Fluke 787 Support Question
Fluke 787 Support Question
Find answers below for this question about Fluke 787.Need a Fluke 787 manual? We have 2 online manuals for this item!
Question posted by allatseaagain on January 19th, 2022
Fluke 787 Battery Replaced.
When I switch the instrument on it just displays "uncal"... What can I do...?
Current Answers
Answer #1: Posted by SonuKumar on January 19th, 2022 9:27 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
The unit needs to be adjusted. This is done with special adjustment equipment. refer to www.Fluke.com for the calibration manual on the unit.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Fluke 787 Manual Pages
Fluke 787 and 789 Process Meter Datasheet - Page 1
... See page 43
C125 See page 44
PV350 See page 47
Included accessories Fluke-789 ProcessMeter: TL71 Premium Safety-Designed Test Lead Set plus alligator clips, one 9V alkaline battery (installed), product overview and users manual (CD-ROM) in 14 languages. Fluke 787 and 789 ProcessMeter™ Test Tools
Safety rated multimeters with a 4-20 mA...
FE 787 Users Manual - Page 1
Printed in U.S.A. April 1997, Rev.3, 12/01
© 1997, 1898, 2000, 2001 Fluke Corporation, All rights reserved. All product names are trademarks of their respective companies.
®
787
ProcessMeter
Users Manual
FE 787 Users Manual - Page 4
... Manually Stepping the mA Output 25 Auto Ramping the mA Output 26 Power-Up Options...27 Battery Life...28 Using the Holster and Flex-Stand 28 Maintenance ...28 General Maintenance 28 Calibration...28 Replacing the Battery 30 Replacing a Fuse ...31 If the Meter does not Work 32 Replacement Parts and Accessories 33 Specifications...36
Index
ii
FE 787 Users Manual - Page 5
... of purchase immediately.
Your meter is a handheld, battery-operated tool for information about DMM accessories. To order replacement parts or spares, see Table 13 near the end of a digital multimeter, plus current output capability. ProcessMeter
Introduction
WWarning
Read "Safety Information" before you use the meter. Your Fluke 787 ProcessMeter™ (referred to as "the meter...
FE 787 Users Manual - Page 6
... under test.
WWarning
To avoid possible electric shock or personal injury:
• Do not use the meter, inspect the case. Pay particular attention to :
Fluke Corporation P.O. 787 Users Manual
Address correspondence to the insulation surrounding the connectors.
2 Use the meter only as specified in Table 1. International symbols used on the World Wide...
FE 787 Users Manual - Page 8
...
4
Mains, wall outlets, main distribution levels connected closer to the manual for information about this feature. Conforms to relevant Canadian Standards Association directives
Battery
T
Double insulated
Meets Underwriters' Laboratories safety requirements
Inspected and licensed by TÜV Product Services
CAT III
Overvoltage (Installation) Category III, Pollution Degree 2 per...
FE 787 Users Manual - Page 9
... are familiar with the Meter," and begin using your memory about the power-up options, and battery and fuse replacement instructions.
Fluke 787 ProcessMeter
ee014f.eps
5 Display
Rotary Switch
ProcessMeter How to the sections referenced in addition to Get Started
787 PROCESSMETER
MIN MAX % STEP
RANGE COARSE
REL
HOLD H FINE
Hz
mV V
mA A
OUTPUT
mA
V
mA
OFF...
FE 787 Users Manual - Page 12
787 Users Manual
4 3
2 1
5
mV V V OFF
6
mA A
OUTPUT
mA
mA
Figure 3. Rotary Switch Positions for Measurements 8
ee002f.eps
FE 787 Users Manual - Page 14
Rotary Switch Positions for mA Output
ee008.eps
10 787 Users Manual
mV V V OFF
mA A
OUTPUT
mA
mA
1 2
Figure 4.
FE 787 Users Manual - Page 16
...
b U (BLUE)
Figure 5. Pushbuttons
Function(s)
Toggles the backlight Rotary switch in mA A Lposition and test lead plugged into c A jack: Toggles between ac and dc ampere measure Rotary switch in O position: Selects diode test function (D) Rotary switch in OUTPUT mA Jposition: Cycles through
• Slow repeating 0% -100% - 0% ramp (Eon display) • Fast repeating 0% -100% - 0% ramp (P on...
FE 787 Users Manual - Page 24
...− jacks as a current loop with no loop supply.
787 Users Manual
Using the Current Output Functions
The meter provides steady...of output jacks is in use.
20 Source mode depletes the battery faster than simulate mode, so use is to tell which mode... such as shown in an externally-powered current loop. The display looks the same in use simulate mode whenever possible.
Source Mode...
FE 787 Users Manual - Page 26
...seconds, then release K.
22 Simulate mode conserves battery life, so use it instead of the mA output settings BEFORE you turn the rotary switch to a current loop.
The display looks the same in series with overrange to...8722; jacks as shown in Figure 8.
Simulate mode is turned off the meter.
2. 787 Users Manual
Simulate Mode
Simulate mode is in use. The way to tell which mode is...
FE 787 Users Manual - Page 32
... 9. General Maintenance
Periodically wipe the case with a Flex-Stand bail.
Contact a Fluke Service Center for instructions.
28 787 Users Manual
Battery Life
WWarning
To avoid false readings, which could lead to ensure that absorbs shocks and... to possible electric shock or personal injury, replace the battery as soon as the battery indicator (B) appears. Table 12 shows typical alkaline...
FE 787 Users Manual - Page 34
... screw counterclockwise so that the slot is parallel with the screw picture molded into the case. 3. Remove the test leads and set the rotary switch to Figure 10. Replace the battery as follows. Lift off the battery door.
30
Figure 10. 787 Users Manual
Replacing the Battery ! Close and latch the battery door before you use the meter.
FE 787 Users Manual - Page 35
...Fluke PN 943121. Warning
To avoid personal injury or damage to mA A L.
2. Turn the rotary switch to the meter, use only the specified replacement fuse, 440 mA 1000V fast-blow, Fluke... rotary switch to dmA.
5. Make sure the rotary switch is blown:
1. Replace the battery door.
31 Using an ohmmeter, check the resistance between the meter test leads. Remove the battery door.
3. Replacing a ...
FE 787 Users Manual - Page 36
... will be repaired and
returned for a fixed fee.
If there is under warranty, it will be repaired or
replaced (at Fluke's option) and returned at no further attempt to use the meter, and contact a Fluke Service Center.
• Check the battery, fuses, and test leads.
• Review this manual to make no charge. Contact...
FE 787 Users Manual - Page 38
... screw Non-skid foot O-ring for input/output receptacle Battery door Battery door fasteners Keypad Standard test lead set Alligator clips for use with TL75 test lead set Industrial test lead set Product Overview Manual Users Manual (CD-ROM) Calibration Manual (not shown)
Fluke PN or Model no.
614487 CG81G 943121 619962 619939...
FE 787 Users Manual - Page 46
...in L); With holster and Flex-Stand: 638 g (22.5 oz)
42 Certifications: CSA, UL, TÜV Power requirements: Single 9V battery (ANSI/NEDA 1604A or IEC 6LR61) Size: 32 mm H x 87 mm W x 187 mm L (1.25 in H x 3.41 in W x... 7.35 in L) Weight: 369 g (13 oz); 787 Users Manual
Vibration: Random 2g, 5 to 500 Hz Shock: 1 meter drop test Water and dust protection: ...
FE 787 Users Manual - Page 47
... Sourcing, 20 Span (4-20 mA or 0-20 mA), 22 Steady, 24 Stepping, auto, 26 Stepping, manually, 25 With external loop supply, 22
-D-
Diodes, testing, 18 Display, 15
43 -A-
Auto Ramping, 17, 26 Ranging, 17 Stepping, 17
-B-
Battery Replacement, 30
Buttons, 12
-C-
FE 787 Users Manual - Page 48
787 Users Manual
-F- Jacks, 7
-K-
Parts, replacement, 34 Power-up , 27 Output. Input/Output jacks, 7
-J-
mA output. Offset, programming an, 19 Options, power-up options, 27 Pushbuttons, 12 Flex-Stand, 28 Freezing a reading (TouchHold), 19 Fuse, checking and replacing, 31
-H- Holster, 28
-I-
Loop supply, external, 22
44
M- See Current output Mailing address for Fluke, 2 Maintenance, ...
Similar Questions
787 Uncal Message Reset.
how can I reset the unca l error message on my 787 without going thru a complete calibration?
how can I reset the unca l error message on my 787 without going thru a complete calibration?
(Posted by Dludwig421 6 years ago)
Fluke 787 Is Displaying 'uncal'
What does it mean when the "uncal" is dispalyed? It's not in the manual.
What does it mean when the "uncal" is dispalyed? It's not in the manual.
(Posted by holman53360 8 years ago)
Fluke 787 Uncal Displayed
My Fluke 787 is displaying UnCal on the screen. What is it, what does it mean and what do I do to co...
My Fluke 787 is displaying UnCal on the screen. What is it, what does it mean and what do I do to co...
(Posted by jerrysulsar 10 years ago)