Cub Cadet GTX 2100 Support Question
Cub Cadet GTX 2100 Support Question
Find answers below for this question about Cub Cadet GTX 2100.Need a Cub Cadet GTX 2100 manual? We have 3 online manuals for this item!
Question posted by Tyforthree on June 14th, 2020
Deck Lift
have a new deck lift on my gtx 2100. Been using it for about 2 years. Now lift wont raise deck. Soon as it get the weight of the deck on it it stops. Took deck off and it goes up and down fine. What could be the problem.
Current Answers
Answer #1: Posted by techyagent on June 14th, 2020 8:52 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,800
Member since:
June 17th, 2014 Points: 4,799,800
I take it this model has the electric lift switch? have you made sure the switch is clean and connected properly?
Try, removing carefully and check to see if the connections are clean, then use some di-electric grease, and put back together.
This grease can be purchased at any automotive store, if that doesn't work replace the switch with a new one. Also make sure the wiring to all parts in question are intact, and not cut or disconnected, this could be causing a short as well.
Thanks
Techygirl
Related Cub Cadet GTX 2100 Manual Pages
Series 2000 Brochure - Page 1
...DECK LIFT...SmartJet™ Deck Wash System
5-YEAR LIMITED WARRANTY&#...raises the bar above all others. cubcadet.com
locate A DEALER AT
CUBCADET.COM
Innovations no one . Meet the garden tractor that 's smart.
And a cast-iron transmission and front axle give you the envy of the Cub Cadet Signature cut . Garden tractors
SERIES 2000
GT 2000 GT 2100 GTX 2000 GTX 2100
DESIGNED FOR lawn...
Series 2000 Brochure - Page 2
... Lift
Brakes Seat
ADDITIONAL SPECIFICATIONS Front Tires Rear Tires Forward Speed Reverse Speed Fuel Tank Capacity Engine Oil Capacity Transmission Oil Capacity Wheelbase Overall Length
MOWER DECK
Deck Type
Cutting Width/Blades
Deck Cutting Height Deck Drive System Anti-scalping Deck Spindles Deck Pulleys Deck Wash
WARRANTY†
GT 2000
20 HP* Kohler® Command® V-Twin OHV
GT 2100
GTX...
Series 2000 Warranty Information - Page 1
...such as : belts, blades, blade adapters, grass bags, rider deck wheels, seats, and tires. Cub Cadet shall not be free ... lawn care services or for use or exposure. Alteration of safety features of any part found to new merchandise purchased or leased and used in... price of merchantability or fitness for a period of five (5) years or 500 hours, whichever occurs first, commencing on the date ...
GTX 2100 Operator's Manual - Page 1
... MAY RESULT IN PERSONAL INJURY.
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
GT 2000, GTX 2000 & GTX 2100
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Printed In USA
CUB CADET LLC, P.O.
GTX 2100 Operator's Manual - Page 3
... lead and lead compounds, chemicals known to stop the machine and disengage them
which could be used. Thoroughly inspect the area where the equipment ...
9. Never allow children under the cutting deck. by
machine and in serious injury. Loose fitting clothes and... feet.
3 Contact with any type of the mower and attachment discharge direction
from the machine while it...years of yourself and others.
GTX 2100 Operator's Manual - Page 4
... other hidden
19. Do not use on that operators, age 60 years and above, are a major factor related to stabilize the machine by the machine manufacturer. Data indicates that area or serious injury could result in this
4.
Avoid starting or stopping on steep slopes. Mow up slowly.
The mower could suddenly turn slowly and...
GTX 2100 Operator's Manual - Page 5
... or on the ground.
Always place containers on mower).
Be alert and turn " ride-on the ...years of the fuel tank or container opening at least two minutes before storing. On slopes, the weight of the towed equipment may fall off the engine and equipment. Service
Safe Handling of control.
5. Use only an approved gasoline container.
Extinguish all moving parts have stopped...
GTX 2100 Operator's Manual - Page 6
...make adjustments or repairs to be used , it should not be sure the equipment is in this product has an Average Useful Life of seven (7) years, or 390 hours of the ... Operation Practices Mower blades are working condition.
If the blades do not stop within approximately (5) five seconds after operating the blade disengagement control. In the State of the Average Useful Life have ...
GTX 2100 Operator's Manual - Page 7
... children, even with the blade(s) can cause serious personal injury. ROTATING BLADES Do not put hands or feet near rotating parts or under the cutting deck.
WARNING- DANGER -
WARNING- BYSTANDERS Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in operation.
WARNING-
Contact with...
GTX 2100 Operator's Manual - Page 11
...turtle) positions. NOTE: The brake pedal must be used for detailed starting instructions. WARNING! Operating with all features in ...the engine. Refer to operate this manual for sudden stops or setting the parking brake. The brake pedal can... Module Forward Drive Pedal Reverse Drive Pedal Electric Lift Switch
Manual Lift Handle
Cutting Height Lever
Hydrostatic Transmission Dipstick/Fill...
GTX 2100 Operator's Manual - Page 12
..., stop engine and remove key to travel . The cutting height lever can NOT be in the index notch. Press the drive pedal forward to cause the tractor to prevent unintended starting the engine. The further forward the pedal is used to raise the deck. Electric Lift Switch (If so equipped)
LOWER DECK
ELECTRIC DECK LIFT
RAISE DECK
To Operate Electric Deck Lift...
GTX 2100 Operator's Manual - Page 16
... cruise control lever while traveling in the desired setting. 3. Operation Turning up a slope. Using the Lift Lever
Manual Lift Lever (If so equipped)
To raise or lower the cutting deck, move the lift lever to the left foot and hold it is necessary to stop . Tall grass can not be set in that position.
2. Never leave a running...
GTX 2100 Operator's Manual - Page 17
...5-3
NOTE: When operating the tractor be certain that the throttle lever is rotated out of the STOP position.
Section 5 - Move the throttle control lever to premature battery wear and a poor quality... PTO
Engaging the PTO transfers power to the STOP position. The lamps turn OFF when the ignition key is moved to the cutting deck or other (separately available) attachments. Operating the...
GTX 2100 Operator's Manual - Page 19
... individual. Shut the engine off, then check for a few minutes.
Stop the tractor engine and remove the ignition key.
2.
Section 6 - Checking...engine and allow it is
located on the back of the mower on the upper section of the dipstick.
1. After draining the...oil. Replace the oil filter, and refill the engine with new oil as opposed to the Engine Operator's Manual for refilling...
GTX 2100 Operator's Manual - Page 21
...stop . Pivot Hole
Steering Gear Centered
Centering Hole A
C
C
Grease Fittings
D
D
Figure 6-5
3. Pivot Points & Linkage
Lubricate all the pivot points on the drive system, parking brake and lift...should toe-in the centered position. Raise the tractor's hood.
2. Adjustments
...of the tractor deck's gauge wheels is engaged in , proceed as follows:
1.
Using a pressure lubricating...
GTX 2100 Operator's Manual - Page 23
... left side of the notches. Turning adjusting bolt clockwise will increase the effort needed to this spring. See Figure 6-9. Place the deck/attachment into the lowest position for making adjustments to lift the attachment.
Section 6 -
This ensures that the spring is extended the furthest. There should be a downward/forward bias on the...
GTX 2100 Operator's Manual - Page 24
... should read 12.6 volts (DC) or higher across the battery terminals. Position the new battery and lower into the previously noted battery tray hole, then rotate the rod around... Hold Down Rod
Hex Screw
Rotate Upward
Battery Tray
24
Figure 7-1 Disconnect the Negative cable. 2. Lift the battery out off the battery tray and remove from the positive terminal. 2.
See Figure 7-2.
...
GTX 2100 Operator's Manual - Page 26
... properly. 2. Tighten blade and spindle. 2. Perform side-to-side deck adjustment. 2. Excessively high grass. Uneven tire pressure.
8
Remedy
1. Sharpen or replace blade. 3. Damaged or bent cutting blade. 1. Place throttle in all four tires.
26 Troubleshooting
Problem
Excessive vibration
Mower will not mulch grass (If equipped)
Cause
1. Wet grass. 3. Uneven cut
4. Dull...
GTX 2100 Operator's Manual - Page 28
...-850-0008 490-850-0005
42" Staggered Deck 50" Stamped Deck 54" Stamped Deck 46" Snow Blade 44" Snow Thrower 46" Snow Thrower 42" Mulch Kit 48" Fabricated Mulch Kit 50" Mulch Kit 54" Fabricated Mulch Kit 54" Stamped Mulch Kit Twin Bagger Triple Bagger Weight Kits Tire Chains Oil Siphon Blade Removal Tool...
GTX 2100 Operator's Manual - Page 32
...tune-ups, brake adjustments, clutch adjustments, deck adjustments, and normal deterioration of merchantability or fitness...and workmanship for a period of four (4) years or three hundred (300) operation hours, whichever... expenses incurred for substitute or replacement lawn care services or for whom it ... maintenance records to new merchandise purchased or leased and used in your local authorized...
Similar Questions
Cub-cadet-cc30e-lawn-mower
cub-cadet-cc30e-lawn-mower won`t just beeps after inserting the key. The battery fully charged
cub-cadet-cc30e-lawn-mower won`t just beeps after inserting the key. The battery fully charged
(Posted by paulross 1 year ago)
Electric Deck Leveler (motor Replacement?)
I just bought this GTX 2100, Dom, 2012. First time I went to mow, I ran the deck down, and the motor...
I just bought this GTX 2100, Dom, 2012. First time I went to mow, I ran the deck down, and the motor...
(Posted by OldPatriot34 2 years ago)
Won't Turn Over
wont turn over. Battery good, lights work, deck goes up and down
wont turn over. Battery good, lights work, deck goes up and down
(Posted by lovekel2003 4 years ago)
Lawn Mower Not Starting.
Our lawn mower will not start. We replaced battery and now it acts like it wants to crank but won't....
Our lawn mower will not start. We replaced battery and now it acts like it wants to crank but won't....
(Posted by TDivens1972 6 years ago)
Blade Drive Belt Flipping Off And Shredding.
I purchased a Cub Cadet GTX2100, 54" deck and paid $5,000.00 for it. It has only 20 hours of grass c...
I purchased a Cub Cadet GTX2100, 54" deck and paid $5,000.00 for it. It has only 20 hours of grass c...
(Posted by launius07 10 years ago)