Bernina 807 Support Question
Bernina 807 Support Question
Find answers below for this question about Bernina 807.Need a Bernina 807 manual? We have 1 online manual for this item!
Question posted by Suttonrose5 on October 31st, 2023
Inserting A New Needle
What is position of needle when changing to a new needle
Current Answers
Answer #1: Posted by SonuKumar on October 31st, 2023 9:23 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
When changing to a new needle on a Bernina 807, the needle should be in the highest position. This is to ensure that the needle is properly inserted into the needle holder and to prevent the needle from hitting the needle plate when you start sewing.
To move the needle to the highest position, turn the handwheel towards you until the needle reaches the highest point. You can also use the needle up/down button on the machine to move the needle to the highest position.
Once the needle is in the highest position, you can loosen the needle screw and remove the old needle. Then, insert the new needle into the needle holder and tighten the needle screw.
Here are the steps on how to change a needle on a Bernina 807:
Turn off the machine and unplug it from the power source.
Raise the needle bar to its highest position by turning the handwheel towards you.
Loosen the needle screw using a small screwdriver.
Remove the old needle and insert the new needle with the flat side facing the back of the machine.
Tighten the needle screw.
Lower the needle bar and plug the machine back into the power source.
You are now ready to sew!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Bernina 807 Manual Pages
Manual - Page 2
... elastic seams Inserting the bobbin Inserting zips Lace in material Lace on tricot Lap hemmer Looping
Lowering drop-feed control Lycra seams Marking Material gathering Material patching Monograms Needle position Needle table Normal gathering Oiling, Model 807/810 Oiling, Model 817 Overlock Patching material
Patching tricot Perforating Pintucking Plain stitching Quick seam Reverse sewing Ruffling...
Manual - Page 3
...when changing the light bulb, the needle, presser loot, bobbin or needle plate, when stopping work without supervision and during servicing (cleaning).
General information
Max. Name: Address: Date of machine (807)
approx. 8,1 kg
Weight complete with carrying case (807) approx. 12,2 kg
Important note (safety regulations BEAB, OSHA and so on)
Please observe the sewing position while sewing...
Manual - Page 4
... parts of the machine
• rt
10 11 12
13
14
8
7
BERNINA
6
5
II
4 3 2
1
fl
a4
24 23 22
21
2
Model 807
15 16
17 18 19 20
.0"
1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 Thread ... 16 Handwheel release 17 Left-center-right adjusting knob
(needle position) 18 Zigzag adjusting knob 19 Stitch length adjustment
(stitch length lever) 20 Drop-feed control ...
Manual - Page 5
...817 The various parts of the machine
a
10 11 )112 im2l5im.13
14
IS 10
1 Olink•MA
5
4 3 2
L
24
22
1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 Thread regulator 6 Face-...-center right adjusting knob
(needle position) 18 Zigzag adjusting knob 19 Stitch length adjustment
(stitch length lever) 20 Drop-feed control 21 ,,Fast-Slow Sewing.>
motor control 22 Free-arm...
Manual - Page 6
...change the bulb. First compare voltage
specified on the free arm, is used for connecting Bernina sewing machines.
ii -4 I>
Warning! Sewing lamp: 15 watts Connecting to left. To insert bulb, turn anti-clockwise and draw downwards.
After
inserting...machine then runs at reduced speed. Unpacking and packing the machine Model 807, 810
Electrical Connection
Model 807
Sewing machine...
Manual - Page 7
... be regulated. II
-4101limpilsor
5
Turn hand wheel towards you until the needle -mod is an advantage with many kinds of the bobbin case is carried out in its highest position.
Now the machine runs with the existing mains voltage. The insertion of sewing to reduce the speed of the starter. First compare voltage specified on...
Manual - Page 8
Turn hand-
wheel towards you, until needle reaches highest point.
Use only needle system 705 B for darning are numbers 80. 90 and 100 while those for Bernina sewing machines 807, 810 and 817.
The insertion of the bobbin case Is carried out in the same manner.
6
The presser foot with thumb and forefinger of the left hand...
Manual - Page 10
... back leaving a loose end of the ten- in their highest positions.
Model 807 and 810 Darning. Loosen the needle clamp screw half a turn the hand wheel towards you until the takeup lever is
led from the front to be regulated for certain kinds of sewing, mainly when darning.
Place spool on pin. For all...
Manual - Page 11
... into its highest position by means of the lever at hand. It is made in no time. The lever on and
I
tf; To secure the sewing
table the lever ...changes. I
push lever downwards.
Model 807 and 810
Fitting the attachment table.
Changing the presser feet
Use the correct presser foot for sewing. Raise presser foot by pulling to the left. The presser
foot is secured and the machine...
Manual - Page 12
... 0 to the left. zag stitch.
thread - Satin Stitch / Zigzag Sewing
Stitch length:
Needle position: centre Zigzag width:
1 1,5 2 2,5 3 3,5
1
4 Satin stitch spacing
2
3
0
4
2
3
4
close to 0
a g
g a t"
Zigzag sewing
The satin stitch spacing can be moved
while sewing but when the machine Is
stationary only if the needle Is out of the
material. rately adjusted with the...
Manual - Page 19
...sew it on to the seam just where the scissors are unavoidable at least the corners should not be rounded.
18
then a second time one presser foot width from the first seam. Needle position...: centre
Automatic:
zigzag VWWvW (1)
Drop feed control: sowing
Baste the new piece on , first Whenever possible make the patches in...
Manual - Page 24
... stitch. Hold scissors correctly.
23 11D it
41
-' I Zigzag foot 000 Needle. 80-70 Thread: 50
Lace (and insertion) in material
Needle position: centre
Automatic:
zigzag WVWVW (1)
Drop feed control: sewing :
^t 1st run
Stitch width: Stitch length:
about 1
Pin in lace, baste it and sew on with straight stitch]
2nd run
Stitch width: Stitch length:
l'h-2'h according...
Manual - Page 26
.../
Needle position: right
Drop feed control: sewing
Automatic:
Blindstitch
n (2)
Blind hem stitch
V )
This Is how the work is the correct way. Adjust the zigzag so that they can " feel" the regular feeding of the fold. Very poor position. AAMMelYNNPNVv).vyvVo.V.VVV\V\. vvvwvomAN.YA
Oversew and prepare the hem as die gram, baste with machine or...
Manual - Page 29
... clockwise with reinforcing cord
Set machine.
Sew satin stitch for the satin stitch. (Page 10)
will reinforce the buttonhole where the button will be In the left hand and turn work to be regulated to suit the material. How to be changed. Under no circumstances should the zigzag or needle position be used.
Do not...
Manual - Page 34
...sew across the new wool threads with one or two stitches, and leave the needle down the wool with zigzag. The Model 807, 810 only zigzag rows should not overlap nor lie apart from one another .
33 Do not make too deep a curve at the presser foot. Lay the wool in mind:
Model 807...:
zigzag WMWV (1)
Drop feed control: lowered
Thread machine with wool
1st run : Oversewing the threads Cut the...
Manual - Page 36
...
Nro
1.1
i1ili
ti
itre
.0)1. Hint: The easiest way to insert a zip
Sew seam Jirst with the needle position left or right
Drop feed control sewing
142
t'
• 3 .1
Inserting zips
Ttirlise; ht
t
The zip is basted in . Open the zip before you sow it in by the material.
Sew down each side from top to bottom, once with...
Manual - Page 48
... foot and for pintucking
1 Inrarm nr.n;
Stitch width: Stitch length:
You should therefore proceed thus:
Needle position:
0-212/ about 112/
Automatic:
straight stitch
Needle position: centre
Drop feed control: sewing
The gimp Is threaded like this : model 807, 810
(0)
To sew pintucks, 2 top threads are ont twisted together, but bring between or
points in one stitch, as...
Manual - Page 53
...that the spring
snaps back into position. Test by turn-
inserted the hinged shuttle cover can be taken out and the
*
If the machine has been standing in a
...The cover plate of thread and fluff collect under the needle plate and around the hook. During sewing pieces of the free arm should he brought into ...Model 807. 810
Cleaning the machine. so that it can then be turned down.
Manual - Page 54
The sewing machine should be removed.
A
4 1,
Removing frame cover (Model 807) The frame cover is raised slightly under spring tension by pressing the release knob (see illustration) and can easily be disconnected from the power supply by pulling out the plug from the socket when changing the light bulb, the needle, presser foot, bobbin or needle plate...
Manual - Page 55
... the release
Insert bobbin case and close needle knob (see illustration) and can be put in its be disconnected from the power supply by turning the handwheel as screwdrivers and scissors for removing thread particles.
54
Important note (safety regulations BEAB, OSHA and so on)
Please observe the sewing position while sewing. The sewing machine should be...
Similar Questions
Motor For Bernina 807
I need of an electric motor for a bernina sewing machine that was bought in 1974
I need of an electric motor for a bernina sewing machine that was bought in 1974
(Posted by antondup52 3 years ago)
Bernina 950 Sewing Machine
How to oil a Bernina industrial 950 sewing machine?
How to oil a Bernina industrial 950 sewing machine?
(Posted by vhermean 8 years ago)
Oiling Bernina Sewing Machine 807
How do I open the top of Bernina 807 to oil it?
How do I open the top of Bernina 807 to oil it?
(Posted by inadebr 10 years ago)
Bernina 1090 S Sewing Machine Manual
I Dont See The User Manual For This Machine For Free Downloading.what User Manual Are The Same As Th...
I Dont See The User Manual For This Machine For Free Downloading.what User Manual Are The Same As Th...
(Posted by cynthianel 10 years ago)
