Canon PIXMA MG3220 Support Question
Canon PIXMA MG3220 Support Question
Find answers below for this question about Canon PIXMA MG3220.Need a Canon PIXMA MG3220 manual? We have 3 online manuals for this item!
Question posted by emc393 on May 5th, 2015
Just Put In A New Color Cartridge....message Screen Reading E And 7.
printer screen flashing "E" and "7".... Will not print. I have rebooted and still the same problem.Any suggestions? Thanks
Current Answers
Answer #1: Posted by Odin on May 5th, 2015 11:37 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Following (in boldface) are the explanation and resolution as provided by Canon, at www.canon-europe.com/support/consumer_products/pro....:
The FINE cartridge is not installed in the correct position.
Resolution
Make sure that each FINE cartridge is installed in the correct position.
The FINE cartridge is not installed in the correct position.
Resolution
Make sure that each FINE cartridge is installed in the correct position.
If the above solution has not resolved your error, please contact your nearest Canon authorised service facility....
You can of course use any repair service you like. For one authorized by Canon, you can phone 800-828-4040.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Canon PIXMA MG3220 Manual Pages
Installation Guide - Page 4
...a direct connection to a network that is not protected with the network connection, refer to the printed manual: Network Setup Troubleshooting. • Place the machine and computer on the same network segment.
...4
Notes on your personal information to a third party. • If an error message appears or if you connect to the computer over a wireless connection without using an access ...
Installation Guide - Page 5
... connection may be copied (installed) to the computer's hard disk. If such a warning message appears, set the security software to access the network. Consult the internet service provider. &#...be required during restarting. Connection fees may appear that Canon software is turned on -screen instructions and do not remove the Setup CD-ROM during the installation. Installing the...
Installation Guide - Page 6
...Drivers & Software
>
Installing the PIXMA MG3220 on Your Wireless Network
If you are installing your printer on the Setup Procedure Selection screen.
6
Be sure to select Wireless Connection on the Connection Method Selection screen and Wireless Setup Using the USB... the Setup CD-ROM that shipped with your printer into your PIXMA. You'll be printing wirelessly in to follow instructions.
Installation Guide - Page 7
Installing the Drivers & Software
Network Guide - Page 2
Connecting to the Network
If any of the following steps to apply the new configuration settings to your Router or Access Point •You want to use a different wireless network •Router settings have replaced your multifunction.
2 Please complete the following situations exist •You have been changed.
Network Guide - Page 5
... it to a computer, software including the drivers needs to be installed.)
IMPORTANT • Log on -screen instructions and do not remove the Setup CD-ROM during the installation process. Consult the internet service provider....once your security software is turned on, a warning message may apply. If such a warning message appears, set the security software to the computer's hard disk.
Network Guide - Page 6
... the printer using a downloaded file. Click here for information. You will be following screen appears after changing the router / Access Point or when connecting to a different network, the settings on the network after starting the setup file or the Mini Master setup, select "Start Setup Again"
6 Connecting to the Network
>
Reconfigure the PIXMA MG3220...
Network Guide - Page 7
Continue carefully following the Printer Setup instructions (Steps 2-1 through 2-3) until the Setup Procedure Selection screen (3-1) appears. Connecting to the Network
>
Reconfigure the PIXMA MG3220 to Your Wireless Network
Be sure to select Wireless Connection on the next page.
7 This is shown on the Connection Method Selection screen (1-2).
Network Guide - Page 8
This is shown on -screen instructions until the Software Installation List appears. This screen is the recommended setup method. You will need to use the supplied USB cable
Continue to the Network
>
On the Setup Procedure Selection screen (3-1) screen, select Wireless Setup Using the USB Cable. Connecting to follow any on the next page 8
Network Guide - Page 10
Connect the supplied USB cable to the Network
>
The drivers and software will install. Connecting to the printer and computer when the Connect Cable screen appears
The Connect Cable screen closes automatically after the printer is detected 10 Continue to follow the on-screen instructions.
Network Guide - Page 11
Connecting to the Network
>
If the Detected Access Points List* appears, select the one you wish to connect to, enter the network key and click connect *This screen normally appears if you have multiple access points or multiple access points exist in your immediate area.
11
Network Guide - Page 12
Connecting to the Network
>
If the Confirm Connection Access Point* screen appears, verify the information then click Yes *This screen normally appears when you have only one access point
12
Network Guide - Page 13
Click Next
>
Setup is now complete. Connecting to exit the setup program. 13 Follow any remaining instructions to the Network
Disconnect the USB cable when the Disconnect Cable screen appears.
Network Guide - Page 14
Installing the Drivers & Software
MAC Network Guide - Page 2
Please complete the following situations exist •You have been changed. Connecting to the Network
If any of the following steps to apply the new configuration settings to use a different wireless network •Router settings have replaced your Router or Access Point •You want to your multifunction.
2
MAC Network Guide - Page 3
...below .
1. Click here to be changed. Click on the Multifunction need to access the MG3220 Drivers & Software page. 2. Connecting to the Network
To re-establish communication on the network...when you originally installed your printer you saved a copy of your computer. 6. Double-click the file, then the Setup icon to start the installation. After reading the details and disclaimer, click...
MAC Network Guide - Page 4
Connecting to the Network
Connect the PIXMA MG3220 to Your Wireless Network If the following screen appears after starting the setup file or the Mini Master setup, select "Start Setup Again"
Follow any instructions until the Connection Method Selection screen appears. 4
MAC Network Guide - Page 5
Continue to the Network
On the Connection Method Selection screen (1-1), Select Wireless Connection. This screen is shown on -screen instructions until the Setup Procedure Selection screen (3-1) screen appears.
Connecting to carefully follow any on the next page.
5
MAC Network Guide - Page 6
You will need to use the supplied USB cable
Continue to the Network
>
On the Setup Procedure Selection screen (3-1) screen, select Wireless Setup Using the USB Cable. This is shown on -screen instructions until the Software Installation List appears. Connecting to follow any on the next page 6 This screen is the recommended setup method.
MAC Network Guide - Page 8
Connecting to follow the on the Connect Cable screen..
8
Continue to the Network
>
The drivers and software will install. Click Next on the Set Up New Printer window, then connect the supplied USB cable between the printer and computer and click Next on -screen instructions.
Similar Questions
Installed New Print Cartriges And Getting Error P And 2
I have the canon MG 3220 and installed new print cartridges . getting errors of P and 2.
I have the canon MG 3220 and installed new print cartridges . getting errors of P and 2.
(Posted by ngermscheid22 8 years ago)
I'm Out Of Ink....how Do I Remove The Cartridges So I Can Put New In.
(Posted by mhponylvr4 9 years ago)
What Slot Does The Color Cartridge Go On A Canon Mx340 Printer
(Posted by ChetAsh 10 years ago)
My Canon Pixma Mg3220 Will Not Print After Loading A New Cartridge.
i loaded the new cartridge. The low ink light would not go out. It printed fine for a few days and n...
i loaded the new cartridge. The low ink light would not go out. It printed fine for a few days and n...
(Posted by jkomar 10 years ago)
Cannot Print! Says Ink Level Of Color Cartridge Cannot Be Correctly Detected.
Yellow light flashing. Put a new color cartridge in.
Yellow light flashing. Put a new color cartridge in.
(Posted by mimistaples 11 years ago)