control panel. If the dryer...sheet residue Clean out ventilation system. Error Code 4 beeps / E4A
Error Dryer ran too long
6 beeps / E68
Push button does not function
Possible Causes Lint filter blocked. ERROR...
Similar Questions
Trouble Restarting Electric Dryer
After an electric dryer warms it will not restart unless the selector nob is tapped. Which part need...
After an electric dryer warms it will not restart unless the selector nob is tapped. Which part need...
(Posted by jrpetrick 5 years ago)
Replaced My Circuit Board On Dryer The Timer Doesn't Have The Right Minutes For
I replaced the circuit board in my dryer the selector dial is off from the timer minutes. Do Iave to...
I replaced the circuit board in my dryer the selector dial is off from the timer minutes. Do Iave to...
(Posted by cynthiadelahoussaye 9 years ago)
Give Me A Diagran Of Where Is The Fuse Locatedin A Frigidaire Electric Dryer
(Posted by 101robi 9 years ago)
How To Replace Belt For Gleq2152es0 Frigidaire Electric Dryer
(Posted by HBChodian 10 years ago)
Frigidaire Electric Dryer Fer641fs. No Heat. Timer Not Advancing.
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
(Posted by mouatech 10 years ago)