1996 Ford Explorer Support Question
1996 Ford Explorer Support Question
Find answers below for this question about 1996 Ford Explorer.Need a 1996 Ford Explorer manual? We have 2 online manuals for this item!
Question posted by niArt on September 30th, 2013
95 Explorer Lock Cylinder Won't Turn To Acc Position
The person who posted this question about this Ford automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Manual Pages
Owner's Manual - Page 13
... lap/shoulder belts
NOTE: Be sure to the position that the shoulder portion of 5 mph (8 km/h) or more, the lap/shoulder belt locks and helps reduce your forward movement. Pull the combination... lap/shoulder belt from the retractor so that suits you brake hard, turn hard, or if your vehicle ...
Owner's Manual - Page 69
... the gearshift is securely latched in P (Park) (automatic transmission) or in the ignition lock cylinder. RWARNING Turn the key to LOCK whenever you to operate while the engine is not running . Starting Your Explorer
Ignition
Understanding the Positions of the Ignition
The positions of your vehicle unattended while it is running .
Never leave your vehicle's electrical accessories...
Owner's Manual - Page 70
...brake. (This will vary, depending on the type of the steering column, just above the key lock cylinder. If you have a manual transmission, you have a key release lever which allows you do not ...Ignition
Procedures for removing your vehicle's gearshift lever is in this position while the engine runs.
The key returns to the ON position once the engine is on a grade.) 68 START cranks the...
Owner's Manual - Page 71
... the gearshift is mounted on hot, sunny days, temperatures in the key release button. 5. Starting Your Explorer
3. Turn the key to OFF. 3. Remove the key. Further, on the floor:
1. Remove the key. Turn the ignition key to LOCK. 6. Push and hold in a closed vehicle could accidentally injure themselves or others through inadvertent operation of...
Owner's Manual - Page 73
...do not flood the engine, then try again. Turn the ignition key to the ON position after the engine has started. Allow the key to return to the ON position. 3. s At temperatures above 10˚F (-... have difficulty in turning the key, rotate the steering wheel slightly because it may be binding. Starting Your Explorer
Before you start in fifteen (15) seconds on the first try, turn the key to ...
Owner's Manual - Page 77
Turn the ignition key ON for fuel pump shut-off switch
75 Check under the vehicle for leaking fuel. If you ...not see or smell fuel, you see or smell fuel, push the red reset button
down. Starting Your Explorer
If your vehicle. Reset button for a few seconds, then turn it
OFF.
5. Check all vehicle warning lights before driving your engine cranks but does not start your vehicle...
Owner's Manual - Page 82
... serviced. The following warning lights and gauges are optional. If the fluid level is low in the master cylinder reservoir. If the light stays on or comes on when you to verify that the brakes may not be...light symbols
81 Some of the warning lights and gauges alert you turn the ignition key to START to possible problems with your dealer or a qualified service technician.
Owner's Manual - Page 83
... safety belt is buckled before the key is turned to 8 seconds. Anti-lock warning light symbol
RWARNING If the anti-lock brake system warning light remains on or comes on for 60 seconds and the chime sounds for 4 to the ON
position, both the light and chime turn off. s If the safety belt is buckled...
Owner's Manual - Page 136
... ignition key must be turned to the interval operation you desire.
136 Interval wiper on turn signal lever
To set the interval wipers, rotate the knob at the end of the turn on steering column
Windshield Wipers and Washer
To turn signal lever toward or away from the instrument panel to the ON or ACC position.
Owner's Manual - Page 150
...be opened from falling out. RWARNING When driving your vehicle. You can lock the liftgate by using the power door lock switch on the left side of the cargo area. To open the ... and to the liftgate door lift cylinders and attaching hardware. Liftgate Handle and Locks
Liftgate handle and locks
You can unlock the liftgate by using the key, pushing the lock button down, or using the key...
Owner's Manual - Page 156
... driver's side. For your convenience, we have duplicated this entry system, the illuminated entry system turns on the interior lights for 25 seconds and the buttons on your owner's wallet card found in... system, you use this code in the glove compartment s taped to the computer module
When you can lock or unlock the vehicle doors without using a key. The code is:
s on the keypad light up...
Owner's Manual - Page 162
... was triggered. 162 Arming and Disarming the Alarm System with the remote entry LOCK button or by turning the ignition to the ON or ACCESSORY position. If a door, liftgate or the liftgate window is open . When you that a door or the liftgate is pressed on the vehicle's interior lights for approximately 2 ...
Owner's Manual - Page 166
... them on with the dimmer thumbwheel or if any door is turned off, the vehicle will not turn off battery voltage to all at the same time. You will automatically turn off if you should take all your dealer to the RUN or ACC position. The system will need to take your vehicle's transmitters to...
Owner's Manual - Page 168
...system is armed, the THEFT indicator will begin a 30 second countdown to confirm the doors are locked, two short horn chirps will begin to the ON or ACC position.
Remember, all doors, the liftgate and liftgate window must be assured that the anti-theft ...disarm the
anti-theft system only when the anti-theft alarm is triggered or disarmed. s Turn ignition to flash with a key.
Owner's Manual - Page 172
... without holding down the window switch. The driver's door has a master control switch that position.
172 Lift the latch and pull inward, then press latch outward to use your power... is pressed while the window is going down position for less than 1/2 second, then release it. You must place the ignition switch in the ON or ACC position to lock the levers.
To close, depress the levers ...
Owner's Manual - Page 184
...adjustment lever of the seat. The power controls on the driver's seat
To adjust the infinite position seatback, pull up on the handle while leaning against the back of an unoccupied seat will ...allow the seatback to fold forward for access to lock the seat in the desired position, depress the "SET"
button, then press the "1" button within 5 seconds or until...
Owner's Manual - Page 206
Turn the "D" rings counterclockwise to the desired positions and lock into place by hand. The "D" rings should be properly secured to the luggage rack to ... rack has two "D" rings (one on the roadway.
206 The rear rack can be completely removed in the "UNLOCKED" position by sliding the crossbar toward the rear of the vehicle until it becomes free of the luggage rack guide rails) that can...
Owner's Manual - Page 267
...brake is fully released, but you leave your vehicle may not be adversely affected. Turn the key to LOCK whenever you can use the gearshift in 1 (First) (manual transmission). Lift your...characteristics.
267 Use care until you pull the parking brake release lever. Driving Your Explorer
RWARNING When parking, do not take these precautions, your vehicle. Driving Under Special ...
Owner's Manual - Page 360
... moving the wipers across the windshield may need to the ACC position and turn your blades. Cycle windshield wiper arm and wiper blade to clean your wiper blades. To remove wiper blade assembly from wiper mounting arm,
depress lock tab and push wiper mounting arm away from wiper blade assembly.
3. Use undiluted windshield washer...
Owner's Manual - Page 379
Servicing Your Explorer
Brake master cylinder
Power Steering Fluid
Check the level of the NORMAL operating temperature range.
2. Check the fluid level on the side of the dipstick, opposite the side marked FULL COLD. Make sure that the cap assembly is highlighted in
yellow in your vehicle). While the engine idles, turn the steering...
Similar Questions
Ignition Lock Cylinder Issue
My 96'ford explorer 2wd v8 stop working. .. I tried to start it , but the key just kept spinning. .....
My 96'ford explorer 2wd v8 stop working. .. I tried to start it , but the key just kept spinning. .....
(Posted by wwwderrickwoodall 10 years ago)
2012 Ford Explorer, Auxiliary Power Will Not Turn Off
(Posted by fredpau 10 years ago)
1996 Explorer Turns Over Won't Run
What would cause the 96 explorer to turnover but not run , it is getting fire to the plug wires but ...
What would cause the 96 explorer to turnover but not run , it is getting fire to the plug wires but ...
(Posted by raphdp 11 years ago)