Amana NTW4600YQ Support Question
Amana NTW4600YQ Support Question
Find answers below for this question about Amana NTW4600YQ.Need a Amana NTW4600YQ manual? We have 4 online manuals for this item!
Current Answers
Related Amana NTW4600YQ Manual Pages
Installation Instruction - Page 2
... (2 pack)
Alternate parts: (Not supplied with flat washers
To order, please refer to improve performance and minimize noise and possible "washer walk". To order, please refer to 1" (25 mm...Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" ...
Installation Instruction - Page 3
...(143 kgs). n Floor must be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. DRAIN SYSTEM
Drain system can be at least 39" (990 mm) above floor; If a ...138-690 kPa). n A grounded electrical outlet located within 3 ft (0.9 m) of hot
and cold water fill valves on washer, and water pressure of drain hose should be inside standpipe or below 32° F (0°...
Installation Instruction - Page 4
... n Do not have a fuse in the neutral or ground circuit.
48" (1.2 m)
Move washer to have the properly grounded outlet installed by a qualified electrician. IMPORTANT: Removing shipping base is ... only this time.
4 or 20-amp, fused electrical supply is properly grounded.
If your washer includes a sound shield, please refer to the instructions included with a qualified electrician if you ...
Installation Instruction - Page 5
... to free from tray. IMPORTANT: 4.5" (113 mm) of drain hose, slide it over console to allow free access to step 6. For a laundry tub or standpipe drain, go to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of drain hose should be used.
5
do not force excess...
Installation Instruction - Page 6
...for future reference.
You may enter washer.
n Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are only connecting to a cold water faucet, you will need to... sealants on water faucets to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to washer correctly.
A small amount of the drain hose. Repeat this step with separate ...
Installation Instruction - Page 7
... block. Then turn jam nuts counterclockwise on top edges of sides.
Secure drain hose
Laundry Tub
Standpipe
Wall
14.
Tighten leveling feet
Jam nut
With washer in its final location, place a level on leveling feet tightly against washer cabinet. Adjust leveling feet
Jam nut
Secure drain hose to make sure all four feet...
Installation Instruction - Page 8
... or detergent dispenser (on some models).
q Read "Washer Use" in your tools. Start washer and allow to see what was skipped. q Check that washer is an extra part, go back through steps to complete full cycle.
8 q To test and clean your washer, measure 1/2 of normal
recommended amount of washer. Close lid. Select any tape
remaining on...
Use and Care - Page 2
WASHER SAFETY
2
Use and Care - Page 3
... is lit, the lid is paused. If you need to open .
■■ Washer will hear water enter the washer as the lid lock goes through a self-test.
Spray Rinse
Select cycles default to unlock. This delay in the cycle you will not begin to unlock. Lid Locked
To allow for higher spin speeds...
Use and Care - Page 4
... time. You will hear a click, and the lid will hear sounds similar to start the selected cycle; Fabric softener will come on all models. SPIN
The washer spins the load at different stages in a cold and cool water wash, some warm water may hear the motor turning on briefly (short hum) to resume the...
Use and Care - Page 5
...Warm Cool Cold
Hot Warm Cool Cold
Hot Warm Cool Cold
Hot Warm Cool Cold
Hot Warm Cool Cold
Hot Warm Cool Cold
Cold rinse only
High Use this cycle for lightly soiled cottons and mixed fabric loads. High Use this cycle...this cycle for cleaning the interior of the washer. Use this cycle to drain washer after cancelling a cycle or completing
a cycle after power interruption.
This cycle ...
Use and Care - Page 6
... bleach laundry boost product, add to avoid pilling.
USING YOUR WASHER
1. ...cycle, water temperature, and colorfastness.
■■ Separate heavily soiled garments from lightly soiled.
■■ Separate delicate garment from sturdy fabrics.
■■ Do not dry garments if stains remain after washing, because heat can set stains into the bottom of detergent to your laundry...
Use and Care - Page 7
... be set to YES to ensure proper distribution at correct time in the same cycle with warm water until the washer has completed filling, press the START/Pause/Unlock Lid button to YES. Do not... press the START/ Pause/Unlock Lid button again to reduce wrinkling and tangling.
4. Load laundry into washer. For best results, do not pack the load tightly. Items need to Wash Load
During...
Use and Care - Page 8
... and snaps. Suggested Fabrics
Whites and pastels Durable garments Heavy soils
Warm
Some cold water will be cooler than what your previous washer provided.
You will be added to YES.
10. Small will ... on your tap cold water is the temperature from your garments.
This is added to restart the cycle. Select LOAD SIZE
Wash Temperature
Cold
This is very cold, warm water may be cooler...
Use and Care - Page 9
.... c. Do not place an affresh® Washer Cleaner tablet in undesirable odor.
2. U se warm and hot wash water settings sometimes (not exclusively cold water washes), because they do not interrupt cycle. e. Close the washer lid. NOTE: For best results, do a better job of the washer.
Close the washer lid. e. Select the cycle recommended for more than is recommended...
Use and Care - Page 10
Close lid and place tape over edge and into washer basket.
7. Before using again, run washer through Casual Regular cycle to locate, level, and
connect washer. 2. Use half the manufacturer's recommended amount of washer. Disconnect drain from back of washer.
4. Drape power cord over lid and down front of detergent for a medium-size load.
10
REINSTALLING/USING...
Use and Care - Page 11
...on (indicating that the washer was unable to fill appropriately)
Check for leaks (laundry tubs, drain pipe, water pipes,
drain.
Noises
See "Cycle Guide" and "Using Your Washer".
Clicking or metallic noises...must be in firm contact with periodic gurgling or surging as expected
Washer won't run or fill, washer stops working or wash light remains on . Tighten fill-hose connection.
Make...
Use and Care - Page 12
... working or wash light remains on (indicating that the washer was unable to fill appropriately) (cont.)
Check proper electrical supply. Use drain hose form and securely
drain hose installation. Lid must be rearranged to remove excess water. Replace any clogs from drain
standpipe farther than cycles with lower spin speeds remove less water...
Use and Care - Page 13
...cycle with dry items only. See the "Cycle Guide" to match your previous washer. Adding detergent on load after washing
Washer not loaded as recommended.
Reduce tangling by mixing types of load items. Use the recommended cycle for the type of load.
Make sure hot and cold... to both washer and faucet, and have water flowing to inlet valve. This includes cooler hot and warm washes. Sand...
Use and Care - Page 14
... fasteners before washing. Load with the lid open. Using too much detergent. Not washing like colors together and remove promptly after washer has started. damaged before washing
pockets during wash cycle. TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.amana.com/help for fabric type. If you...
Similar Questions
Fabric Softener Dispenser Not Working
My washing machine doesn't dispense fabric softener anymore. At the end of the wash cycle the dispen...
My washing machine doesn't dispense fabric softener anymore. At the end of the wash cycle the dispen...
(Posted by Tkessaram 2 years ago)
Washer Shakes Wildly ,drum Banging On Cover,during Beginning Of Spin Cycle.
washer shakes wildly.
washer shakes wildly.
(Posted by MALSWORD 7 years ago)
Amana Washer Model Number Ntw4600yq Ww
Washer will not fill. I disconnect the lid lock cause it kept flashing
Washer will not fill. I disconnect the lid lock cause it kept flashing
(Posted by Otheahc 8 years ago)
When Washer Goes Into Cycle To Fill And Then The Lid Lock Is Suppose To Engage
When you start washer the fill light comes on and then the lid lock is suppose to engage and then fi...
When you start washer the fill light comes on and then the lid lock is suppose to engage and then fi...
(Posted by Cindymbrister 10 years ago)
I Have An Amana Washer #ntw4600vqo Trying To Stop The Violent Spin Cycle,help
Ever since we have had this washer we havn't been able to stop the violent spin cycle. Tried to leve...
Ever since we have had this washer we havn't been able to stop the violent spin cycle. Tried to leve...
(Posted by rojoinc4165 11 years ago)