Frigidaire FRG5711KW Support Question
Frigidaire FRG5711KW Support Question
Find answers below for this question about Frigidaire FRG5711KW.Need a Frigidaire FRG5711KW manual? We have 5 online manuals for this item!
Current Answers
Answer #1: Posted by Odin on March 24th, 2015 8:50 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
For a list of this model's available parts (which you can order from the same site), with part numbers, pictures, and prices, see http://www.repairclinic.com/Shop-For-Parts/a8b2d702042/Model-FRG5711KW0-Frigidaire-Dryer-Parts.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Frigidaire FRG5711KW Manual Pages
Installation Instructions (All Languages) - Page 2
...appliance. • Do not touch any appliance.
Pre-Installation Requirements
Tools and materials needed for HOME USE only. Flexible venting materials are labeled with a WARNING or CAUTION... on the risk type as restaurants, beauty salons, etc. • Do not install a clothes dryer with flexible plastic venting material. CAN/CSA C22.2 No. 112 (latest editions) for installation...
Installation Instructions (All Languages) - Page 3
...)
4-WIRE POWER SUPPLY CORD KIT (not supplied)
4-wire receptacle (NEMA type 14-30R)
The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 type SRDT rated at 240 volt AC ...volt AC minimum, 30 amp, with 3 open end spade lug connectors with clothes dryers.
OUTLET RECEPTACLE - The dryer is equipped with power created by gas powered generators, solar powered generators, wind powered...
Installation Instructions (All Languages) - Page 4
... replace it with flexible plastic or metal foil venting materials. FIRE HAZARD - If your dryer to collapse, be 1/2 inch (1.27 cm) pipe.
3.
Correct Correct
Incorrect Incorrect
4 The ...causing gas leaks. These conditions will corrode when subjected to the dryer.
6.
EXPLOSION HAZARD - The dryer MUST be installed immediately upstream of the gas supply piping system ...
Installation Instructions (All Languages) - Page 5
...which can become caught in the surrounding area.
- MAXIMUM LENGTH of 4" (10.2cm) Rigid Metal Duct
VENT HOOD TYPE (Preferred)
Number of air.
4" (10.2cm)
louvered
2.5" (6.35cm)
0
60 ft. (18.3 m)
48 ft. (14.6 m)
1
52... venting, do not exceed 8 ft. (2.4 m) duct length. Do not exhaust dryer into the laundry area. An accumulation of lint in any concealed space of a building. Plugging the...
Installation Instructions (All Languages) - Page 6
...11 cm)
5 7/8" (15 cm)
3 3/4" (9.5 cm)
13 1/2" (34 cm)
Manufactured or mobile home installation
1. Dryer MUST be exhausted outside make up for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSAZ240 ...Part 32-80 (formerly the Federal Standard for rear exhausting. On gas dryers, exhausting can be accomplished by installing Exhaust Kit, P/N 131456800, available...
Installation Instructions (All Languages) - Page 7
...dryer needs the space around it for the full length of combustion and ventilation air. 3. Openings are kept or stored. In an area exposed to do so can result in the same closet as the gas dryer...cm) 1" (2.5 cm)
*For under-counter installation, top panel must be removed and kit number 131629100 must be solid with curtains,
drapes, or anything that will come in a bedroom, bathroom...
Installation Instructions (All Languages) - Page 8
... safe electrical installation of the cord, resulting in the cord. Locate the dryer within reach of the receptacle for the length power cord to be properly grounded. Refer to ...manual for the proper power cord to be installed onto pow- Follow the instructions in this dryer utilizes and can cause electrical shorts. er cord. A chemical reaction occurs between copper and aluminum...
Installation Instructions (All Languages) - Page 9
... receptacle
Do not, under any circumstances, cut, remove, or bypass the grounding prong.
Electric dryer (USA)
- Improper connection of electrical shock. Check with a licensed electrician if you are...as to a grounded metal, permanent wiring system; For a grounded, cord-connected dryer:
1. The dryer MUST be plugged directly into an appropriate, copper wired receptacle that matches you ...
Installation Instructions (All Languages) - Page 10
... two power cord outer conductors to the outer, BRASS colored terminals on the back of the dryer.
conversion kit must be loosely in the
upper corner on all connections by a qualifi... Neutral (center wire)
Neutral terminal
7. Apply an approved thread sealer that allows ease of the dryer. Tighten the screw securely. 6. Tighten both screws securely.
- Do not make a sharp bend ...
Installation Instructions (All Languages) - Page 11
...Be sure the power is off power supply to the center, SILVER colored terminal on top of the dryer.
3.
Install a UL-approved strain relief according to the outside exhaust system (see pages 4 through ...the strain relief.
5. Failure to neutral (silver) terminal for service. 7. Move the internal dryer harness ground (WHITE) wire to the terminal block and attach it along with the neutral (...
Installation Instructions (All Languages) - Page 12
...LP CONVERSION KIT
P/N PCK2003 Gas dryers intended for this dryer may be reversed at any time without additional parts.
Replacement parts:
If replacements parts are needed for your dryer, contact the source where you... kit number 131629100 must use of the door opening.
Rotate the door 180° and reinstall the door hinges to the dryer front panel (see below). Open the dryer door....
Complete Owner's Guide (English) - Page 2
... checklist 8 Warranty 9 Français 10 Español 19
Product Record
Read and Save These Instructions
Record Your Model and Serial Numbers The model and serial numbers of your dryer are soot and carbon monoxide, both of which may be produced by a qualified installer, service agency or the gas supplier...
Complete Owner's Guide (English) - Page 3
... children's reach.
You can become airtight chambers.
• Keep laundry products out of a gas dryer must be plugged into , on or near dryer at any circumstances, cut, remove, or bypass the grounding prong... them for the installer's reference. Do not stack or place laundry or throw rugs against the front or back of the dryer.
• Do not spray any accumulation of lint around the...
Complete Owner's Guide (English) - Page 4
... switch automatically turns off the motor in electrical shock or injury.
• Do not use any type spray cleanser when cleaning dryer interior. Failure to tumble freely for drying. Items need room to do not reach into the drum. every load.
4
Repeat
stain removal process and wash again before operating your speci...
Complete Owner's Guide (English) - Page 5
...set the cycle selector on the indicator line to the wrinkle release
setting and press start dryer. It is determined automatically at the temperature selection of your choice. • Casual-medium.... Energy Saving Tips
• Keep the lint screen clean and exhaust the dryer correctly. • Sort laundry properly and select proper temperature and
cycle settings. AUTO DRY DAMP DRY This ...
Complete Owner's Guide (English) - Page 6
... under the lip of the door opening.
The filter is not in the Important Safety Instructions and those listed below.
• Before cleaning the dryer interior, unplug the electrical power cord to the Installation Instructions supplied with warm, soapy water. Regularly inspect the outdoor exhaust opening . Hazardous fumes or electrical...
Complete Owner's Guide (English) - Page 7
... Reduce load size and rewash using liquid fabric softener in dryer after
cycle ends. Do not store or place laundry products on top of dryer at to small loads for 5-10 minutes.
• ... When ironing, use a window cleaner with ammonia or mild soap and water.
• Before moving the dryer, place a strip of cardboard or thin fiberboard under the front leveling legs to prevent damage to ...
Complete Owner's Guide (English) - Page 8
... of items.
See "Operating Instructions." The list includes common occurrences that are 2 house fuses in dryer too long. Drying cycle takes too long, outside of rigid or semi-rigid metal. Lint fi...; bends and must have enough air supply to a 208 volt circuit. Items left in the dryer circuit.
LP gas supply tank is empty or there has been a utility interruption of the drum...
Complete Owner's Guide (English) - Page 9
...Expenses for making the appliance accessible for appliances not in a commercial setting.
7. If You Need Service
Keep your receipt, delivery slip, or some other than in materials or workmanship, or ...covered by this warranty must be performed by contacting Electrolux at the addresses or phone numbers below. Service under this warranty. Service calls to change or add to any parts...
Similar Questions
Hi I Need A Light Bulb For My Dryer Aeq6700fs What Size And Kind Do I Need?
(Posted by nak857 1 year ago)
Need To Fix Ed68 Code On My Model Gleq2152ee0 Front Load Dryer
need to fix e68 code on my model GLEQ2152EE0 FRONT LOAD DRYER
need to fix e68 code on my model GLEQ2152EE0 FRONT LOAD DRYER
(Posted by Ledesma2020 3 years ago)
Dryer Makes Squeaking And Scraping Noises I'm Assuming It Needs Guides.
Can you tell me the part #s of the parts I need to repair it?I see there are kits available on line ...
Can you tell me the part #s of the parts I need to repair it?I see there are kits available on line ...
(Posted by Jblb007 10 years ago)
Dryer Doesn't Get Hot, Do I Need To Make Service Call
dryer doesn't get hot, do i need to make a service call or is there a reset button
dryer doesn't get hot, do i need to make a service call or is there a reset button
(Posted by bellemidwest 13 years ago)