Brother International LX2500 Support Question
Brother International LX2500 Support Question
Find answers below for this question about Brother International LX2500.Need a Brother International LX2500 manual? We have 2 online manuals for this item!
Question posted by angrimm9 on September 6th, 2013
What Kind Of Thread To Use In Brother Lx 2500 Sewing Machine
The person who posted this question about this Brother International product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Brother International LX2500 Manual Pages
Users Manual - English and Spanish - Page 2
... ignite, resulting in injuries.
5 Special care is being administered.
• Do not use if you notice anything unusual, such as a stove or iron; otherwise, the machine, power cord or garment being used or where oxygen is required when
sewing:
• Always pay close attention to the needle. To reduce the
risk of electric shock...
Users Manual - English and Spanish - Page 3
..., thinner, and scouring powders can damage the case and machine, and should contact your local authorized Brother dealer. This appliance is not intended for use by or near a space heater, iron, halogen lamp...use a fuse
approved by the manufacturer as it could cause the needle to break.
• Do not push or pull the fabric when sewing, and follow the
troubleshooting table in this machine...
Users Manual - English and Spanish - Page 4
... before sewing 18 Starting sewing 18 Trial sewing 19 Changing the sewing direction 19 Sewing thick fabrics 19 Sewing thin fabrics 20 Sewing stretch fabrics 20 Stitching cylindrical pieces 20 Sewing with a twin needle (Option 20 Thread tension 22
3. KNOWING YOUR SEWING MACHINE 4
ACCESSORIES 4 Optional accessories 4
THE MAIN PARTS 5 Flat bed attachment 5
USING YOUR SEWING MACHINE...
Users Manual - English and Spanish - Page 5
... Foot
8 Quilting guide
Part Code
Americas Others
SA125
F001N: XC1944-052
SA127
F003N: XC1945-002
SA134
F018N: XC1976-052
SA132
F016N: XC2215-002
4 1 KNOWING YOUR SEWING MACHINE
1
ACCESSORIES
We have designed these accessories to help you purchased, the following are available as optional accessories to be included with your...
Users Manual - English and Spanish - Page 6
... KD-2902 for use this lever to stitch in the reverse direction.
0 Pattern selection dial (Page 9) Rotate the dial in the foot controller plug and connect the machine to 1 open it.
1
2
1 Flat bed attachment 2 Storage compartment
5
KNOWING YOUR SEWING MACHINE
THE MAIN PARTS
43 2
1
5 A
6 0
7
9
8
1 Bobbin winder (Page 11) This winds the thread onto the bobbin...
Users Manual - English and Spanish - Page 7
... main power first. If the cord or plug is damaged, take the machine to your authorized dealer for the power source. USING YOUR SEWING MACHINE
1
WARNING
● Use only regular household electricity for repairs before continuing use. ● Unplug the power cord if the machine is not to a wall 2 outlet.
2
1
Note
● If a power outage occurs while...
Users Manual - English and Spanish - Page 8
... may bend or break and cause injury.
● Never sew with product code 885-X11. When you press the foot controller down lightly, the machine will increase. only) ● Foot Controller: Model KD-1902
This foot controller can be straight and sharp for home use sewing machine needles for smooth sewing.
1 2
1 Turn on the machine rating plate.
Users Manual - English and Spanish - Page 9
.... Raise the needle by turning the 2 handwheel toward the 5 back of the sewing machine may cause injury.
● Only use an oval screwdriver to turn off the machine. 1 Raise the presser foot lever. screwdriver, otherwise the needle may
break or the machine may cause accident or injury.
CAUTION
CAUTION
● Before replacing the needle, place...
Users Manual - English and Spanish - Page 10
..., the needle may strike the presser foot, which may be damaged. KNOWING YOUR SEWING MACHINE
Lower the presser foot lever and fix the 5 presser foot onto the shank. ...) 1.6 (1/16)
-
1.8 (1/16)
- Pattern selection dial
Patterns and stitch names
CAUTION
● When you use the pattern selection dial to choose a pattern, raise the needle by turning the handwheel toward you turn the pattern ...
Users Manual - English and Spanish - Page 12
... type (part code: SA156, SFB: XA5539-151). KNOWING YOUR SEWING MACHINE
THREADING THE MACHINE
Winding the bobbin
CAUTION
● We designed the bobbin that comes with this machine. Using other models, the machine will not work properly. Then, pass the thread around the pre-tension disk and pull the thread in completely.
2 3
1 Pre-tension disk
2 Bobbin winder shaft
Pull...
Users Manual - English and Spanish - Page 13
... to start.
8
1 Spring on the bobbin.
3
1
2
1
1 1 cm (1/2 inch)
CAUTION
● Make sure you follow the instructions carefully.
Cut the thread, slide the bobbin winder 0 shaft to break. Note
● When the sewing machine is started or the handwheel is wound around the bobbin a few times. If you slide the bobbin winder shaft to...
Users Manual - English and Spanish - Page 14
.... CAUTION
● Make sure you set the bobbin so the thread unrolls in the wrong direction, it may break the needle. KNOWING YOUR SEWING MACHINE
CAUTION
● Not winding the bobbin properly may cause the thread tension to loosen, and may cause the thread tension to sew, you
(counterclockwise) and raise the presser foot lever. Hold...
Users Manual - English and Spanish - Page 15
...use a thread weight of 20 or lower. ● Use the needle and the thread ...threading the upper thread, carefully follow the instructions. For details on page 16 after threading the upper
thread.
1 Groove 2 Projection
Upper threading
2
2
3 4
1 5
1 Spool pin 2 Thread guide (back) 3 Thread guide (front)
4 Thread take-up the lower thread before starting
1
sewing.
Turn off the machine...
Users Manual - English and Spanish - Page 16
... pin and cause the needle to left
as shown in the groove
catches the thread.
1
1 Spring
1
1 Thread take-up lever
Memo
● If the thread take-up lever is not correctly raised, the sewing machine can not be threaded. While holding the thread from right to break. Make sure you raise the needle by turning the 3 handwheel...
Users Manual - English and Spanish - Page 18
... needle Use the ball point needle when sewing on stretch fabrics or fabrics where skipped stitches easily occur.
Using the wrong combination, such as a substitute.
■ Transparent nylon thread Use a 90/14 to be used as heavyweight fabric like denim with a small needle (65/9-75/11), may be uneven, the fabric to pucker, or the machine to...
Users Manual - English and Spanish - Page 19
...care that the mark on the machine.
1
1
Raise the needle by hand, always turn it the other objects during sewing. Turning it toward the rear of thread toward you turn the handwheel by... under the presser foot, 6 pass the thread under the presser foot, otherwise the presser
foot may be injured.
● When you (counterclockwise). If you use the wrong presser foot, the needle may hit...
Users Manual - English and Spanish - Page 20
... press down on page 10 for back tacking and reinforcing seams by turning the a handwheel toward you
(counterclockwise).
Use a piece of the c machine, and then pass the threads
through the thread cutter to cut them.
.
1
Sewing thick fabrics
■ If the fabric does not fit under the presser foot If the fabric does not fit...
Users Manual - English and Spanish - Page 21
When you can use the same color or two different colors of thread for this machine (part code: X57521-021:2.0/75 with the fabric.
If this needle and two top threads.
Sewing with a twin needle (Option)
We have designed your machine so you
have been made for making decorative stitches.
1
1 Basting
Stitching cylindrical pieces
Removing the flat...
Users Manual - English and Spanish - Page 41
.... (For example, you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Turn on the main power switch.
7
The sewing The bobbin-winder shaft is too tight. Use the foot controller properly.
7
Fabric being
sewn with the
machine
Thread is bent or blunt.
Use the oval screwdriver to put it , and...
Users Manual - English and Spanish - Page 42
...; The upper thread breaks.
You have not used a bobbin that are using is not being fed correctly. You have not threaded the upper thread properly or fitted the bobbin properly. The presser foot you are appropriate for this machine.
Correct the upper threading. Choose a thread and needle that you want to sew. Fit the spool properly. Sew with stabilizer material...
Similar Questions
I Need To Know How To Thread A Brother Ls -1520 Sewing Machine?
(Posted by burgessp12 3 years ago)
How To Lower Thread A Brother Lx 2500 Sewing Machine
(Posted by mhidmchug 9 years ago)
How To Thread A Brother Ls 1717 Sewing Machine
(Posted by bdopleli 9 years ago)
How To Thread A Brother Xl 2500 Sewing Machine
(Posted by pgbobdo 10 years ago)
