Frigidaire FEQ1442ES Support Question
Frigidaire FEQ1442ES Support Question
Find answers below for this question about Frigidaire FEQ1442ES - 27" Electric Dryer.Need a Frigidaire FEQ1442ES manual? We have 2 online manuals for this item!
Question posted by Anonymous-171631 on June 20th, 2022
Where Is The Moisture Sensor Located
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on June 20th, 2022 8:02 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,604,800
Member since:
May 9th, 2021 Points: 16,604,800
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Frigidaire FEQ1442ES Manual Pages
Installation Instructions - Page 2
...27 m)
14 ft. (4.27 m)
10 ft. (3.05 m)
NOT RECOMMENDED
Individual 30 amp. POWER SUPPLY CORD KIT -
See ELECTRICAL CONNECTIONS for Installation: 1.
Do not use with a 120 volt 3-wire power cord.
Individual 15 amp. The dryer...replace it must be expelled into the laundry area. Carpenter's level. 4. Ensure ... located so the power supply cord is accessible when the dryer is...
Installation Instructions - Page 3
..., accessible for proper operation. Read the measurement on electric dryers, exhausting can be exhausted outdoors.
5. If the system back pressure is unacceptable. The dryer MUST be to the right or left side of the cabinet or the bottom of the dryer. LOCATION OF YOUR DRYER
DO NOT INSTALL YOUR DRYER:
1. In an area exposed to or less...
Installation Instructions - Page 4
... to clear knobs (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to...
Installation Instructions - Page 5
.... Remove the four hinge hole plugs from the left side and remove the foam shipping base. Dryer MUST be 4 inches (10.16 cm) in the open screw holes on its left side of the...the four hinge hole plugs in diameter with the termination securely fastened to the dryer front panel (see below). Return the dryer to scratch the paint.
2. Conversion is enclosed, the exhaust system MUST terminate ...
Installation Instructions - Page 6
...handle by removing the handle screws in Step 4. 7. Install the plugs from turning. Open the dryer door. Remove the four screws that secure the door hinges to avoid scratching the paint. 5.... NOTE:
You may need a plastic knife to keep it 180°. Be careful to the dryer front panel.
Retain the plugs for use later. Apply moderate downward pressure on a flat surface ...
Installation Instructions - Page 7
... WIRE
RED
BLACK
WHITE
NUT
STRAIN RELIEF MOUNTING BRACKET
TIGHTEN NUT TO THESE THREADS
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the appliance. Remove the ground wire from this plug.
Finger tighten the nut only...
Installation Instructions - Page 8
... other flammable vapors. Place all wires prior to ensure the power is located inside the dryer console or under the top panel.
conversion kit must be applied when ...clothing, etc.) obstructs the flow of the dryer. Wiring errors can become airtight chambers causing suffocation. If this washer may occur.
Connect a 1/2 inch (1.27 cm) I.D. NLPWD15, specifically designed for this...
Operating Instructions - Page 1
..., turn the TEMP knob to handle during Press Saver when the Cycle Signal option is not available for best drying results.
The dryer senses the moisture level of installation and electrical voltage or gas pressure can also affect drying time. A suitable dryness level and options will not light.
6. Room temperature and humidity, type...
Operating Instructions - Page 2
... in any Auto Dry cycle will result in crowded closets or drawers, or unpacked from the dryer at the end of dryness level and options will automatically be remembered each cycle. To avoid...to dust draperies.
If a dryness level or option is recommended for delicate fabrics. See the "Dryer Settings Chart" for most loads.
The cycle must be paused before the cycle is recommended for...
Operating Instructions - Page 3
... Dry Cycle Only
*
*
*
*
*** Estimated cycle duration is based on normal
dryness level and factory settings. Make correction, then select a cycle and press START. If the dryer stops, status lights flash again and the beeping continues, please contact service for the possible cause and solution. Disengage button. Press buttons lightly and release...
Similar Questions
Dryer Lights On Randomly
Dryer lights come on randomly. Push cancel and they go off. Sometimes minutes later it comes on agai...
Dryer lights come on randomly. Push cancel and they go off. Sometimes minutes later it comes on agai...
(Posted by Howell04 2 years ago)
Dryer Stops With The Control And Lock Flashing, And The Load Is Still Damp.
Why does the dryer stops with the control and lock flashing, and the load is still damp.
Why does the dryer stops with the control and lock flashing, and the load is still damp.
(Posted by RicksEmailDrop 7 years ago)
Dryer Stops And Beeps 6 Times
The dryer stops and beeps 6 times, lights flash and does not reset.Cleaned out the lint, front and b...
The dryer stops and beeps 6 times, lights flash and does not reset.Cleaned out the lint, front and b...
(Posted by electqa2002 8 years ago)
Electric Dryer Conversion To Gas?
Can my dryer be converted to gas ?
Can my dryer be converted to gas ?
(Posted by Anonymous-155161 8 years ago)
Frigidaire Electric Dryer Fer641fs. No Heat. Timer Not Advancing.
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
My electric dryer has no heat and the timer is not advancing like it suppose to. It just keeps spinn...
(Posted by mouatech 10 years ago)