User Guide
Page 47
...system is turned on and functioning properly. The link to this port or the Switch is a hardware failure. The system is rebooting and performing self-diagnostic tests. ...Green Blinking The port is transmitting/receiving to a 1000 Mbps Ethernet network is not ready/malfunctioning. ES-2108 Series User's Guide 47 Chapter 3 Hardware Overview 3.3 LEDs The following table describes the LEDs... connection. The port is up. The link to the connected device that supports PoE. No device is connected to an Ethernet network but not receiving or transmitting data...
...system is turned on and functioning properly. The link to this port or the Switch is a hardware failure. The system is rebooting and performing self-diagnostic tests. ...Green Blinking The port is transmitting/receiving to a 1000 Mbps Ethernet network is not ready/malfunctioning. ES-2108 Series User's Guide 47 Chapter 3 Hardware Overview 3.3 LEDs The following table describes the LEDs... connection. The port is up. The link to the connected device that supports PoE. No device is connected to an Ethernet network but not receiving or transmitting data...
User Guide
Page 66
... being used) and the duplex (F for full duplex or H for half duplex). Rx KB/s This field shows the number of received frames on the Switch. 66 ES-2108 Series User's Guide Use this screen to Figure 30 on this port. State If STP (Spanning Tree Protocol) is enabled (On) or disabled (Off...) on page 67). PD (PWR model Only) This fields displays whether PoE (Power over Ethernet) is enabled, this port. RxPkts This field shows the number ...
... being used) and the duplex (F for full duplex or H for half duplex). Rx KB/s This field shows the number of received frames on the Switch. 66 ES-2108 Series User's Guide Use this screen to Figure 30 on this port. State If STP (Spanning Tree Protocol) is enabled (On) or disabled (Off...) on page 67). PD (PWR model Only) This fields displays whether PoE (Power over Ethernet) is enabled, this port. RxPkts This field shows the number ...
User Guide
Page 72
... firmware including the date created. even if the PoE device requested for PoE. Note: The Switch must have at least 16 W of the Switch for identification purposes. Chapter 7 Basic Setting Figure 32 Basic Setting > System Info (ES-2108PWR) Figure 33 Basic Setting > System Info (ES-2108-G) The following table describes the labels in Watts the PWR model...
... firmware including the date created. even if the PoE device requested for PoE. Note: The Switch must have at least 16 W of the Switch for identification purposes. Chapter 7 Basic Setting Figure 32 Basic Setting > System Info (ES-2108PWR) Figure 33 Basic Setting > System Info (ES-2108-G) The following table describes the labels in Watts the PWR model...
User Guide
Page 83
... the connection speed by detecting the signal on the ES-2108-LC, select Auto or 1000M/Full Duplex. A powered device (PD) is a device such as an access point or a switch, that supports PoE (Power over Ethernet) so that both ends support. When auto-negotiation is used in order to connect. Flow Control is... to temporarily stop sending signals and resend later. Back Pressure flow control is turned off or loses power, so use the Save link on the ES-2108-F. The Switch loses these changes if it to obtain the connection speed and duplex mode that it can receive power from the...
... the connection speed by detecting the signal on the ES-2108-LC, select Auto or 1000M/Full Duplex. A powered device (PD) is a device such as an access point or a switch, that supports PoE (Power over Ethernet) so that both ends support. When auto-negotiation is used in order to connect. Flow Control is... to temporarily stop sending signals and resend later. Back Pressure flow control is turned off or loses power, so use the Save link on the ES-2108-F. The Switch loses these changes if it to obtain the connection speed and duplex mode that it can receive power from the...