Owner's Manual
Page 2
... If the output level of signals received at the SPEAKERS jacks (output of the EMX5000-20, EMX5000-12 owner's manual have been revised. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. A- 1+ 2+ B+ 2- Check the output signal level via the internal power amplifier. Please refer to the following revisions rather than the corresponding sections of the...
... If the output level of signals received at the SPEAKERS jacks (output of the EMX5000-20, EMX5000-12 owner's manual have been revised. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. A- 1+ 2+ B+ 2- Check the output signal level via the internal power amplifier. Please refer to the following revisions rather than the corresponding sections of the...
Owner's Manual
Page 7
...32 Installing an optional rack mount kit 32 Block/Level Diagram 33 EMX5000-20/EMX5000-12-Owner's Manual The effects can be used to add reverb or ambience to the acclaimed Yamaha SPX series of multi-effect units. Introduction 5 Introduction Thank you... switch the maximum output of the amp between three levels. MONO), two AUX (AUX1AUX2) or monaural (bridge connection). • In addition to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer...
...32 Installing an optional rack mount kit 32 Block/Level Diagram 33 EMX5000-20/EMX5000-12-Owner's Manual The effects can be used to add reverb or ambience to the acclaimed Yamaha SPX series of multi-effect units. Introduction 5 Introduction Thank you... switch the maximum output of the amp between three levels. MONO), two AUX (AUX1AUX2) or monaural (bridge connection). • In addition to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer...
Owner's Manual
Page 19
... (control panel K). Connect stage-monitoring amplifiers or powered speakers here. The nominal output level is +4 dB. C MONO OUT jack This phone jack mixes the STEREO bus signals and output a monaural signal. EMX5000-20/EMX5000-12-Owner's Manual Adjust the recording level on the recording device. 7 ST ... sold Yamaha FC5 foot switch can connect either phone plugs or RCA phono plugs, as a cassette deck, to this jack. The nominal output level is +4 dB. 0 ST OUT jacks These phone jacks output the line level signal of the signals output from the mixer section....
... (control panel K). Connect stage-monitoring amplifiers or powered speakers here. The nominal output level is +4 dB. C MONO OUT jack This phone jack mixes the STEREO bus signals and output a monaural signal. EMX5000-20/EMX5000-12-Owner's Manual Adjust the recording level on the recording device. 7 ST ... sold Yamaha FC5 foot switch can connect either phone plugs or RCA phono plugs, as a cassette deck, to this jack. The nominal output level is +4 dB. 0 ST OUT jacks These phone jacks output the line level signal of the signals output from the mixer section....
Owner's Manual
Page 31
...adequate ventilation. Possible reasons for following three points to prevent the problem from the EFFECT SEND jack to the connected effect processor. Powered Mixer Q&A Q: The built-in the MASTER CONTROL section is not effective. Then the effect sound is sent from the excessive load ...device is not ventilated sufficiently, refer to the cautions given at the beginning of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual If the load impedance (including a short) is not powerful enough relative to the level of the connected main section when doing so. Please contact your dealer. ...
...adequate ventilation. Possible reasons for following three points to prevent the problem from the EFFECT SEND jack to the connected effect processor. Powered Mixer Q&A Q: The built-in the MASTER CONTROL section is not effective. Then the effect sound is sent from the excessive load ...device is not ventilated sufficiently, refer to the cautions given at the beginning of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual If the load impedance (including a short) is not powerful enough relative to the level of the connected main section when doing so. Please contact your dealer. ...
Owner's Manual
Page 33
... 1. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip mixer CH INPUT A -60 (CH1-8/1-16) -16 CH INPUT B -60 (CH1-8/1-16) -16 ST INPUT -34 (CH9-12/17-20) +10 ST SUB IN (1, 2) 2TR IN (L, R) INSERT IN (CH1-8/1-16) POWER AMP IN (A, B) 5 kΩ 50 kΩ 10 ... specifications 31 Dimensions (WxHxD) Weight Accessories 682 × 158 × 538 mm (EMX5000-20) / 478 × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual s Input specifications Input terminals Gain control Actual load impedance For use with nominal...
... 1. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip mixer CH INPUT A -60 (CH1-8/1-16) -16 CH INPUT B -60 (CH1-8/1-16) -16 ST INPUT -34 (CH9-12/17-20) +10 ST SUB IN (1, 2) 2TR IN (L, R) INSERT IN (CH1-8/1-16) POWER AMP IN (A, B) 5 kΩ 50 kΩ 10 ... specifications 31 Dimensions (WxHxD) Weight Accessories 682 × 158 × 538 mm (EMX5000-20) / 478 × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual s Input specifications Input terminals Gain control Actual load impedance For use with nominal...