Canon PIXMA MX712 Support Question
Canon PIXMA MX712 Support Question
Find answers below for this question about Canon PIXMA MX712.Need a Canon PIXMA MX712 manual? We have 8 online manuals for this item!
Question posted by Anonymous-132835 on March 20th, 2014
Error Messsage: B200 & It Said To Unplug Printer. What Is The Problem?
The person who posted this question about this Canon product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by sabrie on March 20th, 2014 5:59 AM
sabrie
Member since:
May 23rd, 2013 Points: 3,306,778
Member since:
May 23rd, 2013 Points: 3,306,778
While a number of things can cause this error code, an overheating printhead is a common cause. Unplug the printer sharply from the power outlet while it is still on > Unplug all cables from the back of the printer > While the printer is off, press and hold the power button for 1 minute, then release > Leave the printer off for 1 hour
Finally, while holding down the stop/cancel button (or just the power button if you don't have those), plug the printer back in, and all cables, then power on the printer if it doesn't do so automatically.
If it is still there, the B200 error indicates that the printhead inside has overheated and shorted out. This can happen when the ink has run out and printing is continued, causing permanent damage to the nozzles, or the printhead voltage is abnormal because there is something wrong with the logic board, either way the printhead and logic board may need to be replaced to make the error go away
Finally, while holding down the stop/cancel button (or just the power button if you don't have those), plug the printer back in, and all cables, then power on the printer if it doesn't do so automatically.
If it is still there, the B200 error indicates that the printhead inside has overheated and shorted out. This can happen when the ink has run out and printing is continued, causing permanent damage to the nozzles, or the printhead voltage is abnormal because there is something wrong with the logic board, either way the printhead and logic board may need to be replaced to make the error go away
www.techboss.co.za
Related Canon PIXMA MX712 Manual Pages
Guide for Printer Setup for Network - Page 1
... Connection
Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection
Push Button Method Standard setup WPS Other setup (Advanced setup)
Disable WEP WPA/WPA2
Wired Connection Preparation for the printer.
Setup Guide
This guide provides information for setting up a network connection for Connection Cable Connection Printer Setup
Character Entry
Troubleshooting
Guide for Printer Setup for Network - Page 2
... something other than "IEEE802.11 n only." • For office use, consult your printer to.
• The configuration, router functions, setup procedures and security settings of the ...with security measures, as there is turned on your personal information to a third party. • This printer cannot be used over wireless and wired connections at the same time. • An "Ad-hoc ...
Guide for Printer Setup for Network - Page 3
...; d-C Connect to WPS-compatible Access Point
• Other setup (Advanced setup) → d-D Connecting to the Network by Entering the Access Point's Settings Directly on the printer but you are unsure if your access point or router supports this technology, press the Stop button and choose Standard setup.
Press the OK button...
Guide for Printer Setup for Network - Page 4
...-Fi lamp on pressing the WPS button, refer to the access point.
3. When the left screen appears, press the OK button.
For details on the printer flashes while searching for about 5 seconds).
Press the OK button on the access point (for or connecting to the access point manual.
2. The network...
Guide for Printer Setup for Network - Page 5
... the network password (WEP key or passphrase) of the screens above will be displayed on the printer. 5. Press the OK button.
6. One of your access point, then press the OK button.
4. Make sure that the network password is case-sensitive.
9.
d-B Standard setup d ...
Guide for Printer Setup for Network - Page 6
... button, refer to the access point.
8. d-C WPS d Connection Using WPS
1. Press the OK button.
3. For details on the printer within 2 minutes. The network connection setup is now complete. Select Push button method. 4.
Select WPS. 2. Press the OK button.
..., press the OK button. Press and hold the WPS button on the printer flashes while searching for about 5 seconds).
Guide for Printer Setup for Network - Page 10
...device vary depending on . b Cable Connection
You will be lit.
Connect the printer and a network device (router, etc.) with security measures, as your system environment. Notes on Wired Connection... Ethernet cable (sold separately).
1. Remove the Cap (A) of the upper port located on one of the printer.
2.
Make sure that the computer and router (A) (or access point) are connected.
• The ...
Guide for Printer Setup for Network - Page 11
Press the MENU button (A) on the printer.
2. c Printer Setup
1. Select Change wireless/wired. 9. Press the OK button.
6. Press the OK button (B).
4. Use the
buttons (A) to select the Setup icon.
3. Press the OK button.
10.Select Wired LAN active. 11. Press the OK button. Select LAN settings. 7. Select Device settings. 5. Press the OK button.
8.
Guide for Printer Setup for Network - Page 13
... above is displayed on -screen keyboard, then press the OK
button to enter more characters. Use the
buttons (B) to select a character from the on the printer. Three types of keyboard (upper case alphabetical, lower case alphabetical and numeric/symbolic) are available.
Guide for Printer Setup for Network - Page 14
... "ANY" SSID, etc.) or disable the stealth mode, then press the left Function button on the printer to change the security protocol (encryption standard) and configure wireless connection settings again. If the problem is Not Detected Check the access point name/network name and network password of the target access...
Guide for Printer Setup for Network - Page 15
... multiple AccessPoints, then press the OK button. An Unknown Access Point is Displayed
Access points in use nearby may be other causes. If the problem is not resolved, there may also be selected. The Access Point Name is Not Displayed Automatically
Refer to the manual supplied with the access...
Guide for Printer Setup for Network - Page 16
... IEEE802.11n, then configure wireless connection settings again. If the problem is set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer will be other causes.
If the problem is set to TKIP, IEEE802.11n cannot be other than TKIP or change...
Guide for Printer Setup for Network - Page 17
... the MENU button. 2. Press the MENU button (A).
2. Select LAN settings > Confirm LAN settings > WLAN setting list to check the MAC address of the printer. 1. Select Device settings, then press the OK button. 4. Use the
buttons (B) to select Wireless LAN setup, then press the OK button. WLAN setting list...
Guide for Printer Setup for Network - Page 18
... setup was not completed within the specified time. The screen appears when an error occurs. Complete the setup within a specified time. Press the WPS button on... refer to the manual supplied with the access point or contact its manufacturer. Timeout error.
Multiple access points are detected. For details on only one access point. Connection failed...
Guide for Printer Setup for Network - Page 19
...Are the access point and printer installed in an open space where wireless communications are found.
If the problem is set as the security protocol (encryption standard) on the printer directly. If SSID broadcast ... same name exist.
Select the MAC address of the target access point on this printer. Wireless connection settings of the access point, refer to change the security protocol (...
Guide for Printer Setup for Network - Page 20
... sure that the MAC address of the access point, refer to change the settings of the printer. 1.
If the encryption standard is inactive, enable the DHCP function and configure wireless...change the settings of the printer will be other than TKIP or change the communication standard to TKIP, IEEE802.11n cannot be other causes. If the problem is Not Displayed Automatically Refer ...
Guide for Printer Setup for Network - Page 21
...sections below to the manual supplied with the access point or contact its manufacturer. If the problem is Not Displayed Automatically Refer to the access point. Select LAN settings > Confi... its manufacturer. Check the access point settings and try again. Wireless connection settings of the printer will be other causes. For details on how to check the specifications of the...
Guide for Printer Setup for Network - Page 22
... are correct. When the setup is inactive, enable the DHCP function or specify the IP address (IPv4 only) of the printer, follow the procedure below. 1. To specify the IP address of the printer and configure wireless connection settings again. Select Device settings, then press the OK button. 4. Select Manual setup...
MX710 series Specifications - Page 1
... or Windows XP pre-installed.
• Windows: Uninstall software bundled with the Canon inkjet printer before upgrading from Mac OS X 10.6 to the operating system's requirements when higher than ...destinations) Regular dialing (with Numeric buttons) Automatic redialing Manual redialing (with the Canon inkjet printer.
Weight Approx. 11.7 kg (Approx. 25.7 lb) * With the Print Head and ink ...
MX710 series Especificaciones [Spanish Version] - Page 1
...Windows XP pre-installed.
• Windows: Uninstall software bundled with the Canon inkjet printer before upgrading from Windows Vista to Windows 7, then install the bundled software again.
.... 1 minute/page at minimum.
Specifications are a theoretical maximum transmission speed between the printer and an equivalent network device, and do not indicate the actual transmission speed obtained. ...
Similar Questions
My Pixma Mx712 Is Displaying Error Code B200 And Will Not Print.
It seems to be stuck in a pause mode. When I attempt to take it out of pause, it just goes right bac...
It seems to be stuck in a pause mode. When I attempt to take it out of pause, it just goes right bac...
(Posted by shelleyechter 7 years ago)
Error C9ode B200
I have an error code B200???? What do I need to do to correct/clear this?
I have an error code B200???? What do I need to do to correct/clear this?
(Posted by dditmeyer 9 years ago)
Is There A Manual With The Canon Printer Pixma Mx712?
(Posted by bpjeRai 10 years ago)
