Dewalt DWX726 Support Question
Dewalt DWX726 Support Question
Find answers below for this question about Dewalt DWX726.Need a Dewalt DWX726 manual? We have 1 online manual for this item!
Question posted by DonBaileypainting on March 30th, 2023
Can I Replace The Raise And Release Cables
The person who posted this question about this Dewalt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on March 30th, 2023 8:06 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,627,790
Member since:
May 9th, 2021 Points: 16,627,790
Yes, it is possible to replace the raise and release cables on the DeWalt DWX726 rolling miter saw stand. However, it's important to note that replacing the cables may require some technical expertise, as well as the use of specialized tools.
Before attempting to replace the cables, make sure to consult the DeWalt DWX726 owner's manual for instructions and safety guidelines. You may also want to consider reaching out to a professional technician or contacting DeWalt customer service for guidance.
When replacing the cables, it's important to use the correct replacement parts and to follow all recommended procedures carefully. This will help ensure that the stand operates safely and effectively.
https://images.homedepot-static.com/catalog/pdfImages/a4/a40cdd21-914a-46b4-9fd9-0bf736a204b1.pdf
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Dewalt DWX726 Manual Pages
Instruction Manual - Page 3
...that conforms to ANSI Z87.1.
• ALWAYS use only identical replacement parts. The stand will result in death or serious injury. ...WARNING: Indicates a potentially hazardous situation which , if not avoided, may raise unexpectedly when lever is dusty. CAUTION: Indicates a potentially hazardous situation which...released.
• This product was designed to the tool and the accessory.
Instruction Manual - Page 4
... knobs 1 M8 lock washer 1 M6 x 10 mm button head screw 1 M6 lock washer 1 Hex wrench
Tools Required
• Hex wrench (supplied) • Adjustable crescent wrench • 1/2 inch open end wrench •... stand or any part of the stand. To reduce the risk of serious personal injury, do not raise or lower stand until the assembly of the extension work support assembly 1 Handle 2 Wheel 2 Axle ...
Instruction Manual - Page 6
... (I ) with curved washers (M) to attach storage foot and the connector.
3. Use the thumb of your right foot on the other wheel in a raised position.
1. After raising the stand a few inches, release the red activating lever. The stand will automatically lock into place.
With stand right side up on the red activating lever (V). 4. Grasp...
Instruction Manual - Page 7
.... Refer to desired height, place the top piece (H1) of the work support arm on cord wrap screw and finger tighten nut.
5 With the stand raised to the label with the other work support into the hole (Z) from disengaging. Repeat with the arrow pointing down as shown in to hold the...
Instruction Manual - Page 8
...two rails are in place, tighten the rail screws (AA) loosened in the tool's feet.
AA
2. Center the tool, both forward and backward and side to both the instructions in this is bolted...English
2.
Failure to a stand or supporting surface. WARNING: To reduce the risk of your tool manufacturer's manual before assembling the miter saw or planer to heed these warnings may result in ...
Instruction Manual - Page 9
...saws, sliding compound miter saws and planers. WARNING: Any tool used in conjunction with the slots in the mounting rails as the tool base being mounted and a minimum depth of Grade 2. ... inch (19 mm) plywood (See Figure 15 for dimensions).
If binding and/or inaccuracy occurs, replace the plywood with this stand must be necessary under these circumstances. PRODUCT STABILITY TEST (FIG. 16...
Instruction Manual - Page 10
... repeat the test.
8
Stay alert. Make your own safety, use two or more people to
FIG 17
the stand and is raised 2-1/2
FF
inches (63.5 mm) off
the floor.
3.
Ensure the tool is securely mounted to perform the stability test or serious injury could result. Place a 2-1/2 inch
(63.5 mm) thick block
of...
Instruction Manual - Page 11
... lowering the stand. FIG 18
TO ADJUST EXTENSION WORK SUPPORT HEIGHT 1. STORAGE AND TRANSPORTATION
WARNING: TIPPING HAZARD. The stand may raise unexpectedly when lever is released. Refer to To Raise and Lower the Stand under Assembly to adjust the stand to Figure 19 for proper transporting position.
Repeat with the other side. Refer...
Instruction Manual - Page 12
...in certain states or provinces. dewalt.com. Three Year Limited Warranty
DEWALT will maintain the tool and replace worn parts caused by DEWALT, have been made or attempted by a DEWALT factory service ... tested with this product, use of such accessories with this product.
Always use identical replacement parts. To reduce the risk of purchase. This warranty does not apply to faulty ...
Instruction Manual - Page 13
English
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
11
Instruction Manual - Page 40
N116787 DWX726 Copyright © 2011 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; and the array of the tool. the kit box configuration; the array of pyramids on the surface of lozenge-shaped humps on the handgrip; DEWALT Industrial Tool Co., 701 East Joppa Road...
Similar Questions
How To Adjust Cable To Release Mechanism
just put together the dwx726. The release cable too loose the fully disengage and allow the stand to...
just put together the dwx726. The release cable too loose the fully disengage and allow the stand to...
(Posted by Jacsjmac 2 years ago)
Dewalt Stand Will Not Lower
my stand had the 779 miter saw and it has been working well. All of a sudden it stopped lowering. Th...
my stand had the 779 miter saw and it has been working well. All of a sudden it stopped lowering. Th...
(Posted by moses106 4 years ago)
Replace Broken Spring On Dewalt Dwhttr410 Staplegun
How to replace broken spring pushing staples forward on Dewalt DWHTTR410 Staplegun
How to replace broken spring pushing staples forward on Dewalt DWHTTR410 Staplegun
(Posted by Jef1ahr 8 years ago)