Craftsman 28922 Support Question
Craftsman 28922 Support Question
Find answers below for this question about Craftsman 28922 - YT 3000 21 HP 42" Yard Tractor.Need a Craftsman 28922 manual? We have 1 online manual for this item!
Question posted by daHoff on October 8th, 2013
How To Tighten Belt On A Yt 3000 Riding Mower Mower Deck
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Craftsman 28922 Manual Pages
Operation Manual - Page 1
Operator's Manual
1®
LAW TRACTO
21.0 HR* 42" Mower Electric Start Automatic Transmission
Model No. 917.28922
• EspaSol, p. 33
03070
This product has a low emission engine which operates differently from previously built engines. Sat
SEARS, ROEBUCKAND CO., HOFFMAN ESTATES, IL 60179 U.S.A. ...
Operation Manual - Page 2
... amount of engine oil, failure to keep the deck clear of operator negligence, including but not limited to...spark plugs, air cleaners, belts, and oil filters. Normal deterioration and wear of the riding equipment, impacting objects that ...and Adjustments 21
Storage
27
Troubleshooting
28
Sears Service Back Cover
Craftsman Riding Equipment Warranty: Lawn Tractors, Garden Tractors, Zero ...
Operation Manual - Page 3
...riding mower-related injuries. GENERAL OPERATION
• Read, understand, and follow all times. • Only allow the mower to occur. Avoid discharging material against a wall or obstruction. Material may lose control of the tractor... handling.
These operators should evaluate their ability to operate the riding mower safely enough to cause cancer and birth defects
or other safety...
Operation Manual - Page 5
...tighten securely. GENERAL SERVICE
Replace gas cap
• Never operate machine in a closed area.
• Keep all times until fueling is clear of bystanders before storing.
• If you will not have been given rides... injured or interfere with manufacturer's recommended parts,
when necessary.
• Mower blades are sharp.
Clean oil or fuel
spillage and remove any adjustments or...
Operation Manual - Page 8
... area.
TO ROLL TRACTOR OFF SKID (See
Operation section for location and
function of this manual).
8 Continue with all belt keepers.
/ Check wiring...tractor off skid.
5. Be sure tractor is adjusted comfortably and tightened securely.
/All tires are routed properly around pulleys and inside all controls, their location and function. CHECK DECK LEVELNESS
For best cutting results, mower...
Operation Manual - Page 9
... could result in death, serious injury and/or property damage.
9 CAUTION when used to the tractor and/or engine. HOT SURFACES indicates a hazard which can result in serious injury or death. ...REVERSE OPERATION
SYSTEM (ROS)
ENGINE ON ENGINE START
PARKING
_ E21 { j.,
BRAKE
MOWER HEIGHT
MOWER LIFT
LIGHTS ON
FUEL
BATTERY
REVERSE
FORWARD
CRUISE CONTROL
CLUTCH/BRAKE PEDAL
®@®...
Operation Manual - Page 10
... familiarize yourself with the engine off .
(J) MOTION CONTROL LEVER -Selects the speed and direction of tractor.
(M) FREEWHEELCONTROL- Used
for starting and controlling engine speed.
(E) ATTACH M ENT CLUTCH LEVER =Used to engage the mower blades, or other attachments mounted to the applicable safety standards of the American National Standards Institute.
(A) ATTACHMENT LIFT LEVER...
Operation Manual - Page 12
...MOWER CUTTING HEIGHT The position of the attachment lift lever (A) determines the cutting height. Gauge wheels then keep the deck in proper position to over 6 inches in height should be cut with tractor...are slightly off when operating your equipment on mowers so equipped, or the deflector shield
(S) in place.
12 For healthier and better looking lawns, mow often and after moderate growth. ...
Operation Manual - Page 16
... T Lubrication Chart
0 Check Battery Level R Clean Battery and Terminals
Check Transaxle Cooling Check Mower Levelness
Check V-Belts Check Engine Oil Level
v'
v'
Change Engine Oil (with maintenance-free battery. GENERAL RECOMMENDATIONS
The warranty on this tractor does not cover items that will shorten the life of this manual. Some adjustments will attract dust and...
Operation Manual - Page 17
...
Engine "ON" Position (Normal Operating)
17
BLADE CARE
For best results mower blades must be purchased from your
warranty. Replace worn, bent or damaged blades.
_, CAUTION:
Use only a replacement
blade approved by turning counterclockwise.
3.
NOTE: Protect your
tractor. Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).
Special blade bolt is...
Operation Manual - Page 20
...collar to using mower again.
• Plug any holes in mower with bolts and Iocknuts. Engage the mower deck PTO to remove excess
water and to help dry before putting the tractor away.
_IbWARNING...tractor's engine off .
9. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to a dry area, preferably a concrete or paved area. Move the tractor...
Operation Manual - Page 21
...ANY
1. Place attachment clutch in "DISEN-
Roll belt off and push housing guide (P) out of tractor. Disconnect front link (E) from rear mower bracket (D) -
Lower attachment lift lever to "STOP... before sliding mower under tractor.
%
03042tex
21 IMPORTANT: If an attachment other than
the mower is on lift lever when changing position of mower and discon-
Slide mower under right ...
Operation Manual - Page 22
... (J).
. Hook end of link
assembly through front hole in front mower bracket (H) and secure with retainer spring. 4. Install belt onto engine pulley (M) and belt keepers (G).
. iMPORTANT: Check belt for proper routing in arm over pin (D) on opposite side of tractor. 3. Work from left side of tractor.
7. ATTACH REAR LIFT LINKS (C) -
ATTACH FRONT LINK (E) - ATTACH...
Operation Manual - Page 23
... with wrench
lA
and tighten jam nut securely against ad-
23 justment nut.
Test your lawn appears unevenly cut, determine which side of mower or lower the high side. 2. Loosen adjust nut B to lower
mower
side and measure the distance... level side- Iftires are equal.
With all tires properly inflated, park tractor
on tires. Deck must be adjusted so the front tip is cutting lower.
Operation Manual - Page 24
...
and inside all
the way down around both mandrel pulleys and idler pulleys.
3. Pull belt slack toward front of tractor. Make sure belt is
held in this section of all belt guides.
3.
TO REPLACE MOWER BLADE DRIVE BELT
The mower blade drive belt may also check brake by placing
freewheel control in and cam ber are not adjust...
Operation Manual - Page 25
... motion control lever in that position and turn engine off.
4. Tighten adjustment bolt securely.
If your tractor battery to slow leaks, purchase and usetire sealant from accidental grounding. 1.
REPLACING BATTERY
n_a sWbyARaNlloINwGin:g aDworenncoht shoor rat nybaotttehreyr otebrjmeci-t to mower deck
Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc...
Operation Manual - Page 27
...8226; Do not store gasoline from one ounce of this manual). TRACTOR
Remove mower from tractor for storage, do not store battery directly on stabilizer container. ...tractor with a suitable protective cover that all rusted or chipped paint surfaces; Turn ignition key to "START" position for a period of fuel gum deposits during storage. Inspect and replace belts, if necessary
(See belt...
Operation Manual - Page 29
...Cutting too much grass/too fast.
2 Throttle in "CHOKE" position. 3 Build-up of grass, leaves and
trash under mower.
4 Dirty air filter. 5 Low oil level/dirty oil. 6 Faulty spark plug.
7 Dirty fuel filter. 8 ...to 1
run when operator leaves seat with fresh gasoline and replace fuel filter.
10 Connect and tighten spark plug wire.
11 Clean engine air screen/fins.
12 Clean/replace muffler.
13 Check ...
Operation Manual - Page 30
... Shift to slower speed.
3 Wet grass. 4 Mower deck not level.
3 Allow grass to open vent holes. Tighten blade bolt.
7 Buildup of grass, leaves and trash under mower.
4 Bent blade mandrel.
5 Clogged mower deck vent from buildup of grass, leaves, and
open vent holes.
1 Remove obstruction.
2 Worn/damaged mower drive belt. 2 Replace mower drive belt.
3 Frozen idler pulley.
3 Replace idler...
Operation Manual - Page 31
...disengaged" position.
1 Place freewheel control in "engaged" position.
2 Motion drive belt worn, damaged, 2 Replace motion drive belt. ier free!
ou [], [iad. o Get a personatized maintenance ptan for ...(ROS) 1 Turn ignition key to ROS "ON"
is not "ON" while mower or other product manuals onhne.
maaagemySoIaeoCOm
- oGeat nswefrrsomourteamofhomeexperts. TROUBLESHOOTING CHART: See appropriate ...
Similar Questions
How To Install A Clutch Assembly On A Craftsman 3000 Riding Mower
(Posted by imNei 9 years ago)
Yt 3000 21 Hp Yard Tractor By Craftsman How To Clean The Carburetor
(Posted by jobyproo 9 years ago)
Craftsman Riding Lawn Mower Yt 3000 21 Hp 46 Deck Blades Will Not Engage
(Posted by viKgbv 10 years ago)
What Years Was Riding Mower Model Number 917.272140 Produced?
(Posted by Anonymous-59734 11 years ago)
Do They Make A Spray Paint For Craftsman Riding Mower?
(Posted by sdstl 12 years ago)