Yamaha MV12 Support and Manuals
Get Help and Manuals for this Yamaha item
Popular Yamaha MV12 Manual Pages
Owner's Manual - Page 1
... the most out of your MV12/6 mixer and its functions, and to provide the user with an ideal balance of trouble-free use, please read this Owner's Manual thoroughly and keep it in a safe place for purchasing the YAMAHA MV12/6 Mixer.
The MV12/6 mixer is designed to enjoy years of operability, functionality, and simplicity. MIXER
Owner's Manual
Thank you for future...
Owner's Manual - Page 2
...CODE:
GREEN-AND-YELLOW : EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
As the colours of the wires in your authority, granted by YAMAHA KEMBLE MUSIC (U.K.) LTD. Owner's Manual Failure to follow instructions...coaxial type cable. MV12/6 - Cable/s supplied with the requirements listed in the USA.
3. Compliance with other electronic devices.
This product, when installed as follows:
...
Owner's Manual - Page 3
...of the rack or open a ventilation hole. You could receive an electrical shock. Cautions
• When rack-mounting the unit, allow enough free space around the unit for repair. Doing so...Manual or as possible, and unplug the power cable plug from the AC outlet, and contact your dealer about replacing defective components. Fire or electrical shock may cause a fire.
• Hold the power...
Owner's Manual - Page 4
...MV12...Specifications 14 Dimensions 16 Block and Level Diagrams 17
Caution: When the unit is installed in a rack, please use of tape decks for external effectors or a monitor system.
• The mixer supplies phantom power to provide easy connection of additional equipment. When installed in a rack
The main unit's power switch is equipped with XLR type input jacks. Owner's Manual
Power...
Owner's Manual - Page 5
...
Individually controls the level of control over high, mid and low frequency ranges at "G".
Owner's Manual
HIGH : 10kHz (shelving) MID : 2.5 kHz (peaking) LOW : 100Hz (shelving)
Frequency ...Input Select Switch located on the Connector Panel provides settings for the type of the signal entering the mixer to AUX2.
MV12/6 - The signal taken from either before the channel...
Owner's Manual - Page 6
...
3-4 BAL
ST
POST
[-6dB] AUX1
AUX2
EFFECT
GROUP1 GROUP2 GROUP3 GROUP4 STEREO L STEREO R AUX1 AUX2 EFFECT
MV12/6 - 4 Front & Rear Panels
y EFFECT Control
Controls the level of the signal sent from each channel to ... is ON (>), the signal is sent to the EFFECT bus. Owner's Manual
The BAL control knobs set the position within the stereo field of each signal that are combined and ...
Owner's Manual - Page 8
...three switches are used in digital effect ON (>) or OFF (?). Owner's Manual VOCAL ECHO 1 VOCAL ECHO 2 VOCAL ECHO 3 VOCAL ECHO 4
VOCAL ...clipping is imminent.
!4 POWER Indicator
The indicator will light when the main unit's power is sent from the ... and meter select switch to select the source to the ST OUT jacks. When set to OFF, the signal from the built-in effect is not sent.
•...MV12/6 -
Owner's Manual - Page 9
...power is set to any position other than MIC (+48V).
• MIC: Compatible with 50-600Ω microphones. • LINE: Compatible with a nominal output/impedance of the Input Channel. Both types are impedance balanced phone type jacks with 600Ω line level devices.
Owner's Manual... balanced XLR type and Euro-block connectors are supplied. e INSERT IN Jacks (CH 1-4) r...MV12/6 -
Owner's Manual - Page 10
... connected to a power amplifier, etc. Owner's Manual This jack can...buses. Make recording level adjustments on an MTR or an external mixer. balanced XLR type and Euro-block connectors. • XLR...: Cold, G: Ground)
Nominal output/impedance +4dB/600Ω
MV12/6 - The signal sent from this case, the TAPE IN control ...ST Mater Fader or Graphic EQ settings. u TAPE IN (L, R) Jacks
These...
Owner's Manual - Page 11
... select the source to the mixer. Its level is powered. Two types of jacks are connected to be monitored.
!3 POWER Switch
When the switch is ...Tip: hot Sleeve: ground
INPUT
OUTPUT
Ring Sleeve Tip Sleeve Tip
MV12/6 - Also, when turning the power OFF, turn on the power amp or powered speakers that are provided; balanced XLR type and Euro-block connectors.... system, etc. Owner's Manual
Owner's Manual - Page 13
... Euro-block connectors are supplied with a minus (-) driver. Feet
Four rubber feet are used without the cover attached.
According to the orientation that the device is installed, attach the rubber feet to the surface that is closed, turn the upper screw to the right to secure
the wire. 3. Owner's Manual
Insert the wires according...
Owner's Manual - Page 14
... is connected to the input channel (refer to the "0" position. MV12/6 - w Use the GAIN Control on the power amp to the Master Section. e Press each channel to adjust the... Basic Setup
Monitor Speakers
Main Speakers
Sub Woofer, etc. Owner's Manual Power Amplifier
Headphones
AUX 1 SEND
Effector
INSERT OUT
AUX 2 (PRE) SEND
INSERT IN
PHONES
Set the POST Switch to the power amplifier....
Owner's Manual - Page 15
... Master Fader and the GROUP 1-4 Faders to the INPUT jacks and connect a power amp, that drives the side speakers to adjust the speaker's volume.
REC OUT
TAPE IN Set the POST Switch to the "0" position. Applications 13
Example 2) Banquet Room Setup Using Independent Speakers
Main Speaker R
Side Speakers 24
Monitor Speakers
Main Speaker...
Owner's Manual - Page 16
14 Supplement
Supplement
Specifications
I General specifications
Frequency response
20Hz-20kHz +1dB, -3dB @+4dB, 600Ω (INPUT GAIN Control at minimum level)
(CH MIC INPUT to ST, GROUP OUT/AUX, EFFECT SEND)
Total harmonic distortion
Owner's Manual - Page 17
... the lowest level that will produce the nominal output level when the unit is set to change without prior notice.
before clipping
+4 dB (1.23V)
+24 dB ...(T=Signal, R= Gnd, S=Gnd): unbalanced type.
• 0dB=0.775Vrms, 0dBV=1Vrms
I Input Specifications
Input
Input
GAIN
connectors Select Switch Control
MIC (+48V) MIC
-60
INPUT (1-8)
LINE
-34
MIC...)
Max. MV12/6 - Owner's Manual
Yamaha MV12 Reviews
We have not received any reviews for Yamaha yet.