Owners Manual
Page 2
...and/or damage to the speaker. • When moving the speaker, do not use chemical solvents (e.g., alcohol or thinners, etc.): this might damage the finish. A vessel with a rated output power higher than the nominal input power of vibrations and water spills...8226; Install the speaker in detergent diluted with the cloth. Contact qualified YAMAHA service personnel when any reasons. • Secure placement and installation is needed. YAMAHA shall not be liable for any service is the owner's responsibility. PRECAUTIONS Read this before using an amplifier with ...
...and/or damage to the speaker. • When moving the speaker, do not use chemical solvents (e.g., alcohol or thinners, etc.): this might damage the finish. A vessel with a rated output power higher than the nominal input power of vibrations and water spills...8226; Install the speaker in detergent diluted with the cloth. Contact qualified YAMAHA service personnel when any reasons. • Secure placement and installation is needed. YAMAHA shall not be liable for any service is the owner's responsibility. PRECAUTIONS Read this before using an amplifier with ...
Owners Manual
Page 3
...; Connect one speaker is switched off. The positioning of speakers is capable of standard connections and biwire connection. Use the other wire of the cable to the floor. English 1 En NS-B750 Loosen Short bar Black (-) Insulation coating NS-B750 Tighten Red (+) Bare wire NS-B750 Subwoofer Center Speakers output terminals of the amplifier (or receiver) SPEAKERS R +- L A -+ B Surround back Surround Notes • Placing this dictates the overall sound quality of the multi channel system. If one speaker...
...; Connect one speaker is switched off. The positioning of speakers is capable of standard connections and biwire connection. Use the other wire of the cable to the floor. English 1 En NS-B750 Loosen Short bar Black (-) Insulation coating NS-B750 Tighten Red (+) Bare wire NS-B750 Subwoofer Center Speakers output terminals of the amplifier (or receiver) SPEAKERS R +- L A -+ B Surround back Surround Notes • Placing this dictates the overall sound quality of the multi channel system. If one speaker...
Owners Manual
Page 4
... connect 1 Loosen the knob. 2 Remove 10 mm (3/8") of insulation from the terminals first, and then connect the mid-range/woofer and tweeter to the output terminals of the amplifier (or receiver), two pairs of cables for each of mid-range/woofer and tweeter used instead of standard connections. Consequently, purer sound quality can be expected. Black (-) Tweeter terminals Red (+) Short bar Woofer terminals 1 Remove the cover by pulling lightly on the cables...
... connect 1 Loosen the knob. 2 Remove 10 mm (3/8") of insulation from the terminals first, and then connect the mid-range/woofer and tweeter to the output terminals of the amplifier (or receiver), two pairs of cables for each of mid-range/woofer and tweeter used instead of standard connections. Consequently, purer sound quality can be expected. Black (-) Tweeter terminals Red (+) Short bar Woofer terminals 1 Remove the cover by pulling lightly on the cables...
Owners Manual
Page 5
... for any tools. • There are packed separately. SPECIFICATIONS Type 2-way bass reflex speaker system Non-Magnetic shielding type Driver 13 cm (5") cone woofer × 1 Advanced PMD 3 cm (1") aluminum dome tweeter DC diaphragm Impedance 6 Ω Frequency Response 60 Hz to 50 kHz (-10 dB) 100 kHz (-30dB) Nominal Input Power 30 W Maximum Input Power 120 W Sensitivity 87 dB/2.83 V/m Crossover Frequency 4 kHz Dimensions (W × H × D 198 × 350 × 290...
... for any tools. • There are packed separately. SPECIFICATIONS Type 2-way bass reflex speaker system Non-Magnetic shielding type Driver 13 cm (5") cone woofer × 1 Advanced PMD 3 cm (1") aluminum dome tweeter DC diaphragm Impedance 6 Ω Frequency Response 60 Hz to 50 kHz (-10 dB) 100 kHz (-30dB) Nominal Input Power 30 W Maximum Input Power 120 W Sensitivity 87 dB/2.83 V/m Crossover Frequency 4 kHz Dimensions (W × H × D 198 × 350 × 290...