User Guide
Page 1
...the settings of up to match. Transmitter(s)/ Receiver(s) Code Group "A" Group "A" © 2008 HeathCo LLC Group "B" 598-1306-04 See page 2 for a variety of Switch) Example 1 - All products work together. Heath®/Zenith wireless lighting controls are UL/cUL and/or FCC/IC tested and approved. • Operational range of...the same code setting information. This manual applies to a different code. Simply determine which receiver(s) and set each system to the following products: • Wireless Transmitters (Indoor / Outdoor) - 180° Motion Sensor - 240°...
...the settings of up to match. Transmitter(s)/ Receiver(s) Code Group "A" Group "A" © 2008 HeathCo LLC Group "B" 598-1306-04 See page 2 for a variety of Switch) Example 1 - All products work together. Heath®/Zenith wireless lighting controls are UL/cUL and/or FCC/IC tested and approved. • Operational range of...the same code setting information. This manual applies to a different code. Simply determine which receiver(s) and set each system to the following products: • Wireless Transmitters (Indoor / Outdoor) - 180° Motion Sensor - 240°...
User Guide
Page 2
... NIGHT NIGHT ONLY 1234 CODES DETECT 180° Motion Sensor Code Switches CODES DETECT 1 2 3 4 DAY NIGHT NIGHT ONLY 240° Motion Sensor CR2032 3 VOLTS ON 1 2 34 Code Switches Entry Switch Code Switches LAMP MODE switches RAINTIGHT ã THIS END UP OUTDOOR USE ONLY. FOR WALL AND CEILING MOUNT ONLY SUITABLE FOR WET LOCATION MADE IN CHINA Floodlight...
... NIGHT NIGHT ONLY 1234 CODES DETECT 180° Motion Sensor Code Switches CODES DETECT 1 2 3 4 DAY NIGHT NIGHT ONLY 240° Motion Sensor CR2032 3 VOLTS ON 1 2 34 Code Switches Entry Switch Code Switches LAMP MODE switches RAINTIGHT ã THIS END UP OUTDOOR USE ONLY. FOR WALL AND CEILING MOUNT ONLY SUITABLE FOR WET LOCATION MADE IN CHINA Floodlight...
User Guide
Page 3
... 3 4 DAY NIGHT NIGHT ONLY 180° Motion Sensor (Rear View) 240° Motion Sensor (Rear View) Battery Compartment 598-1306-04 Slide the DETECT switch to mounting bracket. Tighten clamp screw. Attach motion sensor mounting bracket to detect motion day and night or night only. Make sure ...unit has an unobstructed view. IMPORTANT: The motion sensor must be mounted with the bottom cover...
... 3 4 DAY NIGHT NIGHT ONLY 180° Motion Sensor (Rear View) 240° Motion Sensor (Rear View) Battery Compartment 598-1306-04 Slide the DETECT switch to mounting bracket. Tighten clamp screw. Attach motion sensor mounting bracket to detect motion day and night or night only. Make sure ...unit has an unobstructed view. IMPORTANT: The motion sensor must be mounted with the bottom cover...
User Guide
Page 4
... Controls 598-1306-04 Do not overtighten clamp screw. 3. To increase sensitivity, turn the RANGE control toward MAX. Set the DETECT control switch to accent mode. 1. These air sources could cause false triggering. • Areas where pets or traffic may trigger the control. • ...Nearby large, light colored objects reflecting light may result in some environments. Slide the ON-TIME control to Dawn IMPORTANT: Avoid Aiming Motion Sensor At: • Objects that change the coverage area. Select amount of time desired for the selected ON-TIME (1 or 5 minutes) then ...
... Controls 598-1306-04 Do not overtighten clamp screw. 3. To increase sensitivity, turn the RANGE control toward MAX. Set the DETECT control switch to accent mode. 1. These air sources could cause false triggering. • Areas where pets or traffic may trigger the control. • ...Nearby large, light colored objects reflecting light may result in some environments. Slide the ON-TIME control to Dawn IMPORTANT: Avoid Aiming Motion Sensor At: • Objects that change the coverage area. Select amount of time desired for the selected ON-TIME (1 or 5 minutes) then ...
User Guide
Page 9
Install the mounting strap as shown. Set the LAMP MODE switch to the desired light turn -on effects) available when motion is no longer detected and after selected ON-TIME. • FLASH - Note: Do not rotate the lamp holders more than 180° from the light .... Light instantly comes on fixture. Light gradually dims to half-bright, pauses, and then continues dimming to off twice before turning on then off when motion is detected: • NORMAL or - Twist the junction box wires and fixture wires together as shown using two screws that fit your junction box. ...
Install the mounting strap as shown. Set the LAMP MODE switch to the desired light turn -on effects) available when motion is no longer detected and after selected ON-TIME. • FLASH - Note: Do not rotate the lamp holders more than 180° from the light .... Light instantly comes on fixture. Light gradually dims to half-bright, pauses, and then continues dimming to off twice before turning on then off when motion is detected: • NORMAL or - Twist the junction box wires and fixture wires together as shown using two screws that fit your junction box. ...
User Guide
Page 10
...as 5, 6, and 7 above . 1. Short term power line failure. 2. Verify switched device is turned on transmitter and receiver units do not match. 8. Check for 90 second initialization period (remote motion sensor). 5. Verify code settings on device is subject to : HeathCo LLC P.O. If... randomly. You may cause undesired operation. Does not respond immediately after installation. 5. Weak battery in the transmitter. 7. Switch on transmitter and receiver units are being blocked, or transmitter is cautioned that may also write* to the following information available...
...as 5, 6, and 7 above . 1. Short term power line failure. 2. Verify switched device is turned on transmitter and receiver units do not match. 8. Check for 90 second initialization period (remote motion sensor). 5. Verify code settings on device is subject to : HeathCo LLC P.O. If... randomly. You may cause undesired operation. Does not respond immediately after installation. 5. Weak battery in the transmitter. 7. Switch on transmitter and receiver units are being blocked, or transmitter is cautioned that may also write* to the following information available...