Bernina Bernette 92C Support Question

Find answers below for this question about Bernina Bernette 92C.
Need a Bernina Bernette 92C manual? We have 1 online manual for this item!

Bernina Overview Questions Manuals Reviews Videos Research

Question posted by ylvalundsten on November 4th, 2023

Main Spool Pin To Bernette 92c

I have brok my main spool pin to my Brenette 92c. The parts that is screwed into the machine, you can have it lying down or fold it up to stand up. Is there an article number so I can search or do you know where to buy this?(NOT THE LOOS SPOOL pin you put in the hole on the top of the machine for e.g. twin stitch)

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on November 4th, 2023 10:20 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,604,600

1,100
points

The part you are looking for is called the spool pin assembly. The Bernina part number for the spool pin assembly for the Bernette 92C is 001770.70.00.

You can purchase the spool pin assembly from a variety of retailers, including:

Sewing Parts Online

Bernina USA

Amazon

Ebay

When you are ordering the spool pin assembly, be sure to specify that you need the assembly for the Bernette 92C.

Here are some instructions on how to replace the spool pin assembly:

Remove the old spool pin assembly by unscrewing the two screws that hold it in place.

Clean the area where the old spool pin assembly was attached.

Apply a small amount of grease to the threads of the new spool pin assembly.

Screw the new spool pin assembly into place.

Tighten the screws until the spool pin assembly is secure.

Once you have replaced the spool pin assembly, you should test it to make sure that it is working properly. To do this, insert a spool of thread into the spool pin assembly and lower the needle bar. The spool of thread should turn freely.

If you have any trouble replacing the spool pin assembly, please consult your Bernina sewing machine manual or contact a Bernina dealer for assistance.

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Answer #2: Posted by arowosadetemitope on March 21st, 2024 11:32 PM

arowosadetemitope

Member since:
February 5th, 2024

Points: 2,400

100
points

I'm sorry to hear about the broken spool pin on your Bernette 92c. While I don't have access to specific article numbers for parts, I can suggest a few general steps you can take to find a replacement:

1. Check the Manual: The user manual for your machine might list the part number for the spool pin. You can often find manuals online at the manufacturer's website².

2. Visit Manufacturer's Website: Bernina, the company that produces Bernette machines, may have a parts list or an online store where you can buy replacement parts directlyS09;.

3. Contact Local Dealers: A local Bernina or sewing machine dealer may be able to order the part for you.

4. Online Retailers: Websites that specialize in sewing machine parts may carry the spool pin you need. You can search for "Bernette 92c main spool pin replacement" to find retailers that might have the part in stock.

5. Sewing Forums and Communities: Sometimes, other sewers may have spare parts or know where to find them. Joining a sewing forum or community online and asking there could be helpful.

Remember to specify that you are looking for the main spool pin, not the auxiliary one, to ensure you get the correct part. If you're unable to find the part number or a retailer, reaching out to Bernina's customer service may be your best option for assistance. They should be able to provide you with the part number and tell you where you can purchase the replacement spool pin.

Sam

Related Bernina Bernette 92C Manual Pages

Operation Manual - Page 2

Table of Contents Introduction ...3 Sewing Machine Needles 4 Thread ...6 Presser Feet ...7 Securing Stitches...8 Turning Corners...9 ... Charts 21 8 Series activa 1008 bernette aurora 12/13/10 artista 3 Series The information in this workbook applies to models equipped with the highlighted feature. 2 Note: Some exercises apply only to all current BERNINA and bernette sewing machines.

Operation Manual - Page 3

... a variety of articles and postings that appeal to all types of America, Inc. After all types of this workbook have to each new issue when it become part of the stitch(...13/10 For more ! Stitch numbers, presser feet, and machine functions are listed for all , the next best thing to sewing is reading about using your BERNINA or bernette sewing machine. Each page that are their ...

Operation Manual - Page 4

...needle is the most inexpensive part in the groove on the back) Needle Size for getting good results and keeping your machine running well. very fine ... sewing projects and your sewing machine but it isn't protected by the hook point Bent - the needle won't pierce fabric, so no thread loop forms to Know Needles... greater the number, the larger the diameter of stitching. European vs.

Operation Manual - Page 5

... on each side. Suitable for decorative and heirloom work . Used for manufactured fibers such as hemstitching. 100 One Universal needle and one shank. thin shaft. Sewing Machine Needles Type Ballpoint Stretch Universal Double Triple Jeans Leather Microtex / Sharp Quilting Topstitch Embroidery Metafil Wing Double Wing Sizes 60-100 70-90 60-120...

Operation Manual - Page 6

... heavier the thread; conversely, higher numbers indicate fine or lightweight thread. Couching, bobbinwork 30 wt.- excellent for quilting as you know that thread passes through the eye of...in less snagging and fraying as it blends into your machine over the long term. Thread To achieve quality stitches, a sewing machine needs three things: correct thread, correct size needle, ...

Operation Manual - Page 8

... at end. Do you know how to sew; Continue stitching the seam; align the raw edges with Rulers bernette Presser Foot: Zigzag/Universal Foot Fold each Needle: 80/12 Universal...be 2" x 6". Sew a few stitches backward; secure the end in reverse until the Quick Reverse Button/Lever is released. machine will automatically secure the stitching, then stop. the machine will sew in the same way...

Operation Manual - Page 9

... the presser foot down or up automatically until reset. Machine will go up . 12/13/10 Do you know how to form at least 2 right angle corners and 2 additional corners. Sew several lines of stitching, pivoting to : ▪...80/12 Universal Needle Position: Center BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot Select the straight stitch.

Operation Manual - Page 10

... Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot Select the Zigzag Stitch (width = 4, length = 2). Move needle position to : ▪Adjust the stitch width? ▪Adjust the stitch length? 10 The needle should lie flat, not roll... using the inside edge of the right toe as a guide. sew using the following steps. Guide the edge of the fabric under the middle of the fabric. or -

Operation Manual - Page 11

... notice that the needle barely stitches into the fabric on the extended hem allowance, keeping the folded edge next to : ▪Machine baste? ▪Distinguish between Blind Hem Foot #5 and Edgestitch Foot #10/10C/10D? 11 Sew on one 6" edge of the fabric using a zigzag stitch and guiding the edge of fabric under...

Operation Manual - Page 12

... Attach Reverse Pattern Foot #1/1C/1D or bernette Zigzag/ Universal Foot to the far right. Sew the seam and press it open. Select the Triple Straight Stitch. Position the edge of the seam, sewing in the same direction as before. 12/13/10 Do you know how to the far left and stitch a second...

Operation Manual - Page 13

...two pieces of the fabric. bernette: Guide the fabric against the blade of the foot and stitch the two layers together. Adjust the stitch length and width if needed. 12/13/10 Do you know how to: ▪ ...Engage the Needle Stop Down feature? ▪ Position Overlock Foot #2/2A? 13 Guide the raw edges of the fabric under the pin of the foot. Select the ...

Operation Manual - Page 14

sew the seam and press it is sewn, adjust the presser foot pressure to a lower number to : ▪ Adjust the presser foot pressure? 14 Stretch Stitch 12/13/10 Do you know how to lighten the pressure of the fabric... be used) Needle Position: As programmed BERNINA Presser Foot: Reverse pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot Select the Super Stretch stitch.

Operation Manual - Page 15

...BERNINA Presser Foot: Clear Embroidery Foot #39/39C/39D bernette Presser Foot: Cording Foot (optional accessory) Attach the ...know how to 6". Stitch ⅝" from one hand? ▪ Adjust stitch width and length? ▪ Drop the feed dog? 15 Tie a knot in the cord at the beginning and end of the stitching and then pull it . Do not sew through the cording, or it won't be able to the machine...

Operation Manual - Page 17

...Select the steps in order and sew them as before trimming. Do you know how to achieve this: • CB Hook Machines: Thread the bobbin thread through ...Fold the cord in front.) Stitch the buttonhole on the stitch plate, behind the foot. lock it in the front grooves and tie the ends in half and loop the middle around the center "toe" of the fabric with bernette models 66 and 92c...

Operation Manual - Page 18

...line, aligning the needle (at the front of the foot. 12/13/10 Do you know how to the line. ▪ Sew the first bead of the buttonhole. Automatic Buttonholes Fabric: Heavy flannel, 6" x 6" and... Automatic Buttonhole on bernette models 66 and 92C, follow the directions on the previous page, looping the cord from the fold along the 6" length. this time as the machine will simply repeat ...

Operation Manual - Page 19

...Hold the thread tails as part of the button by setting...the pin on Button Sew-On Foot #18? 12/13/10 19 Bring the thread tails to sew. ...bernette: Use the Universal or Zigzag stitch, sew 6-8 stitches, and stop. trim the excess thread. the thread tails are secured as you know how to: ▪ Lower the feed dog? ▪ Adjust the shank on Button Sew-On Foot #18 to the machine...

Operation Manual - Page 20

... right side of center. Topstitching the Zipper-bernette Left Side: Adjust the foot to the left of center; Using a straight stitch, sew a ¾" seam from the right side of the fabric and starting at seam and sewing to the right of the zipper. Change to : ▪ Machine baste a seam? ▪ Adjust the needle positions...

Operation Manual - Page 21

...Button Sew-...1 1 9 9 9 6 6 6 15 26 24 3 3 3 2 2 2 3 Series activa classic bernette 380 350PE 330 210 1008 92c 66 56 46* 23 21 -- -- -- -- -- -- -- 7 7 7 5 14 12 11 -- 104...-- 3 6 5 76 2 2 2 2 2 3 3 33 * The stitches on bernette model 46 are not numbered on the machine but are used in the order they appear on the chart in Workbook 1: Basic Operation. ...

Operation Manual - Page 22

Machine Features & Functions The following features and functions are used in Workbook 1: Basic Operation. 8 Series artista Feature/ Function 830 820 730 640 635LE 630... yes yes yes 11 11 11 yes yes yes no no no yes yes yes yes yes yes 3 Series activa mechanical bernette 380 350PE 330 210 1008 92c 66 56 46 yes yes yes no no yes yes yes no yes yes yes yes yes opt opt no yes yes...

Operation Manual - Page 23

...-- -- -- 42 -- -- 50 -- -- -- -- -- -- -- 3 Series activa classic 380 350PE 330 210 1008 92c 1 1 1 1 1 C 2 -- -- -- 2 -- -- -- -- 3 3 -- 3A 3A 3A -- ...-- -- -- 12/13/10 bernette 66 56 C J -- -- -- Darning Foot #9 -- -- -- 9 -- 9 Button Sew-On Foot #18 18 -- 18 -- -- -- The BERNINA name and numbers are included with the purchase of...